| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Given gcc-6.1 and later we can now safely have strings discarded when
the functions are unused. This lets us drop certain cases of not
building something so that we don't have the strings brought in when the
code was discarded. Simplify the code now by dropping guards we don't
need now.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13 carry altenate
function, ALT5 for ARM JTAG
Signed-off-by: Henry Zhang <henryzhang62@yahoo.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746
and STM32F769 discovery boards
There is a hardware issue on these boards, it misses a pullup on the GPIO line
used as card detect to allow correct SD card detection.
As workaround, cd-gpios property is not present in DT.
So SD card is always considered present in the slot.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
STM32F469 SoC uses an arm_pl180_mmci SDIO controller.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
_ Add gpio compatible and aliases for stm32f469
_ Add FMC sdram node
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This DT file comes from kernel v4.15-rc1
stm32f469-pinctrl.dtsi header has been updated with correct
STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In order to use common clock driver between STM32F4 and
STM32F7, remove clock_get() call
As APB_PSC is always set to 2, only case when
clock_get(CLOCK_AHB) != clock_get(CLOCK_APB1) is kept
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
_ Add gpio compatible and aliases for stm32f429
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
All these files comes from kernel v4.15-rc1.
Update some header with correct STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The DB-88F6820-AMC connects ethernet@34000 and ethernet@70000 which are
labeled as eth2 and eth0 in armada-38x.dts. The ethernet@30000 (eth1) is
not used on the AMC board.
This eliminates the following bootup message
Device 'ethernet@70000': seq 0 is in use by 'ethernet@34000'
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
By applying this patch, we are ensuring that the code paths
responsible for applying errata workarounds are also exercised
on CPU revisions, which actually don't need these workarounds.
Only CONFIG_ARM_ERRATA_621766, CONFIG_ARM_ERRATA_454179,
CONFIG_ARM_ERRATA_725233 and CONFIG_ARM_ERRATA_430973 are
covered by this patch (Cortex-A8).
This improves code coverage when testing U-Boot builds
on newer hardware. In particular, the problematic commit
00bbe96ebabb ("arm: omap: Unify get_device_type() function")
would break both BeageBoard and BeagleBoard XM rather than
just older BeagleBoard.
As an additional bonus, we need fewer instructins and the SPL
size is reduced.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
I do not see a good reason to do this by a CONFIG option that affects
all SoCs. The ram_size can be adjusted by dram_init() at run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
LD20 / PXs3 boards are equipped with a large amount of memory beyond
the 32 bit address range. U-Boot relocates itself to the end of the
available RAM.
This is a problem for DMA engines that only support 32 bit physical
address, like the SDMA of SDHCI controllers.
In fact, U-Boot does not need to run at the very end of RAM. It is
rather troublesome for drivers with DMA engines because U-Boot does
not have API like dma_set_mask(), so DMA silently fails, making the
driver debugging difficult.
Hide the memory region that exceeds the 32 bit address range. It can
be done by simply carving out gd->ram_size. It would also possible to
override get_effective_memsize() or to define CONFIG_MAX_MEM_MAPPED,
but dram_init() is a good enough place to do this job.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Bind rockchip reset to clock-controller with rockchip_reset_bind().
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Introduce a new config symbol to select the i.MX
General Purpose Timer (GPT).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Since commit 051ba9e082f7 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
|
|
commit 20f14714169 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
|
|
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Enable sdmmc node in SPL and add it to boot order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tags:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
Since commit 999a78d5cf00 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110")
dtc warns about:
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000
Fix this by adding a node for the tzic interrupt controller.
Copied from "<Linux>/arch/arm/boot/dts/imx53.dts"
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:
In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2
Add HAS_CAAM configuration to avoid this error.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
MX6UL contains features that MX6ULL doesn't support.
Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS.
The motivation for doing this change is that MX6UL supports CAAM and
MX6ULL does not.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
"ethernet" node fix-up for device tree happens before Linux boot.
There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
|
|
|
|
Using writel causes a "Synchronous Abort". Invert the arguments.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
|
|
Update README file to note LS2088A and LS1088A don't support booting
from NAND flash.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Rockchip release bl31.elf file for armv8 SoCs like rk3399, rk3328,
the elf have more than one section, we need to decode it first and
packed them into u-boot.itb with its file. This script is to generate
the its script.
Need default bl31.elf in root directory of U-Boot source and dtb
as parameter.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Only rk3399 atf need ROCKCHIP_SPL_RESERVE_IRAM. This commit updates
its default setting to 0 so that other SoCs do not need to define it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
