| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot. Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.
This reverts commit 22d90d560a2b01c47f180e196e6c6485eb8e65db.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The code in uniphier_sld3_sbc_init() is pin-muxing, so it would
be a better fit in uniphier_sld3_early_pin_init().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The System Bus is not available by default on the ROM boot mode of
PH1-LD20. To use devices connected to the System Bus, such as the
Micro Support Card, it is necessary to set up pin-muxing and some
System Bus Controller register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is needed to use UART on SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
PH1-LD20 does not have the dedicated boot swap select latch.
Instead, it is controlled from the boot mode select.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We are running with the caches disabled when mctl_mem_matches gets called,
but the cpu's write buffer is still there and can still get in the way,
add a memory barrier to fix this.
This avoids mctl_mem_matches always returning false in some cases, which
was resulting in:
U-Boot SPL 2015.07 (Apr 14 2016 - 18:47:26)
DRAM: 1024 MiB
U-Boot 2015.07 (Apr 14 2016 - 18:47:26 +0200) Allwinner Technology
CPU: Allwinner A23 (SUN8I)
DRAM: 512 MiB
Where 512 MiB is the right amount, but the DRAM controller would be
initialized for 1024 MiB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
This is a binding which only exists in U-Boot, but is
required to get working serial in U-Boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
PH1-LD20 does not support 1.8V signaling for SD card; only Default
Speed and High Speed (up to 50MHz) with 3.3V signaling is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is the first ARMv8 SoC from Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The current table look-up for the DTB file name turned out bothersome
in terms of maintainability; I ended up adding a new entry every time
a new board is supported.
There is a common pattern between the DT compatible string and the
corresponding file name; drop the vendor prefix "socionext," and
prefix it with "uniphier-" and suffix it with ".dtb".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
No need to stop booting U-Boot even if boot mode is unknown.
Setting the "bootmode" environment is only useful for booting
Linux Kernel. Anyway, U-Boot has already booted by this point.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For PH1-LD20 or later, per-pin input-enable control is supported,
that is, we need to set-up IECTRL registers for a group of pins.
This helper function will be useful for a bunch of register settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, fdtgrep would not accept uniphier-ph1-ld20-ref.dtb
and uniphier-ph1-ld11-ref.dtb unless the aliases node comes
the first in the root node.
$ make -s uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld20-ref
[snip]
LDS spl/u-boot-spl.lds
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Error: FDT_ERR_BADMAGIC
make[1]: *** [spl/u-boot-spl.dtb] Error 1
make: *** [spl/u-boot-spl] Error 2
This commit moves the aliases node as the error message from the
fdtgrep tool suggests, although this requirement does not sound
reasonable to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This makes the EEPROM device on the Reference Daughter board
available.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Because DT properties are 4-byte aligned, the pointer access
*(fdt64_t *) in this code causes unaligned access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
This enables full ethernet usage, including U-Boot to write the board
specific MAC address (ethaddr) into the DT blob before passing it to
Linux.
Without this, the ethaddr is not detected in U-Boot at all, resulting
in this error upon bootup:
...
Model: EBV SOCrates
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Fix a small typo in some of the SoCFPGA dts files that has spread via
copy-and-paste.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Define the UART6_BASE_ADDR for MX6UL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.
This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d
NXP errata number: ERR009219, EB821
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The echo -ne "\xNN" does not work in certain bourne-compatible shells, like
dash. The recommended way of hex->char conversion is using printf(1), but
there is a pitfall here. The GNU printf does support "\xNN" format, but
according to the opengroup documentation, this is not part of POSIX. The
POSIX printf only defines "\NNN" where N is octal. Thus, for the sake of
compatibility, we use that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The current code in ARMv8's lowlevel_init() skips the per-CPU GIC
initialization ifndef CONFIG_ARMV8_MULTIENTRY. However, the per-CPU init
should always occur; it's just the one-time init that should only happen
on the master.
Once this consideration is taken into account, the only difference between
the paths when CONFIG_ARMV8_MULTIENTRY is undefined/defined is the use of
branch_if_slave. Naively, any unified code would need to invoke this
conditionally upon ifdef CONFIG_ARMV8_MULTIENTRY. However, branch_if_slave
already checks CONFIG_ARMV8_MULTIENTRY and does nothing if it isn't
defined, so we don't even need that ifdef at the call site.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
commit 62c5674ea136a ("omap: SPL boot devices cleanup and completion")
cleans up the boot device ids for amx3xx soc. But mistakenly updates wrong
device IDs for AM43xx USB. Fixing the same here.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.
Also adding card-detect gpio for DRA74x EVM.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Move all the gpio definitions to driver file as
there is no use of them in other files.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Remove non driver model support as it moved
to driver model. Dont need non driver model
anymore.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable DM GPIO and ZYNQ GPIO using kconfig instead of the board
config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Support ZynqMP zc1751 with DC cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add new board support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There are mini configurations which need to be fit to OCM that's why
these options shouldn't be enabled by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add missing nand node for ep108.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable option to support more then 4GB memories in single size block.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use the same binding as is used in mainline Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
For run time serdes adjustment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Separate register space and put it on more lines.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
