| Age | Commit message (Collapse) | Author |
|---|
|
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add Reset Driver for ast2500 SoC. This driver uses Watchdog Timer to
perform resets and thus depends on it. The actual Watchdog device used
needs to be configured in Device Tree using "aspeed,wdt" property, which
must be WDT phandle, for example:
rst: reset-controller {
compatible = "aspeed,ast2500-reset";
aspeed,wdt = <&wdt1>;
}
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Make functions for locking and unlocking SCU part of SCU API.
Many drivers need to modify settings in SCU and thus need to unlock it
first. This change makes it possible.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver supports ast2500 and ast2400 SoCs.
Only ast2500 supports reset_mask and thus the option of resettting
individual peripherals using WDT.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Pull in the Device Tree for ast2500 from the mainline Linux kernel.
The file is copied from
https://raw.githubusercontent.com/torvalds/linux/34ea5c9d/arch/arm/boot/dts/aspeed-g5.dtsi
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch is required for correct SPL device tree creation by fdtgrep
as fdtgrep looks for u-boot,dm-pre-reloc property of the node to include
it in the spl device tree.
Not adding it in these subnodes ignores the pin muxing of peripherals
which is almost always in the subnodes.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
am33xx does not support OneNAND, but we need this define anyway
to let UBI SPL code compile.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
This patch adds gpio driver supporting driver model for stm32f7 gpio.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Christophe KERELLO <christophe.kerello@st.com>
[trini: Add depends on STM32]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Also added DT binding doc for stm32 fmc(flexible memory controller).
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
In dram_init_banksize there seems to be a typo concerning
a plausibility check of the fdt.
Testing sc > 2 twice does not make any sense.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
With 3f66149d9fb4 we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9fb4 ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_DEKBLOB
Note: This option does not seem to actually be enabled by any board.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply under SECURE_BOOT for mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_CRAMFS
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_CLK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Before converting this to Kconfig, rename it to match the other PMICs.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Xilinx fixes for v2017.05
- Fix usbotg on Miami board
- Cleanup zc1751 defconfig
|
|
On ARM v7M, the processor will return to ARM mode when executing
a blx instruction with bit 0 of the address == 0. Always set it
to 1 to stay in thumb mode.
Tested on STM32f746-disco board
Similar commit:
f99993c10882f7dc8ec35993d5febe59aac01e6a
Author: Matt Porter <mporter@konsulko.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.
Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
There are more and more cases where if we do not use gcc-6.0 or later we
run into problems where our binaries are too large for the targets.
Given the prevalence of gcc-6.0 or later toolchains at this point in
time, we give notice now that starting with v2018.01 we will require
gcc-6 (or later) for ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630. Correct the naing and offsets per the documentation
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19
The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
|
|
|
|
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
