summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2018-12-07gpio: stm32f7: Move STM32_GPIOS_PER_BANK into gpio.hPatrice Chotard
To allow access to this define by other driver, move it into gpio.h Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-07gpio: stm32f7: Add gpio bank holes managementPatrice Chotard
In some STM32 SoC packages, GPIO bank has not always 16 gpios. Several cases can occur, gpio hole can be located at the beginning, middle or end of the gpio bank or a combination of these 3 configurations. For that, gpio bindings offer the gpio-ranges DT property which described the gpio bank mapping. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-07serial: bcm6858: remove driver and switch to bcm6345Álvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-12-07arm: implement {in, out}_{16, 32} and {clr, set, clrset}bits_{16, 32}Álvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-12-07arm: am335x-pdu001: Enable CONFIG_BLK and CONFIG_DM_MMCFelix Brack
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001 board. It depends on Patrice Chotard's patch 'power: regulator: denied disable on always-on regulator' which prevents power cycling the vmmc supply. Without this patch the board will not boot as vmmc is unfortunately used by other board components, not just eMMC and micro SD card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card detection input' is required to boot from external micro SD card. Without this patch no SD card will be detected and hence booting will fail. Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-07dts: am335x-pdu001: Fix polarity of card detection inputFelix Brack
When a micro SD card is inserted in the PDU001 card cage, the card detection switch is opened and the corresponding GPIO input is driven by a pull-up. Hence change the active level of the card detection input from low to high. Signed-off-by: Felix Brack <fb@ltec.ch>
2018-12-07ARM: at91: lds: add test for SPL binary size and bss sizeEugen.Hristev@microchip.com
Add test for the SPL binary size and the bss section size. This will throw an error at build time if the SPL sections do not fit in the designated RAM area, thus avoiding oversizing the SPL. Based on original work by Wenyou Yang. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-12-06pinctrl: stm32: make pinctrl use hwspinlockBenjamin Gaignard
Protect configuration registers with a hardware spinlock. If a hwspinlock is defined in the device-tree node used it to be sure that none of the others processors on the SoC could change the configuration at the same time. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-06hwspinlock: add stm32 hardware spinlock supportBenjamin Gaignard
Implement hardware spinlock support for STM32MP1. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-06armv8: lx2160a: Add LX2160A SoC SupportPriyanka Jain
LX2160A Soc is based on Layerscape Chassis Generation 3.2 architecture with features: 16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC, 2 64-bit DDR4 memory controller, RGMII, 8 I2C controllers, 3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs, 4 TZASC instances, etc. SoC personalites: LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8:fsl-layerscape: Add support for Chassis 3.2Priyanka Jain
NXP layerscape architecture Chassis 3.2 builds upon chassis3 architecture with changes like DDR Memory map change, removal of IFC and support of upto 8 I2C controller. Patch add README.lsch3_2 and the above changes under macro CONFIG_NXP_LSCH3_2. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: lsch3: Add support of serdes3 modulePriyanka Jain
Some lsch3 based SoCs like lx2160a contains three serdes modules. Add support for third serdes protocol in lsch3 Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: dts: fsl-ls2080a: add sata node supportPeng Ma
One ls2080a, there is one SATA 3.0 advanced host controller interface which is a high-performance SATA solution that delivers comprehensive and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA capabilities, in accordance with the serial ATA revision 3.0 of Serial ATA International Organization. Add sata node to support this feature. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: dts: fsl-ls1088a: add sata node supportPeng Ma
One ls1088a, there is one SATA 3.0 advanced host controller interface which is a high-performance SATA solution that delivers comprehensive and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA capabilities, in accordance with the serial ATA revision 3.0 of Serial ATA International Organization. Add sata node to support this feature. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: dts: fsl-ls1046a: add sata node supportPeng Ma
One ls1046a, there is one SATA 3.0 advanced host controller interface which is a high-performance SATA solution that delivers comprehensive and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA capabilities, in accordance with the serial ATA revision 3.0 of Serial ATA International Organization. Add sata node to support this feature. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: add support of MC framework for TFAPankit Garg
Add support of MC framework for TFA Make MC framework independent of boot source. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: sec_firmware: return job ring status as true in TFABOOTPankit Garg
Returns job ring status as true in TFABOOT, as one job ring is always reserved. Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: sec_firmware: change el2_to_aarch32 SMC IDRajesh Bhagat
Changes the el2_to_aarch32 SMC ID from 0xc000ff04 to 0xc200ff17, it is applicable to both TFA and non-TFA boot. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: Update parsing boot sourceYork Sun
Workaround of erratum A010539 clears the RCW source field in PORSR1 register, causing failure of detecting boot source using this method. Use SMC call if U-Boot runs at EL2. If SMC is not implemented or running at EL3, continue to read PORSR1 and presume QSPI as boot source if erratum workaround A010539 is enabled and RCW source is cleared. Signed-off-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: skip OCRAM init for TFABOOTRajesh Bhagat
OCRAM initialization is performed by TFA, Hence skipped from u-boot. Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: add SMC calls for DDR size and bank infoRajesh Bhagat
Adds SMC calls for getting DDR size and bank info for TFABOOT. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: bootcmd identification for TFABOOTPankit Garg
Adds bootcmd identificaton on basis on boot source, valid in TFABOOT configuration. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> [YS: remove unnecessary braces] Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: remove EL3 specific erratas for TFABOOTRajesh Bhagat
Removes EL3 specific erratas for TFABOOT, And now taken care in TFA. ARM_ERRATA_855873, SYS_FSL_ERRATUM_A008850, SYS_FSL_ERRATUM_A008511, SYS_FSL_ERRATUM_A008336, SYS_FSL_ERRATUM_A009663, SYS_FSL_ERRATUM_A009803, SYS_FSL_ERRATUM_A009942, SYS_FSL_ERRATUM_A010165 Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: identify boot source from PORSR registerRajesh Bhagat
PORSR register holds the cfg_rcw_src field which can be used to identify boot source. Further, it can be used to select the environment location. Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [YS: fix multiple checkpatch issues] Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: Add TFABOOT supportRajesh Bhagat
Adds TFABOOT support config option and add generic code to enable execution from DDR. Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2018-12-06armv8: fsl-layerscape: change tlb base from OCRAM to DDR in EL < 3Pankit Garg
Change tlb base address from OCRAM to DDR when exception level is less than 3. Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: Enable routing SError exceptionYork Sun
In case SError happens at EL2, if SCR_EL3[EA] is not routing it to EL3, and SCR_EL3[RW] is set to aarch64, setting HCR_EL2[AMO] routes the exception to EL2. Otherwise this exception is not taken. Signed-off-by: York Sun <york.sun@nxp.com>
2018-12-06rockchip: rk3399: Add Ficus EE board supportManivannan Sadhasivam
Add board support for Ficus EE board from Vamrs. This board utilizes common Rock960 family support. Following peripherals are tested and known to work: * Gigabit Ethernet * USB 2.0 * MMC Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> [Reworked based on common Rock960 family support] Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-06rockchip: rk3399: Add Rock960 CE board supportManivannan Sadhasivam
Add board support for Rock960 CE board from Vamrs. This board utilizes common Rock960 family support. Following peripherals are tested and known to work: * USB 2.0 * MMC This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which is being used on the board. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-06rockchip: rk3399: Add common Rock960 family from VamrsManivannan Sadhasivam
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs. It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition) 96Boards. Below are some of the key differences between both Rock960 and Ficus boards: 1. Different host enable GPIO for USB 2. Different power and reset GPIO for PCI-E 3. No Ethernet port on Rock960 The common board support will be utilized by both boards. The device tree has been organized in such a way that only the properties which differ between both boards are placed in the board specific dts and the reset of the nodes are placed in common dtsi file. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> [Added instructions for SD card boot] Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2018-12-06arm: dts: rockchip: add some common pin-settings to rk3399Randy Li
Those pins would be used by many boards. Commit grabbed from Linux: commit b41023282d07b61a53e2c9b9508912b1e7ce7b4f Author: Randy Li <ayaka@soulik.info> Date: Thu Jun 21 21:32:10 2018 +0800 arm64: dts: rockchip: add some common pin-settings to rk3399 Those pins would be used by many boards. Signed-off-by: Randy Li <ayaka@soulik.info> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Randy Li <ayaka@soulik.info> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-04move data structure out of cpu.hYork Sun
Move static definitions to cpu.c file, as it doesn't allow the cpu.h file to be included in multiple c files. Signed-off-by: York Sun <york.sun@nxp.com>
2018-12-04ARM: rmobile: Set environment variable containing CPU typeMarek Vasut
Set environment variable 'platform' containing the CPU type. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-04ARM: rmobile: Enable MMC extensionsMarek Vasut
Enable extended MMC commands and GPT partition table support. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Sync Gen3 DTs with Linux 4.19.6Marek Vasut
Synchronize DTs with mainline Linux 4.19.6 , commit 96db90800c06d3fe3fa08eb6222fe201286bb778 Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Sync Gen2 DTs with Linux 4.19.6Marek Vasut
Synchronize DTs with mainline Linux 4.19.6 , commit 96db90800c06d3fe3fa08eb6222fe201286bb778 Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract i2c6 on M2W PorterMarek Vasut
The i2c6 node is missing in mainline Linux thus far, pull it into U-Boot specific DT until it hits mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract SCIF2 node on E3 EbisuMarek Vasut
The SCIF2 node is not in Linux 4.17 DTs on E3, pull it into U-Boot specific DT extras until it hits mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract SDHI nodes on E3 EbisuMarek Vasut
The SDHI nodes are not in Linux 4.17 DTs in E3, pull them into U-Boot specific DT extras until they hit mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract SDHI extras on H3, M3W, M3N Salvator-XMarek Vasut
The SDHI nodes are missing features supported in upstream U-Boot, like mode support properties. Pull the extras into U-Boot specific DT until it hits mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract SDHI extras on H3 and M3W ULCBMarek Vasut
The SDHI nodes are missing features supported in upstream U-Boot, like mode support properties. Pull the extras into U-Boot specific DT until it hits mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract CPLD node on H3 and M3W ULCBMarek Vasut
The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the node into U-Boot specific DT until it hits mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract AVB node extras on V3M EagleMarek Vasut
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the AVB node extras into U-Boot specific DT until they hit mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract SDHI nodes on M3NMarek Vasut
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot specific DT extras until they hit mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract USB nodes on M3NMarek Vasut
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot specific DT extras until they hit mainline Linux, to make syncing of DTs easier. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Extract RPC node to u-boot specific DTMarek Vasut
The RPC DT bindings are still work in progress. Extract the RPC DT node from the DT to allow easier update and so it can be replaced once the DT bindings are stable. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-04ARM: dts: rmobile: Add soc label to Gen3Marek Vasut
Add label to the /soc node, so it can be referenced from the U-Boot DTs. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> --- V2: Rebase on u-boot/master
2018-12-03Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2019.01 microblaze: - Use default functions for memory decoding - Showing model from DT zynq: - Fix spi flash DTs - Fix zynq_help_text with CONFIG_SYS_LONGHELP - Tune cse/mini configurations - Enabling cse/mini testing with current targets zynqmp: - Enable gzip SPL support - Fix chip detection logic - Tune mini configurations - DT fixes(spi-flash, models, clocks, etc) - Add support for OF_SEPARATE configurations - Enabling mini testing with current targets - Add mini mtest configuration - Some minor config setting nand: - arasan: Add subpage configuration net: - gem: Add 64bit DMA support
2018-12-03Merge tag 'signed-efi-next' of git://github.com/agraf/u-bootTom Rini
Patch queue for efi - 2018-12-03 This release is fully packed with lots of glorious improvements in UEFI land again! - Make PE images more standards compliant - Improve sandbox support - Improve correctness - Fix RISC-V execution on virt model - Honor board defined top of ram (fixes a few boards) - Imply DM USB access when distro boot is available - Code cleanups
2018-12-03Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- MMC fixes for R-Car Gen3
generated by cgit (git 2.34.1) at 2024-12-29 07:51:55 +0000