summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2019-04-25colibri_vf: fix ethernet by adding explicit phy nodeMarcel Ziswiler
The implicit fallback mechanism for searching the whole MDIO bus for at least one PHY has been gone with the following commit b882005a18de ("drivers/net/fec: phy_init: remove redundant logic"). This lead to the Ethernet driver erroring out as follows: Net: Could not get PHY for FEC0: addr -19 eth-1: fec@400d1000 Colibri VFxx # dhcp Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 No ethernet found. Could not get PHY for FEC0: addr -19 Colibri VFxx # This commit adds an explicit PHY node which makes it work again. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25imx: support i.MX8QM MEK boardPeng Fan
Add i.MX8QM MEK board support. Included a basic dts, enabled SPL FIT Boot log as below: U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) Normal Boot Trying to boot from MMC2_2 U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) CPU: NXP i.MX8QM RevB A53 at 142933 MHz Model: Freescale i.MX8QM MEK Board: iMX8QM MEK Build: SCFW 9330215b Boot: SD1 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: Error: ethernet@5b040000 address not set. eth-1: ethernet@5b040000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx8: imx8-pins: add i.MX8QMPeng Fan
Add i.MX8QM entry Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx8: add cpu supportPeng Fan
Add cpu type and Kconfig entry Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25arm: dts: introduce dtsi for i.MX8QMPeng Fan
Introduce basic dtsi for i.MX8QM, only support SDHC/FEC/LPUART. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25ARM: defconfig: kp_imx53: Enable DM_USB support on HSC|DDC boardsLukasz Majewski
This commit enables the DM_USB on HSC|DDC i.MX53 based boards. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Enable USB host support (including regulators) on HSC|DDC boardsLukasz Majewski
This commit enables the support for K&P's HSC|DDC imx53 based boards. It was also necessary to provide device tree description for regulators to avoid board specific code definition. The GPIO pin description responsible for VBUS control has been moved from "hog" group to usbh1 dedicated one. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Provide USB host DTS description for i.MX53 devicesLukasz Majewski
This code has been ported from Linux kernel - tag v5.1-rc2. The difference from the kernel is the removal of: fsl,usbmisc = <&usbmisc 1>; fsl,usbphy = <&usbphy1>; properties, which are not needed for correct u-boot operation (as PHY setup is done in ehci-mx5.c file itself). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Enable CONFIG_DM_MMC and CONFIG_DM_BLK on HSC and DDC boardsLukasz Majewski
This commit enables DM_MMC and DM_BLK on imx53 based HSC and DDC boards. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Add esdhc3 device tree description tuning for HSC|DDC boardsLukasz Majewski
In this commit the esdhc3 controller is enabled as well as it is remaped to mmc0 to not break legacy code. The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file definition. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25imx8qxp: mek: enable dm-spl for pmPeng Fan
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled, the bind and probe code in board file could be removed. Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx: sip: add call_imx_sip_ret2Peng Fan
This function will be used by i.MX8 fuse driver. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25arm: socfpga: mailbox: Fix off-by-one error on command length checkingLey Foon Tan
A mailbox command contains 1-u32 header + arguments. The "len" variable only contains the length of the arguments, but not the 1-u32 header. Include the length of header when checking the ring buffer space to prevent off-by-one error. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2019-04-25arm: socfpga: gen5: reduce SPL pre-reloc mallocSimon Goldschmidt
By enabling debug prints in malloc_simple, we can see that SPL for socfpga gen5 does by far not need the 8 KiB malloc pool currently allocated for SPL in pre-reloc phase. On socfpga_socrates, 1304 bytes are currently used (and this increases by ~200 bytes only for the sdram/reset fixes in socfpga-next). To prevent wasting precious SRAM space, let's reduce the initial heap used for SPL to 2 KiB. This is still some hundred bytes more than currently used. Also, the gen5 SPL enables stack and heap in DDR memory pretty early. Only the initial uclass/dm parsing, serial console and DDR initialization is done in the initial heap, so these 2 KiB should be enough for all boards. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2019-04-25arm: socfpga: imply/default common config optionsSimon Goldschmidt
This commit moves common config options used in all socfpga boards to select/imply in Kconfig. This both cleans up the defconfig files as well as makes future changes easier. Options implied/defaulted for all sub-arches: - SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS Options implied/defaulted for implied for A10 & gen5: - FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE Options implied/defaulted for gen5: - SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2019-04-24Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dmTom Rini
Various minor sandbox iumprovements Fixes for tracing with sandbox Refactoring for boot_get_fdt()
2019-04-24Merge tag 'u-boot-stm32-mcu-20190423' of https://github.com/pchotard/u-bootTom Rini
STM32 MCUs update: - DT rework and alignment with DT kernel v4.20 - mmc: arm_pl180_mmci: Synchronize compatible with kernel v4.20 - mmc: stm32_sdmmc2: Synchronize properties with kernel v4.20 - configs: update for F746/769 boards
2019-04-24Merge tag 'u-boot-amlogic-20190423' of git://git.denx.de/u-boot-amlogicTom Rini
- Add support for Amlogic p200 & p201 Reference Designs - Add Amlogic SoC information display - Add support for the Libretech-AC AML-S805X-AC board - Add Amlogic AXG reset compatible - Add I2C support for Amlogic AXG - Fix AXG PIN and BANK pinctrl definitions - Fix regmap_read_poll_timeout warning about sandbox_timer_add_offset - Add initial support for Amlogic G12A SoC and U200 board - Enable PHY_REALTEK for selected boards - Fix Khadas VIM2 README
2019-04-23dm: core: Change platform specific translation-offset handlingStefan Roese
Testing has shown that the current DM implementation of a platform / board specific translation offset, as its needed for the SPL on MVEBU platforms is buggy. The translation offset is confingured too late, after the driver bind functions are run. This may result in incorrect address translations. With the current implementation its not possible to configure the offset earlier, as the DM code has not run at all. This patch now removed the set_/get_translation_offset() calls and moves the translation offset into the GD variable translation_offset. This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled. This option is enabled only for MVEBU on ARM32 platforms, where its currenty needed and configured in the SPL. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pierre Bourdon <delroth@gmail.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Tested-by: Pierre Bourdon <delroth@gmail.com> Tested-by: Baruch Siach <baruch@tkos.co.il>
2019-04-23ARMv8: PSCI: Fix PSCI_TABLE relocation issueLars Povlsen
This fixes relaction isses with the PSCI_TABLE entries in the psci_32_table and psci_64_table. When using 32-bit adress pointers relocation was not being applied to the tables, causing PSCI handlers to point to the un-relocated code area. By using 64-bit data relocation is properly applied. The handlers are thus in the "secure data" area, which is protected by /memreserve/ in the FDT. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
2019-04-23ARM: MediaTek: Add support for MT8516 SoCFabien Parent
Add support for MediaTek MT8516 SoC. This include the file that will initialize the SoC after boot and its device tree. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-23poplar: enable Ethernet driver supportShawn Guo
The 'phy' reset of gmac device in kernel device tree is not generic enough for u-boot to use, so we need to overwrite the 'resets' property as needed. With this device tree fixup and poplar_defconfig changes, Ethernet starts working on Poplar board. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-23dt: bcm963158: enable led controllerPhilippe Reynes
Enable the led controller in the device tree of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-23dt: bcm63158: add led controllerPhilippe Reynes
Add the led controller in the bcm63158 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-23dt: bcm968580xref: enable led controllerPhilippe Reynes
Enable the led controller in the device tree of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-23ARM: dts: stm32: Update sdmmc binding for stm32mp157c-ed1Patrice Chotard
Update some sdmmc properties which have been updated with v4.19 DT bindings: - st,dirpol becomes st,sig-dir - st,negedge becomes st,neg-edge - st,pin-ckin becomes st,use-ckin Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Update sdmmc binding for stm32h743i-evalPatrice Chotard
Update some sdmmc properties which have been updated with v4.19 DT bindings: - st,dirpol becomes st,sig-dir - st,negedge becomes st,neg-edge - st,pin-ckin becomes st,use-ckin Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Restore old usart1 clock bindings for stm32f7Patrice Chotard
As U-boot stm32f clock driver doesn't support new bindings for auxiliary clocks (clocks = <&rcc 1 ....>), restore old bindings for usart1 to get console output. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Sync DT with v4.20 kernel for stm32h7Patrice Chotard
Synchronize stm32h7 device tree with kernel v4.20. U-boot DT files and pinctrl bindings are updated, useless nodes are removed and gpio compatible added. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: Migrate U-boot nodes to U-boot DT files for stm32h7Patrice Chotard
In order to prepare and ease future DT synchronization with kernel DT, migrate all U-boot specific nodes/properties/addons to U-boot DT files. As sdmmc is not yet supported on kernel side, sdmmc nodes are located in eval-u-boot and disco-u-boot DT files. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Sync DT with v4.20 kernel for stm32f7Patrice Chotard
Synchronize stm32f7 device tree with kernel v4.20. All pinctrl bindings are updated. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Migrate U-boot nodes to U-boot DT files for stm32f7Patrice Chotard
In order to prepare and ease future DT synchronization with kernel DT, migrate all U-boot specific nodes/properties/addons to U-boot DT files. Migrate also DT nodes which are not yet available on kernel DT side as ethernet, ltdc and qspi nodes. Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: stm32: Sync DT files with v4.20 kernel for stm32f4Patrice Chotard
Synchronize stm32f7 device tree with kernel v4.20. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM:dts: stm32: sort nodes by alphabetical order in f4 u-boot filesPatrice Chotard
Sort nodes alphabetically to be coherent with all others STM32 DT files. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23ARM: dts: Import Amlogic G12A u200 DT from Linux 5.1-rc1Neil Armstrong
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23ARM: meson: add G12a supportJerome Brunet
Add support for the Amlogic G12A SoC, which is a mix between the new physical memory mapping of AXG and the functionnalities of the previous Amlogic GXL/GXM SoCs. To handle the internal ethernet PHY, the Amlogic G12A SoCs now embeds a dedicated PLL to feed the internal PHY. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23clk: meson: add g12a supportJerome Brunet
Add basic support for the Amlogic G12A clock controller based on the AXG driver. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-22dt: bcm6858: add led controllerPhilippe Reynes
Add the led controller in the bcm6858 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22arm: arm64 32bit address relocationIbai Erkiaga
Current relocation code is limited to 21bit PC-relative addressing which might not be enough for bigger code sizes. The following patch increases the addressing to 32bit PC-relative. This feature is specially interesting if U-Boot is build without optimiation (-O0) as the text section is increased significativelly. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
2019-04-22arm: fix hvc callIbai Erkiaga
HVC call makes use of 6 mandatory arguments rather than 7 in the same way as SMC calls. The 7th argument is optional (Client ID) for both HVC and SMC but is implemented as 16-bit parameter and register R7 or W7. The aim of this patch is just fix compilation error due to an invalid asm code in the HVC call so that's why the 7th argument is removed. The issue does not report any error in a normal build as hvc_call is not used at all and is optimized by the compiler. Using -O0 triggers the error so the patch is intended to fix issues on a ongoing effor to build U-Boot with -O0. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
2019-04-22ARMv8: Disable fwcall when PSCI is enabledAng, Chee Hong
When PSCI is enabled, we are expecting U-Boot which now act as EL3 software will handle all the PSCI calls. We won't need fwcall as no further HVC or SMC are needed. Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
2019-04-22ARMv8: Allow SiP service extensions on top of PSCI codeChee Hong Ang
Allow PSCI layer to handle any SiP service functions added by platform vendors. PSCI layer will look for SiP service function in the SiP function table located in '._secure_svc_tbl_entries' section if the SMC function identifier is not found in the PSCI standard functions table. Use DECLARE_SECURE_SVC macro to declare and add platform specific SiP service function. This new section '._secure_svc_tbl_entries' is located next to '._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2019-04-22dt: bcm963158: enable nand controllerPhilippe Reynes
Enable the nand controller in the device tree of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22dt: bcm63158: add nand controllerPhilippe Reynes
Add the nand controller in the bcm63158 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22dt: bcm968580xref: enable nand controllerPhilippe Reynes
Enable the nand controller in the device tree of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22dt: bcm6858: add nand controllerPhilippe Reynes
Add the nand controller in the bcm6858 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22arm: asm: io.h: define readX_relaxed and writeX_relaxedPhilippe Reynes
This patch port the function readX_relaxed and writeX_relaxed from kernel 4.18. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmelTom Rini
Second set of u-boot-atmel features and fixes for 2019.07 cycle
2019-04-21Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Various fastboot, dwc2/stm32 updates
2019-04-21Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Various stratix10, gen5 updates