summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2018-10-02rockchip: rk3188: explicitly set vcc_sd0 pin to gpio on rk3188-radxarockHeiko Stuebner
It is good practice to make the setting of gpio-pinctrls explicitly in the devicetree, and in this case even necessary. Rockchip boards start with iomux settings set to gpio for most pins and while the linux pinctrl driver also implicitly sets the gpio function if a pin is requested as gpio that is not necessarily true for other drivers. The issue in question stems from uboot, where the sdmmc_pwr pin is set to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage loader. The regulator controlled by the pin is active-low though, so when the dwmmc hw-block sets its enabled bit, it actually disables the regulator. By changing the pin back to gpio we fix that behaviour. [picked from the identical linux patch https://patchwork.kernel.org/patch/10609253/] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02rockchip: rk3188: add u-boot-specific mmc propertiesHeiko Stuebner
The dwmmc controllers on rk3188 do not have idma support, so need to use the fifo-mode and it my tests they became confused and stopped working if the frequency was to high. While I only tested in somewhat bigger steps, 32MHz for example hung the controller, while reducing it to 16MHz worked just fine and is reasonably fast to load a kernel from mmc. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-09-30dts: db410c: Add bindings for MSM USB phyRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30db410c: serial# env using msm board serialRamon Fried
The serial# environment variable needs to be defined so it will be used by fastboot as serial for the endpoint descriptor. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30dts: db410c: add alias for USBRamon Fried
Alias is required so req-seq will be filled. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-29Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2018-09-29Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A, LS1043A, LS1046A, LS1088A, LS2088A. Switch to driver model for SATA on LS1021A and LS1043A. Add support for LS1012AFRWY rev C board. Enable SMMU for LS1043A.
2018-09-29ARM: da850evm_direct_nor_defconfig: Enable DM_SERIALAdam Ford
With DM enabled, this patch enables DM_SERIAL and removes the NS16550 initialization from da850_lowlevel since the driver will take care of that itself. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29ARM: DTS: various omap3: Remove cd-inverted from u-boot.dtsiAdam Ford
With the omap_mmc driver no longer supporting cd-inverted, this patch removes all these references since they are not needed. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29mmc: omap_mmc: Remove invert referencesAdam Ford
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards using the 'cd-invert' option will no longer need to do this. This patch removes the support for 'invert' from the MMC driver. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Fix warning over when !DM_GPIO] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-28ARM: dts: at91: sama5d4_xplained: add onewire connector for LCD eepromEugen Hristev
Add onewire node in device tree for TM series LCDs Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28ARM: dts: at91: sama5d2_ptc: add onewire connector for LCD eepromEugen Hristev
Add onewire node in device tree for TM series LCDs Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28ARM: dts: at91: sama5d27_som1_ek: add onewire connector for LCD eepromEugen Hristev
Add onewire node in device tree for TM series LCDs Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28ARM: dts: at91: sama5d3_xplained: add onewire connector for LCD eepromEugen Hristev
Add onewire node in device tree for TM series LCDs Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28ARM: dts: at91: sama5d2_xplained: add onewire connector for LCD eepromEugen Hristev
Add onewire node in device tree for TM series LCDs Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d2_ptc_ek: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d3_xplained: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28ARM: dts: sun8i: Update A23/A33/r16 dts(i) files from Linux-v4.18-rc3Jagan Teki
Update all A23/A33/r16 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commits. A23: commit bc3bd041fe766219a44688b182c260064007f0cc Author: Miquel Raynal <miquel.raynal@bootlin.com> Date: Tue Apr 24 17:55:02 2018 +0200 ARM: dts: sun8i: a23/a33: declare NAND pins A33: commit 88fe315d2c0a397ef42d7639addab0e021ae911d Author: Maxime Ripard <maxime.ripard@bootlin.com> Date: Wed Apr 4 11:57:15 2018 +0200 ARM: dts: sun8i: a33: Add the DSI-related nodes r16: commit 9621d0bd1b0d61167e1853ac68cf4869c31bcc96 Author: Miquel Raynal <miquel.raynal@bootlin.com> Date: Tue Apr 24 17:55:03 2018 +0200 ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support Note: - Drop pinctrl from sun8i-r16-nintendo-nes-classic-edition.dts since sun8i-a23-a33.dtsi is added with Linux sync. - Don't sync non U-Boot supported dts files sun8i-a23-ippo-q8h-v1.2.dts sun8i-a23-ippo-q8h-v5.dts sun8i-a33-et-q8-v1.6.dts sun8i-a33-ippo-q8h-v1.2.dts sun8i-r16-nintendo-nes-classic.dts sun8i-r16-nintendo-super-nes-classic.dts Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28ARM: dts: sun7i: Update A20 dts(i) files from Linux-v4.18-rc3Jagan Teki
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commit: commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5 Author: Stefan Mavrodiev <stefan@olimex.com> Date: Wed May 16 14:38:08 2018 +0300 ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board Note: - Update sun7i-a20-primo73.dts as per Linux, since this dts is U-Boot specific. - Drop sun7i-a20-olimex-som-evb-emmc.dts since no board added for this. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28ARM: dts: sun6i: Update A31/A31s dts(i) files from Linux-v4.18-rc3Jagan Teki
Update all A31/A31s devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commit: commit b240b419db5d624ce7a5a397d6f62a1a686009ec Merge: 9c2dd8405c0c 518d2f43c358 Author: Linus Torvalds <torvalds@linux-foundation.org> Date: Thu Apr 5 21:18:09 2018 -0700 Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28ARM: dts: sun5i: Update A10s/A13/gr8/r8 dts(i) files from Linux-v4.18-rc3Jagan Teki
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commit: commit 190e3138f9577885691540dca59c2f07540bde04 Merge: cafc87023b0d a7affb13b271 Author: Arnd Bergmann <arnd@arndb.de> Date: Tue Mar 27 14:58:00 2018 +0200 Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3Jagan Teki
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commit: commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532 Author: Pascal Roeleven <dev@pascalroeleven.nl> Date: Fri Apr 20 12:21:12 2018 +0200 ARM: dts: sun4i: Fix incorrect clocks for displays Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts like other dts file since there dts file are U-Boot specific. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-27armv7: ls102xa: Disable QE before enter deep sleepRan Wang
Otherwise system will hang after executing wfi. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add icid setup supportLaurentiu Tudor
Reuse the existing ICID setup code done for LS1046A smmu enablement and add the equivalent setup for LS1043A chips. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: advertise QMan v3 in configurationLaurentiu Tudor
The QMan IP block in this SoC is version 3.2 so advertise this in the SoC configuration header. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: fsl-layerscape: add missing qe base address defineLaurentiu Tudor
Add define for QUICC Engine register block base address. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> [York S: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv7: dts: fsl-ls1021a: add sata node support enable sata for ls1021a-qds ↵Peng Ma
and ls1021a-twr Add sata node to support this feature. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv7: fsl: remove sata supportPeng Ma
Remove the old implementation in order to enable DM for sata Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: dts: fsl-ls1043a: add sata node supportPeng Ma
Add sata node to support ls1043a. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv7: ls1021a: enable esdhcYinbo Zhu
This patch is to enable eSDHC for ls1021a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1046a: add eSDHC nodeYinbo Zhu
This patch is to add eSDHC node for ls1046a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add eSDHC nodeYinbo Zhu
This patch is to add eSDHC node for ls1043a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1088a: add eSDHC nodeYinbo Zhu
This patch is to add eSDHC node for ls1088a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls2088a: add eSDHC nodeYinbo Zhu
This patch is to add eSDHC node for ls2088a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8/ls1088a/ls2088a: esdhc: Add esdhc clock supportYinbo Zhu
This patch adds esdhc clock support for ls1088a and ls2088a. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27ppa/fm/qe: use block layer in ppa/fm/qe driverYinbo Zhu
At present the MMC subsystem maintains its own list of MMC devices. This cannot work with driver model when CONFIG_BLK is enabled, use blk_dread to replace previous mmc read interface, use mmc_get_blk_desc to get the mmc device property. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> [York S: reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.11 - Handle BOARD_LATE_INIT via Kconfig SPL: - Enable GZIP for all partitions types(not only for kernel) ZynqMP: - Rearrange pmufw version handling - Support newer PMUFW with improved fpga load sequence Zynq: - Cleanup config file - Simplify zybo config by enabling option via Kconfig net: - Fix gems max-speed property reading - Enable support for fixed-link phys
2018-09-26Merge tag 'signed-efi-next' of git://github.com/agraf/u-bootTom Rini
Patch queue for efi - 2018-09-26 A lot of goodness in this release. We're *very* close to running the UEFI Shell and SCT natively. The only missing piece are HII protocols. - FAT write support (needed for SCT) - improved FAT directory support (needed for SCT) - RTC support with QEMU -M virt - Sandbox support (run UEFI binaries in Linux - yay) - Proper UTF-16 support - EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell) - EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell) - Fix window size determination - Fix Tegra by explicitly unmapping RAM - Clean up handle entanglement - Lots of generic code cleanup [trini: Fixup merge conflict in include/configs/qemu-arm.h] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-26fpga: zynqmp: Modify PL bitstream loading sequenceSiva Durga Prasad Paladugu
This patch modifies PL bitstream loading sequence as per latest Xilfpga which supports all variants of bitstream images generated from vivado and from bootgen. With this new change in Xilfpga, uboot doesn't need to validate and swap bitstream as it will be taken care inside Xilfpga. ZynqMP PL driver now checks for supporting PMUFW version before skipping the validation and swap sequence as there can be old PMUFW which doesn't supports this feature. In this case, driver uses old way of PL bitstream loading sequence. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-26arm64: zynqmp: Return pmufw version for zynqmp_pmufw_version()Siva Durga Prasad Paladugu
Modify the zynqmp_pmufw_version() routine to return PMUFW version so that it can be reused wherever required. Get PMUFW version from PMU only once at bootup and later just return stored value. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-26arm64: zynqmp: Move PM version related macros to .hSiva Durga Prasad Paladugu
This patch moves the PM version related macros to .h file so that they can be reused in other files. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-26arm64: zynqmp: Handle CONFIG_BOARD_LATE_INIT via KconfigMichal Simek
Disable BOARD_LATE_INIT via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-25ARM: use asm-generic/atomic.hChris Packham
Make use of asm-generic/atomic.h retaining the smp_mb_... definitions. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-25mmc: omap_hsmmc: Fix pbias for omap3_logic to enable CD pinAdam Ford
The MMC card detect pin is connected to gpio127 on omap3_logic. When setting up the pbias register for MMC, let's also enable gpio_127 for the card detect. As part of the package deal, gpio_126 and gpio_129 are also enabled. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-25arm: spear: fix enabling of SSP2 clockQuentin Schulz
The SSP2 clock is at bit 6 in the register, so the value is 0x40 unlike the current 0x70 which enables the clock of UART2, SSP1 and SSP2. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Acked-by: Stefan Roese <sr@denx.de>
2018-09-25arm: spear: enable SSP1, 2 and 3 clocks when SPI controller driver is builtQuentin Schulz
SPI controllers SSP1, 2 and 3 require to enable their respective clocks. Let's enable them only when the SPI controller driver is built. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
2018-09-25ARM: dts: stm32mp1: Add EHCI support for stm32mp157c-ev1 boardPatrice Chotard
Add DT nodes to enable EHCI support Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-25ARM: dts: stm32mp1: Add usb gadget support for stm32mp157c-ev1 boardPatrice Chotard
Add DT nodes to enable DWC2 gadget support Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-23arm: qemu-arm: enable RTC (PL031) by defaultAKASHI Takahiro
Virtual machine provided by qemu-arm has a ARM PL031 Real Time Clock device. With this patch, the driver is enabled by default. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
generated by cgit (git 2.34.1) at 2025-01-08 04:08:30 +0000