summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2019-01-28mx7: Do not call lcdif_power_down() in the SPL caseFabio Estevam
Like it was done on imx6 in commit 9236269de57d ("imx: mx6: Fix implementantion reset_misc") Do not call lcdif_power_down() in the SPL case to fix the following build error: LD spl/u-boot-spl MKIMAGE u-boot.img arch/arm/mach-imx/built-in.o: In function `reset_misc': /home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down' scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: Add PHYTEC phyBOARD-i.MX6UL-SeginMartyn Welch
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063). CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Board: PHYTEC phyCORE-i.MX6UL I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC0 Working: - Eth0 - i2C - MMC/SD - NAND - UART (1 & 5) - USB (host & otg) Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-01-28imx: hab: Convert non-NULL IVT DCD pointer warning to an errorBreno Matheus Lima
The following NXP application notes and manual recommend to ensure the IVT DCD pointer is Null prior to calling HAB API authenticate_image() function: - AN12263: HABv4 RVT Guidelines and Recommendations - AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using HABv4 - CST docs: High Assurance Boot Version 4 Application Programming Interface Reference Manual Commit ca89df7dd46f ("imx: hab: Convert DCD non-NULL error to warning") converted DCD non-NULL error to warning due to the lack of documentation at the time of first patch submission. We have warned U-Boot users since v2018.03, and it makes sense now to follow the NXP recommendation to ensure the IVT DCD pointer is Null. DCD commands should only be present in the initial boot image loaded by the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error if a DCD pointer is present in an image being authenticated by calling the HAB RVT API. Older versions of HAB will process and run DCD if it is present, and this could lead to an incorrect authentication boot flow. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-01-26linker: Modify linker scripts to be more genericTom Rini
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the same script for both SPL and TPL. Add logic to scripts/Makefile.spl to pass in the right value when preprocessing the script. Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jagan Teki <jagan@openedev.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-01-26rockchip: Add TPL_MAX_SIZE for RK3288Tom Rini
Per Kever Yang, 32768 is a reasonable max size for TPL on RK3288. Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-01-26ARM: mach-omap2: Kconfig: Allow OMAP5 devices to set entry pointAndrew F. Davis
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to have an non-standard boot address in memory. This may be due to the device being a high security variant, which place the Initial SoftWare (ISW) after certificates and secure software. Allow these devices to set this from Kconfig. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-01-26spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFUAndrew F. Davis
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT to allow for cleaner use in code. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26arm64: dt: poplar: add optee nodeIgor Opaniuk
As Poplar supports running TF-A with OP-TEE as BL32 payload, add op-tee node in DT, which enables usage of OP-TEE driver (which provides an interface for requesting services from OP-TEE). Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-25poplar: clean up board level mmc initialization codeShawn Guo
We have converted mmc to driver model on Poplar. So let's clean up board level mmc initialization code. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-01-25poplar: sync up device tree with kernel 4.20Shawn Guo
It adds missing pinctrl headers, updates clock header and sync up Poplar device tree with kernel 4.20 release. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2019-01-25dts: 820c: Add pinctrl node and uart muxRamon Fried
* Add pinctrl node for TLMM and add mux request for uart node. * Rename uart to the actual board uart port. * Fix indentendation of sdhc2 node. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-25arm: mach-snapdragon: pinctrl: clarify gpio disable bitRamon Fried
The TLMM_GPIO_ENABLE bit is actually use to disable the GPIO. change it to TLMM_GPIO_DISABLE so it's clearer. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-25arm: mach-snapdragon: add pinctrl driver for db820cRamon Fried
Add pinctrl driver for Dragonboard820c, currently with only one mux func to initialize pins for serial console. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-25arm: mach-snapdragon: db820c: Actually init PLL for serialRamon Fried
The PLL for the UART was not set, and relied on previous initializtion made by LK. add the appropriate initialization. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-25arm: stm32mp1: deploy spl in root folderSean Nyekjær
Deploy u-boot-spl.stm32 binary in u-boot root folder like the rest of the boards. This makes it more streamlined when building in Yocto, Buildroot etc.. Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
2019-01-24Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-01-24ARM: zynq: Remove unused GEM addressesMichal Simek
With DM in place there is no need to have GEM addresses in headers. None is using them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Remove unused GEM addressesMichal Simek
With DM in place there is no need to have GEM addresses in headers. None is using them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24zynq: Kconfig: extend the bootstrap malloc() poolAnton Gerasimov
Most of the memory is being consumed by device binding code, more space needed for other data structures. Z-turn board has already hit the limit, others may follow soon. Measuring only the memory consumed in device_bind_common, I've got the following results (in decimal): root_driver: 108 mod_exp_sw: 108 amba: 120 serial@e0000000 aka uart0: 112 serial@e0001000 aka uart1: 88 spi@e000d000 aka qspi: 120 sdhci@e0100000 aka mmc0: 455 sdhci@e0100000.blk: 208 slcr@f8000000: 96 clkc@100: 72 (total) 1487 = 0x5cf of 0x600 Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24topic-miamiplus: Run CPU at 800MHz for speedgrade-2Mike Looijmans
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz. Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Move SoC sources to mach-zynqmpMichal Simek
Similar changes was done for Zynq in past and this patch just follow this pattern to separate cpu code from SoC code. Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/* And also fix references to these files. Based on "ARM: zynq: move SoC sources to mach-zynq" (sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup proper SPI dependencyMichal Simek
Select DM_SPI/DM_SPI_FLASH for the whole SoC. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24ARM: zynqmp_r5: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: versal: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Fix mmc node names to be in sync with kernelSiva Durga Prasad Paladugu
This patches renames sd nodes in dts to be in line with kernel. This patch also modifies the references for the same in code. It checks mmc first to have no time penalty for new DT node names based on left-to-right expression evaluation. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Do not protect zynqmp_pmufw_version()Michal Simek
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version() but also FPGA code is calling this function which is possible to use without actual CLK_ZYNQMP firmware driver to be enabled. This patch enables the case where only fixed-clock CLK setup is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-21ARM: mvebu: add support for Allied Telesis x530Chris Packham
This is a range of stackable network switches. The SoC is Armada-385 and there are a number of variants with differing network port configurations. The DP variants are intended for a harsher operating environment so they use a different i2c mux and fit industrial-temp parts. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm64: dts: marvell: armada-ap806: reserve PSCI areaHeinrich Schuchardt
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any attempt to access it from U-Boot leads to an immediate crash. So let's make the same memory reservation as the vendor device tree. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Support 1 GB version of Turris MoxMarek Behún
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB or 1 GiB. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: dts: Fix Turris Mox device treeMarek Behún
DTC issues a warning because #address-cells and #size-cells properties are not set in the mdio node. Also add ethernet1 alias. Also add RTC node. Also fix USB3 regulator startup delay time. Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the speed value is not used byt the comphy driver for PCI Express, but should be 5 GHz nonetheless). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Check and configure modulesMarek Behún
Check if Mox modules are connected in supported mode, then configure the MDIO addresses of switch modules. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21ARM: mvebu: sync Armada-38x dts with Linux 4.20Chris Packham
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes not taken are new compatible strings for the uart and nand flash controller. The nand binding is best updated if/when the mtd/nand infrastructure is updated. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-18Merge tag 'fsl-qoriq-for-v2019.04-rc1' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Add TFA boot flow for more boards Add TFA boot defconfig for ls1088a and ls2088a. Add dts fixup for PCIe endpoint and root complex.
2019-01-18arm: dts: am335x-pdu001: Sync with Linux 5.0-rc2Felix Brack
This patch synchronizes the PDU001 board DTS file with the one used by Linux 5.0-rc2. Signed-off-by: Felix Brack <fb@ltec.ch>
2019-01-18arm: sunxi: Enable CLK, RESETJagan Teki
CLK and DM_RESET drivers are now available for all of the Allwinner platforms, so enable them in arch/arm/Kconfig Enabling CLK will select DM_RESET by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18ARM: dts: sun8i: Update A80 dts(i) from Linux-v4.18-rc3Jagan Teki
Update all A80 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commits. arch/arm/boot/dts/sun9i-a80*: commit 190e3138f9577885691540dca59c2f07540bde04 Merge: cafc87023b0d a7affb13b271 Author: Arnd Bergmann <arnd@arndb.de> Date: Tue Mar 27 14:58:00 2018 +0200 Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt include/dt-bindings/*/sun9i-a80-*: commit 783ab76ae553abc23f80ef7511052d055697531b Author: Chen-Yu Tsai <wens@csie.org> Date: Sat Jan 28 20:22:36 2017 +0800 clk: sunxi-ng: Add A80 Display Engine CCU Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same dts is not available in Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18reset: Add Allwinner RESET driverJagan Teki
Add common reset driver for all Allwinner SoC's. Since CLK and RESET share common DT compatible, it is CLK driver job is to bind the reset driver. So add CLK bind call on respective SoC driver by passing ccu map descriptor so-that reset deassert, deassert operations held based on ccu reset table defined from CLK driver. Select DM_RESET via CLK_SUNXI, this make hidden section of RESET since CLK and RESET share common DT compatible and code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: Add Allwinner A64 CLK driverJagan Teki
Add initial clock driver for Allwinner A64. Implement USB clock enable and disable functions for OHCI, EHCI, OTG and USBPHY gate and clock registers via ccu clk gate table. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18board: sun50i-h5: Add Emlid Neutis N5 supportAleksandr Aleksandrov
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT module, DDR3 RAM and eMMC. - add neutis-devboard target to dtb makefile - add dtsi file for Neutis N5 needs - add config file for Neutis N5 Dev board Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> [jagan: update proper commit head] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18sunxi: board: Add i2c initialization for sun50iStefan Mavrodiev
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE. However even the controller is enabled, the mux for the pins are not set. This patch follows the existing mux method. Since the pads are different, separate check is added for each i2c. Tested with A64-SOM204 board. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-01-18arm: Kconfig: spelling fixesChris Packham
Signed-off-by: Chris Packham <judge.packham@gmail.com>
2019-01-18mach-snapdragon: db410: pinctrl: fix pin countRamon Fried
Pin count in APQ8016 was wrong, fix that. Fixes: ad97051b7ff6 ("mach-snapdragon: Introduce pinctrl driver") Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-18dts: db410: fix indentationRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-01-17armv7: dts: ls1021a: Remove aliases property name warningRajesh Bhagat
Remove aliases property name warning while compilation: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-' Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: fsl-layerscape: properly configure qdma ICIDLaurentiu Tudor
The ICIDs for the qdma device are not configured through SCFG but through some registers found in the actual device register block. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1043a: correct the PCIe INTx fixupHou Zhiqiang
On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on rev1.1 there is only 1 for INTx, so the current fixup is inverse of the fact. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1043a: add SVR definitions for 23x23 package siliconHou Zhiqiang
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls2088ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls2088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - remove EL3 specific erratas for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1088ardb: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-29 02:15:18 +0000