summaryrefslogtreecommitdiff
path: root/arch/arm/mach-uniphier/Makefile
AgeCommit message (Collapse)Author
2020-08-18ARM: uniphier: remove unused uniphier_pin_init()Masahiro Yamada
This function is unused since commit 862274913f8f ("bus: uniphier-system-bus: move hardware init from board files"). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-11ARM: uniphier: remove NAND reset codeMasahiro Yamada
Now that commit 3e57f879eee6 ("mtd: nand: raw: denali: Assert reset before deassert") added the reset assertion, this code in the board file is unneeded. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-11ARM: uniphier: remove sbc/ directoryMasahiro Yamada
Now that this directory contains only uniphier_sbc_boot_is_swapped(), move it to boot-device.c and delete the sbc/ directory entirely. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-28ARM: uniphier: move NAND reset assertion to U-Boot proper from SPLMasahiro Yamada
The comment /* deassert reset */ is wrong. It asserts the reset. It no longer needs to stay in SPL. The NAND controller reset is handled in the driver. So, this assert can be moved to the board_init() of U-Boot proper. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-07-10ARM: uniphier: detect register base addresses run-timeMasahiro Yamada
Until the last SoC, the register addresses have been hard-coded because they are always constant. For a planned new SoC, the register bases will be completely changed. I insist on supporting multiple SoCs/boards by a single defconfig (uniphier_v8_defconfig) since duplicating similar defconfig files is a maintenance burden. The base addresses must be fixed-up at run-time somehow. Previously, the board init code identified the SoC by reading out the SG_REVISION register. This is much easier than parsing DT. You cannot do it any more because the base address of SG will be changed. The SG_REVISION register exists to read out the SoC ID, but you never know its address before identifying the SoC. Oh well. So, the possible solution is to parse the DT, and find out the node with "*-soc-glue" compatible string. Then, sg_base is set to the value of the "reg" property. The sc_base is set up likewise. It is worth noting a pit-fall. Having sc_base and sg_base in the global scope will make the life easier, but the global variables are poorly supported before the relocation. In fact, the .bss section overwraps with DT. Allocating them in the .bss section would break DT. So, I gave dummy initializers to assign them in the .data section. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-07-10ARM: uniphier: check DT to determine whether to initialize SBCMasahiro Yamada
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot initialize SBC (System Bus Controller), which may not be really necessary. Check the "socionext,uniphier-system-bus" node in DT run-time. If and only if it is found and its "status" property is okay, initialize the SBC block. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-25ARM: uniphier: split ft_board_setup() out to a separate fileMasahiro Yamada
Prepare to add more fdt fixup code. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-07arm: v7: Kconfig: Rename CPU_V7 as CPU_V7ALokesh Vutla
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under armv7 folder. This led to a misconception of creating separate folders for armv7m and armv7r. There is no reason to create separate folder for other armv7 based architectures when it can co-exist with few Kconfig symbols. As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and can co exist in the same folder. Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Suggested-by: Alexander Graf <agraf@suse.de> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-20ARM: uniphier: enable PSCI sysreset for uniphier_v8_defconfigMasahiro Yamada
This configuration is supposed to be used with ARM Trusted Firmware, so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of U-Boot's own reset code because we need to coordinate with SCP (System Control Processor) for the system-level power management. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: rework spl_boot_device() and related codeMasahiro Yamada
The current implementation has ugly switch statements here and there, and duplicates similar code. Rework it using table lookups for SoC data and reduce code duplication. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: move spl_boot_mode() to a separate fileMasahiro Yamada
The spl_boot_mode() is unrelated to the other code in this file. Besides, this function is only called from common/spl/spl_mmc.c, so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: move MMC code to a separate fileMasahiro Yamada
Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up with unrelated code; there is no reason why the "mmcsetn" command must be placed in this file. Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29ARM: uniphier: compile board data only for SPLMasahiro Yamada
Now U-Boot proper need not get the uniphier_boards array. Compile it only for SPL. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22ARM: uniphier: simplify SoC ID get functionMasahiro Yamada
Currently, uniphier_get_soc_type() converts the SoC ID (this is read from the revision register) to an enum symbol to use it for SoC identification. Come to think of it, there is no need for the conversion in the first place. Using the SoC ID from the register as-is a straightforward way. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18ARM: uniphier: move SBC and Support Card init code to U-Boot properMasahiro Yamada
Initialize SBC and Support Card in U-Boot proper instead of SPL. We may run different firmware (ex. ARM Trusted Firmware) before U-Boot, and basic SoC initialization may be done there. In that case, SPL may not be used. The motivation for preparing SBC and Support Card in SPL was to use LED for early debugging, but this is not mandatory to boot SoCs. With this commit, LED will be unavailable in SPL, but we can use a debug serial instead. So, this change will not be a big deal. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18ARM: uniphier: refactor spl_init_board()Masahiro Yamada
Merge init-*.c into a single file using a table of callbacks because the initialization flow is almost common among SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: refactor MEMCONF init codeMasahiro Yamada
Currently, memconf-sld3.c and memconf-pxs2.c duplicate the code. There are 3 patterns in terms of MEMCONF init: - DRAM 2 channels: LD4, sLD8, Pro4, Pro5, LD11 - DRAM 3 channels: sLD3 - DRAM 3 channels (Ch2 is disable by MEMCONF[21]): Pxs2, LD20 All of them can be moved into a single file by a little more refactoring. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19ARM: uniphier: collect clock/PLL init code into a single directoryMasahiro Yamada
Now PLLs for DRAM controller are initialized in SPL, and the others in U-Boot proper. Setting up all of them in a single directory will be helpful when we want to share code between SPL and U-Boot proper. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18ARM: uniphier: move XIRQ pin-mux settings of LD11/LD20Masahiro Yamada
This is the last code in the mach-uniphier/pinctrl/ directory. Push the remaining code out to delete the directory entirely. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18ARM: uniphier: consolidate System Bus pin-mux settings for LD11/LD20Masahiro Yamada
Use the pin-mux data in the pinctrl drivers by directly calling pinctrl_generic_set_state(). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18ARM: uniphier: consolidate NAND pin-mux settingsMasahiro Yamada
The NAND subsystem has not supported the Driver Model yet, but the NAND pin-mux data are already in the pinctrl drivers. Use them by calling pinctrl_generic_set_state() directly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: merge board init functions into board_init()Masahiro Yamada
Currently, the UniPhier platform calls several init functions in the following order: [1] spl_board_init() [2] board_early_init_f() [3] board_init() [4] board_early_init_r() [5] board_late_init() The serial console is not ready at the point of [2], so we want to avoid using [2] from the view point of debuggability. Fortunately, all of the initialization in [2] can be delayed until [3]. I see no good reason to split into [3] and [4]. So, merge [2] through [4]. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: use checkboard() instead of misc_init_f()Masahiro Yamada
We can use checkboard() stub to show additional board information, so misc_init_f() should not be used for this purpose. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24ARM: uniphier: add PH1-LD20 SoC supportMasahiro Yamada
This is the first ARMv8 SoC from Socionext Inc. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24ARM: uniphier: support Debug UARTMasahiro Yamada
For ARM32 architecture, CONFIG_DEBUG_LL is available for early low-level debugging (and actually UniPhier 32bit SoCs use it), but ARM64 architecture does not support it. Instead, CONFIG_DEBUG_UART is available as an architecture-independent debug facility. This commit supports it on all the UniPhier SoCs (including the new ARMv8 SoCs), which is very useful for new SoC bringups. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-01ARM: uniphier: prepare directory structure for ARMv8 SoC supportMasahiro Yamada
Before adding ARMv8 support, this commit refactors the directory structure. Move ARMv7 specific files to arch/arm/mach-uniphier/arm32 to avoid a mess by mixture of ARMv7 and ARMv8 code. Also move the "select CPU_V7" to the lower-level menu because we will have to select ARM64 instead of CPU_V7 for ARMv8 SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: uniphier: fix makefiles to build cmd_ddr(m)phy.cMasahiro Yamada
The U-Boot proper building needs to descend arch/arm/mach-uniphier/dram to build these commands. Fixes: 93d92d46cd01 ("ARM: uniphier: add dump command for DDR Multi PHY registers") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: uniphier: create early page table at run-timeMasahiro Yamada
UniPhier SoCs are not equipped with dedicated on-chip SRAM. Instead, locked outer cache is used as RAM area during the early boot stage where DRAM is not ready yet. This effectively means MMU must be always enabled while we are in SPL. Currently, the SPL image for UniPhier SoCs contains the page table statically defined at compile time. It has been a burden because the 16KB page table occupies a quarter memory footprint of the 64KB SPL image. Finally, there is no more room to implement new features in SPL. Setting aside the NOR boot mode, this issue can be solved by creating the page table onto RAM at run time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13ARM: uniphier: move cmd_pinmon.c to boot-mode subdirectoryMasahiro Yamada
This command shows the boot mode pins, so it would be more at home in the boot-mode subdirectory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13ARM: uniphier: move cmd_ddrphy.c to dram subdirectoryMasahiro Yamada
This command shows the register dump of the DDR PHY, so it would be more at home in the dram subdirectory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-12-23ARM: uniphier: merge umc/ and ddrphy/ into a single directoryMasahiro Yamada
The UMC (Universal Memory Controller) and the DDR PHY block are highly related to each other. It is better to have both code in the same directory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-12-23ARM: uniphier: compile uniphier_get_board_param() for U-Boot properMasahiro Yamada
Compile this file for U-Boot proper as well as SPL, so that the U-Boot proper can call uniphier_get_board_param(). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: allow to enable multiple SoCsMasahiro Yamada
Before this commit, the Kconfig menu in mach-uniphier only allowed us to choose one SoC to be compiled. Each SoC has its own defconfig file for the build-test coverage. Consequently, some defconfig files are duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and CONFIG_{SOC_NAME}=y. Now, most of board-specific parameters have been moved to device trees, so it makes sense to include init code of multiple SoCs into a single image as long as the SoCs have similar architecture. In fact, some SoCs of UniPhier family are very similar: - PH1-LD4 and PH1-sLD8 - PH1-LD6b and ProXstream2 (will be added in the upcoming commit) This commit will be helpful to merge some defconfig files for better maintainability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: unify low-level debug init codeMasahiro Yamada
Move init code of low-level debug into a single file. This is helpful to create an image that runs on multiple SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: rename CONFIG_MACH_* to CONFIG_ARCH_UNIPHIER_*Masahiro Yamada
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify they belong to UniPhier SoC family. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: move CONFIG_SUPPORT_CARD_* macros to local fileMasahiro Yamada
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally. Move them to a C file as local macros. Also, rename the C file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: drop DCC micro support card supportMasahiro Yamada
Historically (for compatibility with very old platforms), two different types of micro support cards have been used with the UniPhier SoC development boards. It has been painful to maintain both. Having one of them is enough. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-07-23ARM: UniPhier: add PH1-sLD3 SoC supportMasahiro Yamada
The init code for UMC (Unified Memory Controller) and PLL has not been mainlined yet, but U-boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: optimize kicking secondary CPUs codeMasahiro Yamada
Currently, the secondary CPU(s) are kicked three times: Boot ROM ---(kick)--> SPL ---(kick)--> U-boot ---(kick)--> Linux. It makes the boot sequence very complicated. This commit merges the first and the second kicks, so the secondary CPU(s) can directly jump from SPL to Linux. arch/arm/mach-uniphier/smp.S is no longer necessary. Linux boot test passed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: add empty lowlevel_init to U-boot properMasahiro Yamada
To remove the ifdef conditional of CONFIG_SKIP_LOWLEVEL_INIT, add late_lowlevel_init.S to U-Boot proper. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-01ARM: UniPhier: consolidate MEMCONF setting codeMasahiro Yamada
This code is duplicated in ph1-ld4/sg_init.c and ph1-pro4/sg_init.c. Merge the same code into a new file, memconf.c. The helper functions no longer have to be placed in the header file. Also, move them into memconf.c. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01ARM: UniPhier: move SoC sources to mach-uniphierMasahiro Yamada
Move arch/arm/cpu/armv7/uniphier/* -> arch/arm/mach-uniphier/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>