summaryrefslogtreecommitdiff
path: root/arch/arm/mach-uniphier
AgeCommit message (Collapse)Author
2015-09-25ARM: uniphier: fix init page table for ProXstream2/PH1-LD6b USB bootMasahiro Yamada
Currently, the USB boot mode is supported by an external loader and U-boot proper image is put on the section 0. This commit allows access there. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: add ProXstream2 and PH1-LD6b supportMasahiro Yamada
The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: add PH1-Pro5 supportMasahiro Yamada
The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: allow to enable multiple SoCsMasahiro Yamada
Before this commit, the Kconfig menu in mach-uniphier only allowed us to choose one SoC to be compiled. Each SoC has its own defconfig file for the build-test coverage. Consequently, some defconfig files are duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and CONFIG_{SOC_NAME}=y. Now, most of board-specific parameters have been moved to device trees, so it makes sense to include init code of multiple SoCs into a single image as long as the SoCs have similar architecture. In fact, some SoCs of UniPhier family are very similar: - PH1-LD4 and PH1-sLD8 - PH1-LD6b and ProXstream2 (will be added in the upcoming commit) This commit will be helpful to merge some defconfig files for better maintainability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: unify low-level debug init codeMasahiro Yamada
Move init code of low-level debug into a single file. This is helpful to create an image that runs on multiple SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: fix glitch signal problem for low-level debugMasahiro Yamada
Currently, IECTRL is enabled after pin-mux settings for the low-level debugging for PH1-LD4 and PH1-sLD8. While IECTRL is disabled, input signals are pulled-down, i.e. glitch signal (Low to High transition) problem occurs if pin-mux is set up first. As a result, one invalid character is input to the UART block and the auto-boot counting is terminated immediately. The correct initialization procedure is: [1] Enable IECTRL (if IECTRL exists for the pins) [2] Set up pin-muxing [3] Deassert the reset of the hardware block Currently, the low-level debugging is working for PH1-sLD3 and PH1-Pro4, but just in case, follow the sequence for all the SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: delete unneeded input enable for low-level debugMasahiro Yamada
The UART I/O ports for PH1-Pro4 has no input enable controlling. This code is useless. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: rename CONFIG_MACH_* to CONFIG_ARCH_UNIPHIER_*Masahiro Yamada
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify they belong to UniPhier SoC family. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: allow to disable CONFIG_MICRO_SUPPORT_CARDMasahiro Yamada
Without this, build fails if CONFIG_MICRO_SUPPORT_CARD is disabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: move CONFIG_SUPPORT_CARD_* macros to local fileMasahiro Yamada
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally. Move them to a C file as local macros. Also, rename the C file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: refactor LED functionMasahiro Yamada
The macro, led_write(), is now only used in C sources. There is no more reason to keep the tricky assembly macro. Replace it with a new C function led_puts(). Also, rename board.h to micro-support-card.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: remove useless wrapper functionsMasahiro Yamada
The wrapper functions, uniphier_board_*, are just making function calls complex. Remove them. Also, use empty inline functions in case CONFIG_MICRO_SUPPORT_CARD is disabled, so that prototype checking works. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: remove unused header fileMasahiro Yamada
This has been unused since commit f4e190e317b8 ("ARM: uniphier: enable SPL_OF_CONTROL"). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: parse device tree to determine DRAM base and sizeMasahiro Yamada
Device tree specifies the available memory ranges in its "/memory" node. Use it to simplify the CONFIG defines. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: remove ifdef CONFIG_{SOC} conditionals from sg-regs.hMasahiro Yamada
To achieve the complete run-time configuration by device trees, ifdef conditionals in header files are not preferable. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: change the external bus address mappingMasahiro Yamada
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces 0x00000000 - 0x0fffffff 0x40000000 - 0x4fffffff are both mapped to the external bus (also called system bus), so either was OK. In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is assigned for the serial NOR interface. Going forward, use the latter for the external bus. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-25ARM: uniphier: drop DCC micro support card supportMasahiro Yamada
Historically (for compatibility with very old platforms), two different types of micro support cards have been used with the UniPhier SoC development boards. It has been painful to maintain both. Having one of them is enough. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-25ARM: uniphier: drop ad-hoc input enable settingsMasahiro Yamada
These input enable settings are handled by the pinctrl drivers. Because the external bus pins are input-enabled by default, on-board devices such as LED still work fine even with this delayed input enabling. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25ARM: uniphier: drop ad-hoc early pin-muxing settingsMasahiro Yamada
As the UniPhier serial driver had already switched to Drive Model and the pinctrl drivers are now enabled, these pin-muxing settings are properly handled by the pinctrl drivers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-31ARM: uniphier: enable SPL_OF_CONTROLMasahiro Yamada
Device Tree really improves code maintainability and is now available for SPL too. This is the state-of-the-art implementation in U-boot. The board files (platform data) are no longer needed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-30ARM: uniphier: fix build error when CONFIG_DEBUG_LL is definedMasahiro Yamada
The build error happens if CONFIG_DEBUG_LL and CONFIG_MACH_PH1_SLD3 are both enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-07-23ARM: UniPhier: add PH1-sLD3 SoC supportMasahiro Yamada
The init code for UMC (Unified Memory Controller) and PLL has not been mainlined yet, but U-boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-07-02ARM: UniPhier: add IDs for PH1-Pro5, ProXstream2, PH1-LD6bMasahiro Yamada
This prepares for new SoCs support. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: add pin mux setting for NAND CS1 of PH1-Pro4Masahiro Yamada
The chip select 1 of the NAND controller is available if you want to use, although the pins are shared with UART port 2. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: fix pin mux setting for USB port 2 of PH1-sLD8Masahiro Yamada
The register value should be 1, not 4. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: update DDR PHY register map for PH1-Pro5Masahiro Yamada
PH1-Pro5 includes a newer version of DDR PHY IP. Some registers have been added to the reserved areas. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: set MACH_PH1_PRO4 as default SoCMasahiro Yamada
One disadvantage of commit a26cd04920dc (arch: Make board selection choices optional) is that Kconfig could create such an insane .config file that no board is selected. As PH1-Pro4 is the main stream of UniPhier SoC family, rip off the "optional" again in favor of PH1-Pro4 as the default SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: remove meaningless CONFIG_SPL_BUILD ifdefsMasahiro Yamada
This file is only built for SPL. These ifdef conditionals are unnecessary because UniPhier platform now supports UART on SPL. Show appropriate messages on error. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: remove unnecessary cache coherency codeMasahiro Yamada
Cache coherency for SMP is cared by Linux. In U-Boot, the secondary CPU(s) are just sleeping. Nothing in memory is shared with the primary CPU. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: use 32 bit register access for debug UART settingMasahiro Yamada
For the same reason as commit d0c47b3ef7c5 (serial: UniPhier: use 32 bit register access), use "str" instead of "strb" for the LCR register setting. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: update the vendor name of UniPhier in KconfigMasahiro Yamada
The business for UniPhier Soc family has been transferred from Panasonic Corporation to Socionext Inc. Update the SoC select menu in Kconfig. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-31ARM: UniPhier: replace <asm/io.h> with <linux/io.h>Masahiro Yamada
In the Linux coding style, it is recommended to include <linux/io.h> rather than <asm/io.h>. Follow this trend. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-12arch: Make board selection choices optionalJoe Hershberger
By making the board selections optional, every defconfig will include the board selection when running savedefconfig so if a new board is added to the top of the list of choices the former top's defconfig will still be correct. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
2015-03-28malloc_f: enable SYS_MALLOC_F by default if DM is onMasahiro Yamada
This option has a bool type, not hex. Fix it and enable it if CONFIG_DM is on because Driver Model always requires malloc memory. Devices are scanned twice, before/after relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc memory before relocation. As it is board-independent, handle it globally. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
2015-03-28malloc_f: remove redundant defalut values of CONFIG_SYS_MALLOC_F_LENMasahiro Yamada
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig as 0x400. Each defconfig or Kconfig need not repeat the same value. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
2015-03-24ARM: UniPhier: remove unnecessary ifdef conditionalMasahiro Yamada
The callee (arch/arm/lib/cache-cp15.c) has a #ifdef CONFIG_SYS_DCACHE_OFF conditional. The same conditional in the caller (arch/arm/mach-uniphier/cache_uniphier.c) is redundant. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: disable L2 cache by lowlevel_init of U-Boot properMasahiro Yamada
The L2 cache is used as a temporary SRAM on SPL. Now the secondary CPUs store the necessary code for jumping to Linux on their L1 I-caches. So, the L2 cache can be disabled much earlier, at the very entry of U-Boot proper (lowlevel_init). This makes the boot sequence clearer. Also, as the L1 cache has been disabled by the start.S, enable_caches() does not need to do it again. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: optimize kicking secondary CPUs codeMasahiro Yamada
Currently, the secondary CPU(s) are kicked three times: Boot ROM ---(kick)--> SPL ---(kick)--> U-boot ---(kick)--> Linux. It makes the boot sequence very complicated. This commit merges the first and the second kicks, so the secondary CPU(s) can directly jump from SPL to Linux. arch/arm/mach-uniphier/smp.S is no longer necessary. Linux boot test passed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: fix typos in commentsMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: add empty lowlevel_init to U-boot properMasahiro Yamada
To remove the ifdef conditional of CONFIG_SKIP_LOWLEVEL_INIT, add late_lowlevel_init.S to U-Boot proper. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: use CONFIG_SPL_STACK to define SPL stack pointerMasahiro Yamada
Ifdef conditionals for CONFIG options are not Kconfig-friendly. Instead, define CONFIG_SPL_STACK to prepare for Kconfig moves. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: enable Driver Model and UART on SPLMasahiro Yamada
Enable CONFIG_SPL_DM and CONFIG_SPL_SERIAL_SUPPORT, which provide Driver Model UART support on SPL. CONFIG_SYS_SPL_MALLOC_{START,SIZE} should be dropped because simple malloc is preferred on SPL. Dlmalloc requires some static variables on .data section that is not available yet for NOR boot mode etc. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: move UART pin settings to SPLMasahiro Yamada
The UniPhier platform is going to enable Driver Model and UART support on SPL. Move UART pin settings to early_pin_init(), which is called from SPL. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: move platform devices to SPLMasahiro Yamada
Since we do not have OF_CONTROL support for SPL, platform devices are necessary to enable Driver Model on SPL. To prepare for that, move platdevice.o to SPL and enable it by CONFIG_SPL_DM. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: include PH1-LD4 Makefile from PH1-sLD8Masahiro Yamada
The two Makefiles arch/arm/mach-uniphier/{ph1-ld4,ph1-sld8}/Makefile are completely the same. We can improve the maintainability by having one to include the other. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-24ARM: UniPhier: remove unnecessary CONFIG_SYS_SOCMasahiro Yamada
Since commit a86ac9540e20 (ARM: UniPhier: include <mach/*.h> instead of <asm/arch/*.h>), UniPhier platform does not need the symbolic link arch/arm/include/asm. This option is not necessary either. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-01ARM: UniPhier: remove SSC_WAY_SIZE and SSC_NUM_ENTRIES macrosMasahiro Yamada
Each way of the system cache has 256 entries for PH1-Pro4 and older SoCs, whereas 512 entries for PH1-Pro5 and newer SoCs. The line size is still 128 byte. Thus, the way size is 32KB/64KB for old/new SoCs. To keep lowlevel_init SoC-independent, set BOOT_RAM_SIZE to the constant value 32KB. It is large enough for temporary RAM and should work for all the SoCs of UniPhier family. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01ARM: UniPhier: remove stop_mpll() from PH1-Pro4 PLL initializationMasahiro Yamada
This function was intended for MN2WS0235 (what we call PH1-Pro4TV). On that SoC, MPLL is already running on the power-on reset and it makes sense to stop the PLL at early boot-up. On the other hand, PH1-Pro4(R) does not have SC_MPLLOSCCTL register, so this function has no point. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01ARM: UniPhier: consolidate MEMCONF setting codeMasahiro Yamada
This code is duplicated in ph1-ld4/sg_init.c and ph1-pro4/sg_init.c. Merge the same code into a new file, memconf.c. The helper functions no longer have to be placed in the header file. Also, move them into memconf.c. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01ARM: UniPhier: support 1CS support card for all the UniPhier SoCsMasahiro Yamada
Two support card variants are used with UniPhier reference boards: - 1 chip select support card (original CPLD) - 3 chip selects support card (ARIMA-compatible CPLD) Currently, the former is only supported on PH1-Pro4, but it can be expanded to PH1-LD4, PH1-sLD8 with a little code change. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>