summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2017-09-18rockchip: dts: rk3399-puma: replace 'rockchip, vbus-gpio' with fixed regulatorPhilipp Tomsich
On the RK3399-Q7, we need to turn on the on-module USB hub before using the USB host interfaces (only the OTG interface is directly connected to the edge connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses a fixed regulator to turn on the USB hub. References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus" Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rk3288: Add Vyasa initial board supportJagan Teki
This patch adds support for Vyasa RK3288 initial board from Amarula Solutions. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk3399: spl: remove hard-coded addresses for GRF and SGRFPhilipp Tomsich
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL enabled: this allows the use of syscon to retrieve the addresses of GRF and SGRF (except for the early debug UART setup, which runs so early that the device-model is not initialised). This removes the hard-coded addresses and goes through syscon to retrieve the base-addresses of GRF and SGRF. After that, we use the structure definitions to locate the respective registers. In addition to this, the inclusion of header files is also cleaned up: - all headers are included at the beginning (there was a spurious inclusion of the grf header from within a function) - all #include statements for unused headers are removed - the remaining #include statements are sorted (while keeping common.h included in front) Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: dts: rk3368-lion: add /chosen/tick-timerPhilipp Tomsich
To support bootstage recording, we want to mark our DM timer as the tick-timer; this triggers the support for 'trying harder' to read the timer in the Rockchip DM timer driver, even if the device model isn't ready yet. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk322x: Disable integrated macphy for saving power consumingDavid Wu
Unfortunately, the integrated macphy default is enabled, which will increase power consuming, if we do not use this PHY. So let's disable it at first, which will save power consuming. If we really use it, then enable it in driver level. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk322x: enable fastboot to set boot mode tagKever Yang
To support fastboot "fastboot reboot-bootloader" cmd. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18ARM: dts: rockchip: add USB nodes for evb-rv1108William Wu
This patch adds USB OTG/EHCI/OHCI nodes for evb-rv1108 USB ports. Signed-off-by: William Wu <william.wu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18imx: imx7d: remove CamelCase from ENET_xMHz macrosEric Nelson
Update these macros to use all upper-case to avoid checkpatch warnings: ENET_25MHz, ENET_50MHz, ENET_125MHz, Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-18imx_common: detect USB serial downloader reliablyStefan Agner
The current mechanism using SCR/GPR registers work well when the serial downloader boot mode has been selected explicitly (either via boot mode pins or using bmode command). However, in case the system entered boot ROM due to unbootable primary boot devices (e.g. empty eMMC), the SPL fails to detect that it has been downloaded through serial loader and tries to continue booting from eMMC: Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### The only known way to reliably detect USB serial downloader is by checking the USB PHY receiver block power state... Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18imx: add macro to detect whether USB PHY is activeStefan Agner
This macro allows to detect whether the USB PHY is active. This is helpful to detect if the boot ROM has previously started the USB serial downloader. The idea is taken from the mfgtool support in the NXP U-Boot: http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412 Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18ARM: uniphier: add GPU(Mali) reset deassert and clk enableMasahiro Yamada
The driver for Linux is out of control of Socionext, so set up reset / clock in here. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18ARM: uniphier: remove bit field macros from sc64-regs.hMasahiro Yamada
Starting from PXs3, the bit fields of RSTCTRL, CLKCTRL registers will change every SoC. There is no more point to define bitfields in the common header file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18ARM: uniphier: merge two defconfig files into uniphier_v7_defconfigMasahiro Yamada
The main difference between Pro4 and PXs2/LD6b is the Denali NAND IP version. This is now distinguished by DT. Merge the two defconfig files into uniphier_v7_defconfig. Update the README.uniphier too. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-15ARM: davinci: Remove CONFIG_SOC_DA830Adam Ford
Nothing CONFIG_SOC_DA830 anymore, so let's remove it and the one remaining source file for it. It appears to have been abandoned a while ago. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-15arm: dts: Add missing u-boot specific dtsi for dra7-evmJean-Jacques Hiblot
commit b63b995 (arm: dts: Add u-boot specific compatibles) separated out u-boot specific compatibles from dts files. The u-boot specifics were moved in *-u-boot.dtsi files for all dra7 platforms except dra7-evm. Without it the SD card is broken on DRA7-evm because the regulator cannot be enabled. Fix it by adding the missing dra7-evm-u-boot.dtsi with the needed properties. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-15arm: mach-omap2: Relax checks on OP-TEE location to allow pageable imageHarinarayan Bhatta
When the OP-TEE image is built for secure paging the load address may be in SRAM, remove checks that prevent this. Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-15blk: Remove various places that do flush cache after readBin Meng
All these places seem to inherit the codes from the MMC driver where a FIXME was put in the comment. However the correct operation after read should be cache invalidate, not flush. The underlying drivers should be responsible for the cache operation. Remove these codes completely. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: York Sun <york.sun@nxp.com>
2017-09-14ARM: DRA7: Cleanup old pinctrl macrosSuman Anna
Commit 6ae4c3efbd62 ("ARM: DRA7: Add pinctrl register definitions") has added new macros for pinmux configuration in line with the kernel definitions. Cleanup the old pinctrl macros from the common header file so that they are not used by any new boards. Signed-off-by: Suman Anna <s-anna@ti.com>
2017-09-14ARM: at91: spl: Add macro CONFIG_XXXX_BOOT supportWenyou Yang
Use the CONFIG_XXXX_BOOT to indicate the boot media, instead of the CONFIG_SYS_USE_XXXX option, which is declared by CONFIG_SYS_EXTRA_OPTIONS option. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14ARM: at91: Remove hardware.h included in configsWenyou Yang
As said in READRE.kconfig, include/configs/*.h will be removed after all options are switched to Kconfig. As the first step, remove the follow line from include/configs/*.h. #include <asm/hardware.h> Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14ARM: at91: Add the SoC options to KconfigWenyou Yang
To prepare to remove the SoCs options such as SAMA5D2, SAMA5D3 and SAMA5D4 from the CONFIG_SYS_EXTRA_OPTIONS option which is deprecated, add the SoC options to Kconfig. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14ARM: at91: Move CONFIG_AT91FAMILY option to KconfigWenyou Yang
Move the CONFIG_AT91FAMILY option from include/mach/<soc>.h header file to Kconfig. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14board: atmel: Add SAMA5D27 SOM1 EK boardWenyou Yang
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2 with 1Gbit DDR2-SDRAM in a single package. The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and Mac-address EEPROM. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: at91: Get the Chip ID of SAMA5D2 SiPWenyou Yang
The SAMA5D2 SiP(System in Package) has different Chip IDs in the CHIPID and CHIP_EXID registers. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: at91: mach: Add missing defines of MPDDRCWenyou Yang
Add missing defines of Multiport DDR-SDRAM Controller (MPDDRC). Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: at91: spl: Add boot device for boot from QSPIWenyou Yang
Add the boot device for booting from the QSPI flash. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: at91: spl: Add mck function to lower rate while switchingWenyou Yang
Refer to the commit 70f8c8316ad(PMC: add new mck function to lower rate while switching) from AT91Bootstrap. While switching to a lower clock source, we must switch the clock source first instead of last. Otherwise, we could end up with too high frequency on internal bus and peripherals. This happens on SAMA5D2 as exitting from the ROM code. Add a function pmc_mck_init_down() to allow this sequence. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: at91: spl: Adjust switching to oscillator for SAMA5D2Wenyou Yang
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to the crystal oscillator, a check must be carried out to ensure that the oscillator is present and that its freqency is valid. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14atmel: common: Add function to display via DM_VIDEO's APIWenyou Yang
Add a function to display the company's logo and board information via the API from DM_VIDEO. This function can be shared by other atmel boards, so locate it in board/atmel/common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14ARM: dts: at91: sama5: Add the sfr nodeWenyou Yang
For sama5d2, add the sfr node with syscon support. In order to access the SFR_UTMICKTRIM register for the utmi clock driver, add the phandle property for the utmi node to point to the sfr node. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14clk: at91: utmi: Set the reference clock frequencyWenyou Yang
By default, it is assumed that the UTMI clock is generated from a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ field of the SFR_UTMICKTRIM has to be updated to generate the UTMI clock in the proper way. The UTMI clock has a fixed rate of 480 MHz. In fact, there is no multiplier we can configure. The multiplier is managed internally, depending on the reference clock frequency, to achieve the target of 480 MHz. The patch is cloned from the patch of mailing-list: [PATCH v2] clk: at91: utmi: set the mainck rate Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> [trini: Depend on SPL_DM] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-13Convert CONFIG_EMIF4 et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_EMIF4 CONFIG_SDRC Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-13arm: dts: omap3: Re-sync DTS files with Linux 4.13-RC5Adam Ford
The DTS files had some spacing issues and they needed fixing. This pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5. To keep the DTS and DTSI files clean and in sync with Linux, new u-boot.dtsi files are added. Signed-off-by: Adam Ford <aford173@gmail.com> V3: The resync broke card detect on MMC1 on Logic PD's Torpedo, so we add the cd-invert to the Torpedo's -u-boot.dtsi file. V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo Remove the need for the second patch in the series
2017-09-13ARM: dts: ethernut5: Fix the build warningWenyou Yang
Fix the building warning as below: ---8<---- Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50 Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50 --->8---- Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-12ARM: DRA72x: Add support for detection of DRA71x SR 2.1Vishal Mahaveer
DRA71x processors are reduced pin and software compatible derivative of DRA72 processors. Add support for detection of SR2.1 version of DRA71x family of processors. Signed-off-by: Vishal Mahaveer <vishalm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-12dma: import linux/dma-direction.h to consolidate enum dma_data_directionMasahiro Yamada
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete duplicated definitions of enum dma_data_direction. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-09-12armv8: mmu: add space around operatorAndy Yan
Add space around operator "+", make it match the coding style. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12armv8: mmu: remove unused macro definitionAndy Yan
Macro VA_BITS and PTE_BLOCK_BITS are not used in the code, so remove them. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12ARM: rmobile: dts: Add XHCI USB node to r8a7796Marek Vasut
The R8A7796 XHCI USB nodes are missing from r8a7796 dtsi, add them. These nodes don't come from mainline Linux, yet the DT binding is similar enough to R8A7795 which already has those in mainline and once the nodes hit mainline, this DT should be resynched. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-12ARM: rmobile: dts: Add EHCI USB nodes to r8a7796Marek Vasut
The R8A7796 EHCI USB nodes are missing from r8a7796 dtsi, add them. These nodes don't come from mainline Linux, yet the DT binding is similar enough to R8A7795 which already has those in mainline and once the nodes hit mainline, this DT should be resynched. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-12ARM: dts: rmobile: Update DTS to match Linux 4.13Marek Vasut
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.13, commit 569dbb88e80deb68974ef6fdd6a13edb9d686261 . This includes both M3 and H3 ULCB and Salvator-X boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-09-12Merge git://git.denx.de/u-boot-dmTom Rini
2017-09-11dm: core: Add ofnode_for_each_subnode()Simon Glass
Add a convenience macro to iterate over subnodes of a node. Make use of this where appropriate in the code. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-09-11board: sama5d4_xplained: Set mac address from eepromWenyou Yang
Add the code to set the ethernet mac address from eeprom by using the common code from the common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: sama5d2_xplained: Replace code to set mac addressWenyou Yang
Replace the code to set the ethernet mac address with the code from the common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: atmel: Create board/$(VENDOR)/common folderWenyou Yang
Create board/$(VENDOR)/common folder to accommodate the common code shared by other atmel boards, now put the code to set ethernet mac address from eeprom, which uses the i2c eeprom driver. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: ti: am57xx: Add dt support for BeagleBoard-X15 revCLokesh Vutla
Add support for selecting proper dtb for am57xx BeagleBoard X15 revC u-boot from FIT Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11board: ti: am571x: Add 666MHz support for AM571x IDKSteve Kipisz
AM571x supports DDR running at 666MHz. Right now it is clocked at 532MHz which is lower than what is supported. In order to have maximum performance on AM571-IDK, switch DDR to 666MHz. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11board: ti: dra76: Add dt supportLokesh Vutla
Add support for selecting proper dtb for dra76x u-boot from FIT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-01-09 22:30:22 +0000