| Age | Commit message (Collapse) | Author |
|---|
|
Add i.MX8QM ROM 7720a1 board support
Boot log as below:
U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Advantech iMX8QM Qseven series
Board: ROM-7720-A1 4GB
Build: SCFW 65afe5f6
Boot: SD2
DRAM: 4 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@5a060000
Out: serial@5a060000
Err: serial@5a060000
Net: eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet@5b050000
Hit any key to stop autoboot: 0
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
|
|
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
To avoid hardcoded offset when adding u-boot.cnt to flash.bin, we use
flexible offset which is calculated based on the size of the container
image generated int the first stage. And pad u-boot.cnt at 1KB
alignment.
So add code to get the offset when SPL loading u-boot.cnt.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit caceb739ea07 ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Build flash.bin for i.MX8 when SPL enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
To enable SPL for i.MX8, we could reuse code in arch/arm/mach-imx.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No need to build bootaux in SPL stage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Rename mx8m,MX8M to imx8m,IMX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
|
|
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The make macro to check if the binary exceeds the board size limit is
taken straight from the root Makefile.
Without this and e.g. enabled EFI Vybrid fails booting as the regular
size limit check does not take the final u-boot.imx binary size into
account which is bigger due to alignment as well as IMX header stuff.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Introduce a new script to check whether file exists and
use that check in Makefile to avoid break CI system.
The script return 1 when the required files not exists, return 0
when files exists. The script will ignore check to u-boot-dtb.bin,
because if there is something wrong to generate u-boot-dtb.bin,
there must be some code error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
When building i.MX8/8X board, use imx8image type.
`-e $(CONFIG_SYS_TEXT_BASE)` is not needed, but
no harm to keep it for i.MX8/8X
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add Kconfig entry for i.MX8QXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The board_video_skip() implementation in imx-common/video.c works
on i.MX5x as well, so loosen the SoC filter in Makefile to make it
available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Each imx image is created by a separate sub-make and during this process
the mkimage config file is run though cpp.
The cpp output is to the same file no matter what imx image is being
created.
This means if two imx images are generated in parallel they will attempt
to independently produce the same pre-processed mkimage config file at
the same time.
Avoid the problem by making the pre-processed config file name unique
based on the imx image it will be used in. This way each image will
create a unique config file and they won't clobber each other when run
in parallel.
This should fixed the build bug referenced in b5b0e4e3 ("imximage:
Remove failure when no IVT offset is found").
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Compile files for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add SoC level initialization code
- arch_cpu_init
- mmu table
- detect cpu revision
- reset cpu and wdog settings
- timer init
- wdog settings
- lowlevel init to save/restore registers
- a few dummy header file to avoid build failure
- ft_system_setup
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The mx7 mmc env code is shared by i.MX8M, so move it to mmc_env.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Move imx_get_mac_from_fuse to a new mac.c for i.MX6/7.
Since fuse regs structure are different for i.MX6/7, use mac
address offset in code and define a new local struture
imx_mac_fuse.
Also sort the config order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Add SiP (Silicon Provider) services function to issue
SMC call to Arm Trusted Firmware.
More SiP information could be found in
https://github.com/ARM-software/arm-trusted-firmware/blob/master/
docs/arm-sip-service.rst
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The "clocks" and "bootaux" commands are only usable in full U-Boot, not
SPL, so do not link them inside of SPL. Rework a little of the bootaux
related code to make use of __weak and declare parts of it static as
it's local to the file.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Introduce a new config symbol to select the i.MX
General Purpose Timer (GPT).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
