summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2019-02-01sound: rockchip: Add sound support for jerrySimon Glass
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral. Enable sound support and add the required device-tree pieces. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: rk3288: Add i2s pinctrl and clock supportSimon Glass
Add support for setting pinctrl and clock for I2S on rk3288. This allows the sound driver to operate. These settings were created by rkmux.py Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01ARM: DTS: am43xx: Enable the DTS entries for USB port #2 in SPLJean-Jacques Hiblot
This is required to enable the USB port #2 in SPL when DM_USB is used. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-02-01ARM: DTS: am43xx: Add aliases for the USB portsJean-Jacques Hiblot
Although not required, it doesn't hurt to explicitly map the USB ports to a USB controller. Without this, the port number will be derived from the binding order of the peripheral devices. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-02-01ARM: DTS: Resync am3517-evm.dts with Linux 5.0-rc3Adam Ford
The chosen node was added in the kernel. This may come in handy in the future, so resync with 5.0-rc3 Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01ARM: dts: da850-evm: Re-sync with Kernel 5.0Adam Ford
Resync with Kernel 5.0-rc3 Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4Tien Fong Chee
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FATTien Fong Chee
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01ARM: DTS: am335x-evm: Use USB0 in peripheral modeJean-Jacques Hiblot
This USB port is mainly used for RNDIS and DFU. To be able to use it with DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01ARM: dts: am335x-shc: add u-boot specific dtsiHeiko Schocher
add u-boot specific am335x-shc-u-boot.dtsi file, in which we add u-boot specific adaptions. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01arm: dts: add am335x-shc.dts for shc boardHeiko Schocher
add DTS from linux tree commit "47bfa6d9dc8c060bf56554a465c9031e286d2f80" change for U-Boot: switch to SPDX-license identifier. Signed-off-by: Heiko Schocher <hs@denx.de>
2019-01-31Merge tag 'video-updates-for-2019.04-rc1' of git://git.denx.de/u-boot-videoTom Rini
- ihs and imx driver fixes - relax EDID validation checks for 0 hsync/vsync pulse width (support some quirky displays)
2019-01-31arm: meson: board-gx: Setup VPU in fdtMaxime Jourdan
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer. Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for EFI, and sets up simple-framebuffer nodes if simplefb support is enabled. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31arm64: dts: meson-gx: add hhi reg entry to hdmi_txMaxime Jourdan
There's no reliable way to reuse the hhi entry from the vpu as is done in the linux kernel, so we duplicate it here. We will be able to sync against kernel DTS in the future when the VPU gets based on the clock framework rather than the HHI reg. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-01-31arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supplyNeil Armstrong
The hdmi_5v regulator must be enabled to provide power to the physical HDMI PHY and enables the HDMI 5V presence loopback for the monitor. Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> [backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
2019-01-31arm64: dts: meson-gx: vpu should be probed before relocationMaxime Jourdan
Flag the appropriate nodes with u-boot,dm-pre-reloc Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-01-31video: Add Meson Video Processing Unit DriverNeil Armstrong
This adds video output support for Amlogic GXBB/GXL/GXM chips. The supported ports are CVBS and HDMI (based on DW_HDMI). When using HDMI, only DMT modes are supported. There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB) Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> [narmstrong: fixed defines alignment in meson_canvas.c] Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-30Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- Enable DM_MMC support
2019-01-30arm: sunxi: Enable DM_MMCJagan Teki
Enable DM_MMC for all Allwinner SoCs, this will eventually enable BLK. Also removed DM_MMC enablement in few parts of sunxi configurations. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2019-01-30sunxi: A64: pinebook-u-boot: Include sunxi-u-boot.dtsiJagan Teki
Like other Allwinner A64 boards, pinebook also need altering auto-numbering of mmc2 to mmc1 which is available in common sunxi dsti file, sunxi-u-boot.dtsi Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which takes more precedence for u-boot.dtsi inclusion and it eventually failed to include the sunxi-u-boot.dtsi. So, this patch add support to include the sunxi-u-boot.dtsi in the sun50i-a64-pinebook-u-boot.dtsi Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
2019-01-30arm: dts: sunxi: Alter mmc2 auto-numbering to mmc1Jagan Teki
Environment and fastboot mmc devices are configured based on the number of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA. If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device. But with DM_MMC the mmc devices are numbered as per the dts node enablement. If there is a chance of having enabling all mmc nodes in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices will failed to assign proper emmc device since mmc2 is emmc in most of the Allwinner platforms. So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since aliases take precedence over auto-numbering. If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2 the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1 and mmc2 become mmc1 Without aliases of mmc1 = &mmc2; ------------------------------- MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2 With aliases of mmc1 = &mmc2; ---------------------------- MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... OK Some platforms like A20 has mmc0...mmc3, but there is no usecases now for enabling all mmc controllers in any of A20 board dts files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-30Merge tag 'u-boot-imx-20190129' of git://git.denx.de/u-boot-imxTom Rini
For 2019.04
2019-01-29arm: stm32mp1: deploy spl in root folderPatrick Delaunay
Update generation of spl binaries - continue to generate all SPL files in spl sub-directory - copy in root folder the needed file for user (YOCTO, buildroot): u-boot-spl.stm32 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-01-28imx: video: Fix return value issueYe Li
When framebuffer driver init is failed, we should return the err value not 0. So the video init can exit immediately. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-28ARM: DTS: imx6q-logicpd: Update DTS/DTSI filesAdam Ford
The i.MX6 SOM and development kits have undergone significant updates and changes over the past few months. This re-sync's the U-Boot with Logic PD's BSP. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-01-28arm: dts: imx7s-warp: Create alias for mmc0 to &usdhc3Bryan O'Donoghue
This patch sets up an alias for mmc0 to usdhc3. Before the DM conversion only usdhc3 was enabled and therefore it appeared as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2, which left unattended would drive changes to existing warp7 bootscripts and environment variables that rely on mmc 0. Setup the alias of mmc0 and usdhc3 so that existing warp7 boot code will work unmodified. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28arm: dts: imx7s-warp: Import Linux warp7 dtsBryan O'Donoghue
This patch imports the Linux kernel warp7 dts as at upstream kernel commit cf76c364a1e1. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28arm: dts: imx7: Correct spelling mistake in GPIO nameBryan O'Donoghue
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once corrected we can import the latest kernel DTS unmodified. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-01-28imx8: cpu: restrict checking ROM passover info for revAPeng Fan
Passover info only for revA. move get_cpu_rev out of CONFIG_CPU to avoid build failure when using get_cpu_rev in SPL. Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again in normal U-Boot stage. Also if still checking passover info in normal U-Boot stage, need to make the passover code executed after arch_cpu_init_dm. So to make it easy and clean, only execute the code for SPL stage. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: Check the PL310 version for applying errataYe Li
Apply errata based on PL310 version instead of compile time. Also set Prefetch offset to 15, since it improves memcpy performance by 35%. Don't enable Incr double Linefill enable since it adversely affects memcpy performance by about 32MB/s and reads by 90MB/s. Tested with 4K to 16MB sized src and dst aligned buffer. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Ye Li <ye.li@nxp.com>
2019-01-28ARM: imx: fix: Provide correct enum values for ONENAND/NOR boot recognitionLukasz Majewski
According to "Table 5-1. Boot Device Select" (page 335, i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017) the BOOT_CFG1[3] have following values (regarding EIM booting): 0 - NOR flash and 1 - ONENAND This commit provides correct identification of the boot medium for IMX6Q boards booting from NOR memory (MCCMON6 is one of them). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-28dm: arm: imx: migrate cx9020 to CONFIG_DM_MMCPatrick Bruenn
Enable esdhc1/2 device nodes for cx9020 and build with CONFIG_DM_MMC=y Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28arm: imx: Add esdhc1/2 nodes to imx53.dtsiPatrick Bruenn
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y They are copied from Linux 4.20 Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28imx: Fix potential lmb memory overwritten by stackYe Li
At default, u-boot reserves the memory from SP - 4KB to DRAM end for lmb in arch_lmb_reserve. So lmb won't allocate any memory from it. But we found the 4K gap for SP is not enough now, because some FDT updating operations are added in our u-boot before jumping to kernel, which needs larger stack. This causes the lmb allocated memory is overwritten by stack. Fix the issue by implementing the board_lmb_reserve to reserve from SP - 16KB to memory end for lmb. Signed-off-by: Ye Li <ye.li@nxp.com>
2019-01-28imx: build flash.bin for i.MX8Peng Fan
Build flash.bin for i.MX8 when SPL enabled. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: mkimage_fit_atf: introduce BL33_BASE_ADDRPeng Fan
Introduce BL33_BASE_ADDR, then we could reuse this script for i.MX8QXP. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28dts: imx8qxp-mek: introduce u-boot dtsiPeng Fan
Introduce u-boot dtsi for i.MX8QXP MEK board. we do not introduce a common dtsi for SoC, because different board has different requirement on which needs to be enabled in SPL DM. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28spl: imx8: add spl boot devicePeng Fan
Add spl_boot_device for i.MX8, also add BOOT_DEVICE_MMC2_2 for spl_boot_mode. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28arm: imx: build mach-imx for i.MX8Peng Fan
To enable SPL for i.MX8, we could reuse code in arch/arm/mach-imx. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8: scu: use dedicated MU for SPLPeng Fan
SPL runs in EL3 mode, except MU0_A, others are not powered on, and could not be used. However normal U-Boot use MU1_A, so we could not reuse the one in dts. And we could not replace the one in dts with MU0_A, because MU0_A is reserved in secure world. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8qxp: add SUPPORT_SPL optionPeng Fan
Enable SUPPORT_SPL option for i.MX8QXP, then we could enable SPL. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28arm: dts: imx7: colibri: add usdhci peripherals to device treeStefan Agner
Add usdhci peripherals to device tree. This allows to use DM_MMC for Colibri iMX7 devices. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2019-01-28arm: dts: imx7: colibri: split dt for raw NAND and eMMC devicesStefan Agner
In preparation of adding CONFIG_DM_MMC support use separate device trees for raw NAND and eMMC devices. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-01-28mx7: Do not call lcdif_power_down() in the SPL caseFabio Estevam
Like it was done on imx6 in commit 9236269de57d ("imx: mx6: Fix implementantion reset_misc") Do not call lcdif_power_down() in the SPL case to fix the following build error: LD spl/u-boot-spl MKIMAGE u-boot.img arch/arm/mach-imx/built-in.o: In function `reset_misc': /home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down' scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: Add PHYTEC phyBOARD-i.MX6UL-SeginMartyn Welch
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063). CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Board: PHYTEC phyCORE-i.MX6UL I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC0 Working: - Eth0 - i2C - MMC/SD - NAND - UART (1 & 5) - USB (host & otg) Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-01-28imx: hab: Convert non-NULL IVT DCD pointer warning to an errorBreno Matheus Lima
The following NXP application notes and manual recommend to ensure the IVT DCD pointer is Null prior to calling HAB API authenticate_image() function: - AN12263: HABv4 RVT Guidelines and Recommendations - AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using HABv4 - CST docs: High Assurance Boot Version 4 Application Programming Interface Reference Manual Commit ca89df7dd46f ("imx: hab: Convert DCD non-NULL error to warning") converted DCD non-NULL error to warning due to the lack of documentation at the time of first patch submission. We have warned U-Boot users since v2018.03, and it makes sense now to follow the NXP recommendation to ensure the IVT DCD pointer is Null. DCD commands should only be present in the initial boot image loaded by the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error if a DCD pointer is present in an image being authenticated by calling the HAB RVT API. Older versions of HAB will process and run DCD if it is present, and this could lead to an incorrect authentication boot flow. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-01-26linker: Modify linker scripts to be more genericTom Rini
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the same script for both SPL and TPL. Add logic to scripts/Makefile.spl to pass in the right value when preprocessing the script. Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jagan Teki <jagan@openedev.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-01-26rockchip: Add TPL_MAX_SIZE for RK3288Tom Rini
Per Kever Yang, 32768 is a reasonable max size for TPL on RK3288. Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-01-26ARM: mach-omap2: Kconfig: Allow OMAP5 devices to set entry pointAndrew F. Davis
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to have an non-standard boot address in memory. This may be due to the device being a high security variant, which place the Initial SoftWare (ISW) after certificates and secure software. Allow these devices to set this from Kconfig. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-01-26spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFUAndrew F. Davis
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT to allow for cleaner use in code. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-27 15:17:20 +0000