summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2014-11-21dm: at91: Add driver model support for the serial driverSimon Glass
Add driver model support while retaining the existing legacy code. This allows the driver to support boards that have converted to driver model as well as those that have not. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21dm: at91: Add platform data for GPIO on at91sam9260-based boardsSimon Glass
These boards all have the same GPIO arrangement, so add some common platform data that can be used by all boards. Remove the configs which are no longer required. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21dm: at91: Add driver model support for atmel GPIO driverSimon Glass
Modify this driver to support driver model, with platform data required to determine the GPIOs that it controls. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-17ARM: atmel: add sama5d4 xplained ultra board supportBo Shen
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display (optional, disabled by default) - Support ethernet - Support USB mass storage Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17ARM: atmel: add sama5d4ek board supportBo Shen
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display - Support ethernet - Support USB mass storage Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, spl, at91: add spl support for the corvus boardHeiko Schocher
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91, spl: add spl support for the taurus boardHeiko Schocher
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, spl, at91: add at91sam9260 and at91sam9g45 spl supportHeiko Schocher
add support for using spl code on at91sam9260 and at91sam9g45 based boards. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> [adopt Bo's change in spl.c] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91: add missing ddr2 cr register MPDDRC_CR_EBISHARE defineHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91: compile mpddrc ram init code also for AT91SAM9M10G45Heiko Schocher
- compile mpddrc ram init code also for AT91SAM9M10G45 based boards. - in CONFIG_SAMA5D3 case, look for the ATMEL_MPDDRC_CR_DECOD_INTERLEAVED in the cr configuration Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91, mpddrc: fix typo in ddr2_init()Heiko Schocher
use the configure value for computing the ba_off value not the value from the cr register. This leaded in a wrong ram configuration on the upcoming corvus spl board support. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91: generate boot.bin file for all atmel SoCHeiko Schocher
generate the boot.bin file for all atmel SoC (arm920, arm926, armv7) Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> [fix subject] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17ARM: atmel: spl: make css field configurableBo Shen
The clock source for master clock can be slow clock, main clock, plla clock or upll clock. So, make the clock source selection field in mckr can be configured. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17ARM: atmel: spl: make initialization more stableBo Shen
We need to make sure the main clock ready field in MCFR is set after switch to main crystal oscillator. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini
2014-11-14Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-11-13arm: mx6: add support for TBS2910 Matrix ARM miniPCSoeren Moch
Add initial support for TBS2910 Matrix ARM miniPC. Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC. Signed-off-by: Soeren Moch <smoch@web.de>
2014-11-13mx6: video_skip: Fix crash on NULL pointerNikolay Dimitrov
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg> Cc: Stefano Babic <sbabic@denx.de>
2014-11-13Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2014-11-13kconfig: imx6: add SUPPORT_SPLJohn Tobias
add SUPPORT_SPL feature for iMX6 SabreSD. It need to use mx6sabresd_spl_defconfig to compile it. Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
2014-11-13Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-11-13arm: mx6: Fix missing Kconfig option for NovenaMarek Vasut
Add two missing Kconfig options for Novena and drop the SPL from the Novena config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-13sun6i: ehci: Add sun6i ehci supportHans de Goede
Add support for the 2 ehci controllers found on the sun6i (A31) soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Marek Vasut <marex@denx.de>
2014-11-13sun6i: Poke magic sram controller register to avoid cache issuesHans de Goede
Without this the cache will only work in write-through mode, and as soon as it is put in write-back mode things break. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add dram initialization codeHans de Goede
Add full support for dram initialization, using a fixed clock and autodetection of the memory organization (numbers of channels, bus-width, etc.). This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK, extended with extra initialization sequences and the autodetect algorithm from boot0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun4i: Rename dram files to dram_sun4i.xHans de Goede
In preparation for adding sun6i dram support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add cpucfg register definitionsHans de Goede
Not used atm, for future use (e.g. PSCI). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add clock functions needed for SPL / DRAM initHans de Goede
Add clock_init_safe and clockset_pll5 functions, as these are needed for SPL support resp. DRAM init (which is needed for SPL too). Also add some extra clock register constant defines. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add new p2wi controller driverOliver Schinagl
The A31 uses a new push-pull two wire interface, which features higher transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8 bytes each time, this driver will only see very little use and thus is limited to single byte transmission only. Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini
2014-11-13kconfig: arm: move "armv8" define to arch/arm/KconfigMasahiro Yamada
Commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs) collected the default values of CONFIG_SYS_CPU into arch/arm/Kconfig. This commit moves "armv8" to there for consistency. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Georges Savoundararadj <savoundg@gmail.com>
2014-11-13kconfig: arm: select CPU_V7 for some new boardsMasahiro Yamada
This commit adds "select CPU_V7" for some new boards that were not covered by commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs). Redundant "SYS_CPU" defines and "string" directives should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Georges Savoundararadj <savoundg@gmail.com>
2014-11-13ARM: remove unused CPU directoryMasahiro Yamada
There is no board with CPU "arm_intcm". Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-11-12arm: imx: make bmode command work with SPL/U-Boot comboNikita Kiryanov
The bmode command forces the SoC to use a specific boot device by writing its boot mode into SRC_GPR9, and notifying the SoC of the change using SRC_GPR10[28] bit: if the bit is on, bootROM uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine the boot device. SPL on the other hand is oblivious to this distinction, so once the bootROM loads SPL from the device configured in SRC_GPR10, SPL will attempt to load U-Boot from the device configured in SRC_SMBR1, which is not updated by the bootROM to the value in SRC_GPR9. The result is that the selected boot device is not used across all the boot stages. Update spl_boot_device() to look at gpr9 when necessary. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Heiko Schocher <hs@denx.de>
2014-11-12ARM: cache-cp15: Use more accurate typesThierry Reding
size_t is the canonical type to represent variables that contain a size. Use it instead of signed integer. Physical addresses can be larger than 32-bit, so use a more appropriate type for them as well. phys_addr_t is a type that is 32-bit on systems that use 32-bit addresses and 64-bit if the system is 64-bit or uses a form of physical address extension to use a larger address space on 32-bit systems. Using these types the same API can be implemented on a wider range of systems. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-12ARM: cache_v7: Various minor cleanupsThierry Reding
Remove two gratuituous blank lines, uses u32 (instead of int) as the type for values that will be written to a register, moves the beginning of the variable declaration section to a separate line (rather than the one with the opening brace) and keeps the function signature on a single line where possible. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2014-11-11Revert "lib: bootm: add missing include"Michal Simek
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. This reverts commit 1e96220a5687efae2aed45ce56e143336c40d0a7. Remove duplicated vxworks.h header. The same change was done by "ARM: prevent compiler warnings from bootm.c" (sha1: 8d196e52b58d1e50a80c2f5067b201cda521c75c) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-12ARM: UniPhier: call pin_init() also in the normal bootMasahiro Yamada
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and it is defined in ./.config but not in spl/.config, so pin_init() should be called from the normal image so that UART works correctly. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: consolidate board_postclk_init() functionMasahiro Yamada
This commit merges arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c to arch/arm/cpu/armv7/uniphier/board_postclk_init.c Because PH1-Pro4 does not have the BCU block, add __weak to bcu_init(). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: add set_pinsel macro for use in assembly codeMasahiro Yamada
The function sg_set_pinsel is useful for switching I/O pins but it can be only used in C code. This commit adds a simple macro that is available in asm code. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12usb: UniPhier: add UniPhier on-chip EHCI host driver supportMasahiro Yamada
Support EHCI host driver used on Panasonic UniPhier platform. Since Device Tree is not supported on UniPhier yet, the base address of USB cores are passed from board files (platdevice.c). TODO for me: Move the base address to device trees. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de>
2014-11-12ARM: UniPhier: add MIO register fileMasahiro Yamada
This commit adds register defines of MIO (Media I/O) block of UniPhier platform. This file is necessary to control the reset signals of the USB cores. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: add EHCI host pin settings for PH1-Pro4Masahiro Yamada
These IO pins are necessary for port power control and over current detect. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: move DDR related configuration to KconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: reset on-board devices on start-upMasahiro Yamada
If a support card is attached to the main board, the on-board SMSC9118 LAN controller is available. It must be kept in reset state for a while on start-up. When the board is kicked via a debbuger rather than pushing the hardware reset button, on-board chips are not reset; in this case the reset signals should be asserted by software. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-11kconfig: zynq: Add ZYBO boardPeter Crosthwaite
Add a defconfig and Kconfigury for the Digilent ZYBO board. Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-11arm: dts: zynq: Add digilent ZYBO board dtsPeter Crosthwaite
It's a Zynq board similar in design to the currently supported ones. 512MB of RAM and UART1 is used. Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
generated by cgit (git 2.34.1) at 2024-12-29 14:28:03 +0000