summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2016-07-26omap4: i2c: correct register offset for sync registerMugunthan V N
The register offset of i2c_sysc offset is not correct as per omap4 TRM [1], correct the offsets as per the documentation. [1] - http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25rockchip: sdram: Fix register layout for LinuxJohn Keeping
The ChromeOS kernel reads the RAM settings from PMU_SYS_REG2 and expects the bootloader to store the necessary information there. We're using the same register to pass the same information between the SPL and U-Boot but in a slightly different format. Change this to use the format expected by the Linux DMC driver so that the system doesn't hang in Linux by misconfiguring the RAM. This is almost the same as commit b5788dc ("rockchip: rk3288: correct sdram setting") which was reverted in commit b525556 ("Revert "rockchip: rk3288: correct sdram setting"") but parenthese have been added to apply the mask correctly when reading the "bw" setting and a couple of minor style issues have been fixed to keep check_patch.pl happy. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25ARM64: rockchip: add support for rk3399 SoC based evbKever Yang
RK3399 is a SoC from Rockchip with dual-core Cortex-A72 and quad-core Cortex-A53 CPU. It supports two USB3.0 type-C ports and two USB2.0 EHCI ports. Other interfaces are very much like RK3288, the DRAM are 32bit width address and support address from 0 to 4GB-128MB range. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25dts: add support for Rockchip rk3399 socKever Yang
These files are from kernel upstream: "649a371 Add linux-next specific files for 20160616" with some modification need by U-Boot: - chosen with stdout-path to uart2. - add clock-frequency for uart2 Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25rockchip: Use rockchip_get_clk() to obtain the SoC clockSimon Glass
The current code picks the first available clock. In U-Boot proper this is the oscillator device, not the SoC clock device. As a result the HDMI display does not work. Fix this by calling rockchip_get_clk() instead. Fixes: 135aa950 (clk: convert API to match reset/mailbox style) Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
2016-07-25rockchip: Add a way to obtain the main clock deviceSimon Glass
On Rockchip SoCs we typically have a main clock device that uses the Soc clock driver. There is also a fixed clock for the oscillator. Add a function to obtain the core clock. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-25cosmetic: rockchip: rk3288: rename rkclk_configure_cpuHeiko Stübner
The function is very specific to the rk3288 in its arguments referencing the rk3288 cru and grf and every other rockchip soc has differing cru and grf registers. So make that function naming explicit. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25cosmetic: rockchip: sort socs according to numbersHeiko Stübner
Having some sort of ordering proofed helpful in a lot of other places already. So for a larger number of rockchip socs it might be helpful as well instead of an ever increasing unsorted list. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25rockchip: rk3288: add fastboot supportXu Ziyuan
Enable fastboot feature on rk3288. This path doesn't support the fastboot flash function command entirely. We will hit "cannot find partition" assertion without specified partition environment. Define gpt partition layout in specified board such as firefly-rk3288, then enjoy it! Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25rockchip: Exclude rk_timer for ARM64Andreas Färber
It conflicts with the generic_timer. Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25rockchip: Clean up CPU selectionAndreas Färber
In preparation for RK3368 and RK3399, which need to select ARM64, don't select CPU_V7 at the ARCH_ROCKCHIP level but at the SoC level instead. Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25board: move all the rockchip board in one folderKever Yang
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them to 'rockchip' which is a real _vendor_ name, and meet the architecure 'board/<vendor>/<board-name>/'. More boards from rockchip like evb_rk3288, evb_rk3399 will comes later. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
2016-07-25rockchip: add basic support for evb-rk3288 boardXu Ziyuan
evb-3288 board RK3288-based development board with 2 USB ports, HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to display pins, I2C, SPI, UART and GPIOs. This add some basic files required to allow the board to output serial messaged and can run command(mmc info etc). evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC. Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-25rockchip: add option to change method of loading u-bootXu Ziyuan
If we would like to boot from SD card, we have to implement mmc driver in SPL stage, and get a slightly large SPL binary. Rockchip SoC's bootrom code has the ability to load spl and u-boot, then boot. If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to bootrom in board_init_f(), then bootrom loads u-boot binary. Loading sequence after rework: bootrom ==> spl ==> bootrom ==> u-boot Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip: Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-25Merge git://git.denx.de/u-boot-nand-flashTom Rini
2016-07-25ARM: am33xx: Always inhibit init/refresh during DDR phy initRuss Dill
A couple of commits have modified the am33xx/am437x ddr2/ddr3 initialization path to fix certain issues, but have had the side effect of causing L3 noc errors during initialization. The two commits are: 69b918 "am33xx,ddr3: fix ddr3 sdram configuration" fc46ba "arm: am437x: Enable hardware leveling for EMIF" The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all platforms. This delays initialization and refresh until a later stage. The 500us timer can be programmed for platforms that require it and for platforms that don't require it. It is currently hardcoded for 400MHz systems. For systems with a higher memory frequency this needs to be a larger value, and for systems with a lower memory frequency this can be a lower value. This can be considered a separate issue and corrected in a later commit. Signed-off-by: Russ Dill <Russ.Dill@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25ARM: am33xx: Fix DDR init delay placementRuss Dill
The delay needs to be before the write to ref_ctrl register which initiates refreshes. An improper initialization sequence generates an L3 noc error. Signed-off-by: Russ Dill <Russ.Dill@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25keystone: k2h/e/l: Fix DMA coherency for QM PDSPKaricheri, Muralidharan
commit 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid. This, in effect disabled DMA coherency for QM PDSP. Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs, the #ifdef should been removed in the first place. Do the same. Fixes: 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery") Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-24sunxi: Enable NAND controller on the CHIPBoris Brezillon
Enable the NAND controller in the sun5i-r8-chip.dts. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-07-24sun5i: Add NAND controller to the sun5i DTSIMaxime Ripard
Add the NAND controller definition to sun5i.dtsi. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-07-24sunxi: Add missing macros to configure the NAND controller clkBoris Brezillon
We need some macros to manipulate the NAND controller clock. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-07-24ARM: uniphier: add clock/reset settings for xHCI of ProXstream2Masahiro Yamada
Deassert resets and enable clock signals of xHCI blocks if the corresponding CONFIG is enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24ARM: uniphier: add PH1-LD21 board dataMasahiro Yamada
This has the same silicon die as PH1-LD20, but includes DRAM chips in its package. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24ARM: uniphier: introduce flags to uniphier_board_data structureMasahiro Yamada
I need to add more board attributes, so the "flags" member will be handier than separate boolean ones. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24ARM: uniphier: rename outer-cache register macrosMasahiro Yamada
Sync register macros with Linux code. This will be helpful to develop the counterpart of Linux. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24ARM: uniphier: clear notification flag before L2 operationMasahiro Yamada
Clear the flag immediately before cache operation to not depend on the previous state. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24ARM: uniphier: use (devm_)ioremap() instead of map_sysmem()Masahiro Yamada
This does not have much impact on behavior, but makes code look more more like Linux. The use of devm_ioremap() often helps to delete .remove callbacks entirely. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-23ARM: uniphier: select CONFIG_ARMV8_SPIN_TABLEMasahiro Yamada
This is needed when booting Linux without ARM Trusted Firmware. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-23ARM: dts: uniphier: renumber serial aliases for Gentil/Vodka boardsMasahiro Yamada
On these two boards, the serial0 is used for inter-chip connection, so cannot be used for login console. The serial2 is used instead for them, but it is tedious to use because upper level deployment projects must switch login console per board. [ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-07-22arm: omap5: fix build dependency for secure devicesAndreas Dannenberg
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that causes the build to break when that option is not active. Fix this issue by only building the u-boot_HS.img target when building U-Boot into an actual FIT image. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22arm: am4x: fix build dependency for secure devicesAndreas Dannenberg
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT when building U-Boot for AM43xx high-security (HS) devices that causes the build to break when that option is not active. Fix this issue by only building the u-boot_HS.img target when building U-Boot into an actual FIT image. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22armv8: spl: Call board_init_r from crt0_64 in SPLJeremy Hunt
As part of the startup process for boards using the SPL, the meaning of board_init_f changed such that it should return normally rather than calling board_init_r directly. (see db910353a126d84fe8dff7a694ea792f50fcfb6a ) This was fixed in 32-bit arm, but broke when SPL was added to 64 bit arm. This fixes crt0_64 so that it calls board_init_r during the SPL and removes the direct call from board_init_f from the arm SPL example. Signed-off-by: Jeremy Hunt <Jeremy.Hunt@DEShawResearch.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-22armv7: simplify identify_nand_chipLadislav Michl
Use newly introduced function Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22armv7: armv7: introduce set_gpmc_cs0Ladislav Michl
Allow boards to runtime detect flash type. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22armv7: make gpmc_cfg constLadislav Michl
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> [trini: Adapt am33xx, duovero, omap_zoom1] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-22armv7: add reset timeout to identify_nand_chipLadislav Michl
identify_nand_chip hangs forever in loop when NAND is not present. As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout to let function fail gracefully allowing caller to know NAND is not present. On NAND equipped board, reset succeeds on first read, so 1000 loops seems to be safe timeout. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22spl: zImage support in Falcon modeLadislav Michl
Other payload than uImage is currently considered to be raw U-Boot image. Check also for zImage in Falcon mode. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-22Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-07-22ARM64: zynqmp: Remove get_uart_clk()Michal Simek
ZynqMP will use reading clock freq directly from DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22ARM64: zynqmp: Enable CLK and SPL_CLK by defaultMichal Simek
Serial driver starts to use clk framework that's why enable it by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22spl: Fix compilation warnings for arm64Michal Simek
Make code 64bit aware. Warnings: +../arch/arm/lib/spl.c: In function ‘jump_to_image_linux’: +../arch/arm/lib/spl.c:63:3: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] +../common/spl/spl_fat.c: In function ‘spl_load_image_fat’: +../common/spl/spl_fat.c:91:33: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-21Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-07-21Revert "stm32: Change USART port to USART6 for stm32f746 discovery board"Tom Rini
Per Vikas' request, the problem this commit is supposed to be solving is something he doesn't see and further this introduces additional hardware requirements. This reverts commit 4b2fd720a7b2f78c42d1565edf4c67f378c65440. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-21ARM: tegra: pick up actual memory sizeStephen Warren
On Tegra186, U-Boot is booted by the binary firmware as if it were a Linux kernel. Consequently, a DTB is passed to U-Boot. Cache the address of that DTB, and parse the /memory/reg property to determine the actual RAM regions that U-Boot and subsequent EL2/EL1 SW may actually use. Given the binary FW passes a DTB to U-Boot, I anticipate the suggestion that U-Boot use that DTB as its control DTB. I don't believe that would work well, so I do not plan to put any effort into this. By default the FW-supplied DTB is the L4T kernel's DTB, which uses non-upstreamed DT bindings. U-Boot aims to use only upstreamed DT bindings, or as close as it can get. Replacing this DTB with a DTB using upstream bindings is physically quite easy; simply replace the content of one of the GPT partitions on the eMMC. However, the binary FW at least partially relies on the existence/content of some nodes in the DTB, and that requires the DTB to be written according to downstream bindings. Equally, if U-Boot continues to use appended DTBs built from its own source tree, as it does for all other Tegra platforms, development and deployment is much easier. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21ARM: Add save_boot_params for ARMv8Stephen Warren
Implement a hook to allow boards to save boot-time CPU state for later use. When U-Boot is chain-loaded by another bootloader, CPU registers may contain useful information such as system configuration information. This feature mirrors the equivalent ARMv7 feature. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21ARM: tegra: add IVC protocol implementationStephen Warren
IVC (Inter-VM Communication) protocol is a Tegra-specific IPC (Inter Processor Communication) framework. Within the context of U-Boot, it is typically used for communication between the main CPU and various auxiliary processors. In particular, it will be used to communicate with the BPMP (Boot and Power Management Processor) on Tegra186 in order to manipulate clocks and reset signals. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21ARM: tegra: unify Tegra186 Makefile a bitStephen Warren
Many files in arch/arm/mach-tegra are compiled conditionally based on Kconfig variables, or applicable to all platforms. We can let the main Tegra Makefile handle compiling (or not) those files to avoid each SoC- specific Makefile needing to duplicate entries for those files. This leaves the SoC-specific Makefiles to compile truly SoC-specific code. In the future, we'll hopefully add Kconfig variables for all the other files, and refactor those files, and so reduce the need for SoC-specific Makefiles and/or ifdefs in the Makefiles. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21ARM: tegra: split p2771-0000 buildStephen Warren
There are multiple versions of p2771-0000 board. There are SW visible incompatible differences between the versions, and they are relevant to U-Boot. Create separate "A02" and "B00" defconfigs (named after the first and/or only board rev the defconfig supports) so that users can select which build they want. With the minimal set of HW currently enabled in U-Boot, the differences are irrelevant, hence the DT files aren't different. However, that will change in a future patch. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21ARM: tegra: fix Tegra186 DT GPIO binding headerStephen Warren
Tegra186 uses different GPIO port IDs compared to previous chips. Make sure the SoC DT file includes the correct GPIO binding header. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21Revert "imx_common: Return MMCSD_MODE_FS in spl_boot_mode() also for EXTFS"Breno Lima
Commit c1ebf54868359005 ("imx_common: Return MMCSD_MODE_FS in spl_boot_mode() also for EXTFS") causes SPL breakage on wandboard: ERROR: v7_dcache_inval_range - start address is not aligned - 0x1820006c ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1820086c ERROR: v7_dcache_inval_range - start address is not aligned - 0x1820006c ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1820086c ** First descriptor is NOT a primary desc on 0:1 ** spl: no partition table found SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### This error is seen when SPL and u-boot.img are stored in the raw SD card partition. This reverts commit c1ebf54868359005c32944c1473668d5fcaca158. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-23 18:23:19 +0000