| Age | Commit message (Collapse) | Author |
|---|
|
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The bf527-ezkit boards are getting too big to fit into their reserved
flash space, so we need to use a lzma compressed logo.
Since the video driver code is very similar, add lzma compressed support
to all of the Blackfin video drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
We don't need these setup manually, so let the bss do the rest. On
Blackfin systems, we clear the bss before executing any C code that
would use these, so this should be fine.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This makes Blackfin behave the same as other ports, and fixes many gcc
warnings that show up with 4.5+:
board.c:40:1: warning: optimization may eliminate reads and/or
writes to register variables
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
1. Add linkage.h support from blackfin to common include,
which is a reduced version from Linux.
2. Add architecture part support of linkage.h into blackfin
3. Fix include path of in blackfin related to linkage.h
due to header file movement.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
These are rarely used, but the post code does currently, so add small
redirect hacks for that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Common U-Boot API wants this define, so import asm/cache.h from Linux
to provide suitable defines.
Acked-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
|
|
Make it easy for any Blackfin board to enable led/push button tests.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
When we aren't doing resource tracking, the gpio_free() function is a
stub that simply returns, so pull this logic up a level and make it an
inline stub in the header. Now we don't have to waste time at any of
the call sites.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Set the default post word location to an L1 data location for all
Blackfin parts so things "just work" for most people.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The Blackfin gpio command isn't terribly Blackfin-specific. So generalize
the few pieces into two new optional helpers:
name_to_gpio() - turn a string name into a GPIO #
gpio_status() - display current pin bindings (think /proc/gpio)
Once these pieces are pulled out, we can relocate the cmd_gpio.c into the
common directory.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We need the updated LDR bit defines for our LDR utils.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Common code already takes care of setting up these defines when a port
hasn't specified them, so punt the duplicate values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The recent global data changes (making the size autogenerated) broke the
board info handling on Blackfin ports as we were lying and lumping the
bd_t size in with the gd_t size. So use the new dedicated bd_t size to
setup its own address in memory.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The __BFIN_DEF_ADSP_BF537_proc__ define isn't setup anymore, so use
the one coming from the compiler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This is a revert of 821ad16fa9900c as Wolfgang doesn't like the new code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
Since some of the defines in our config.h use the generated defines, we
need to include the generated header. This fixes building of the Blackfin
start.S file (where the stack is setup).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The CONFIG_BFIN_CPU option is largely used in the build system, so move
it out of the board config.h and into the board config.mk. It'd be nice
to keep everything in the config.h, but the patch to extract that value
early was rejected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Only the BF561 port was using the common dual core headers, so merge them
into the BF561 specific headers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Only the BF533 port was using the common extended headers, so merge them
into the BF533 specific headers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
These are unused now, so punt them to clean things up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There is no BF541 processor variant, so punt headers for it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This moves the last piece from the old spi_flash driver to the new SPI
framework -- optional DMA RX support. This typically cuts speeds by ~40%
at the cost of additional ~300 bytes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Conflicts:
include/ppc4xx.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Linux uses an offset of 8 to switch from hardware cs to a gpio cs,
so have u-boot use the same value. Also make sure it is public
for boards to access.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Motivation:
* Old environment code used a pessimizing implementation:
- variable lookup used linear search => slow
- changed/added variables were added at the end, i. e. most
frequently used variables had the slowest access times => slow
- each setenv() would calculate the CRC32 checksum over the whole
environment block => slow
* "redundant" envrionment was locked down to two copies
* No easy way to implement features like "reset to factory defaults",
or to select one out of several pre-defined (previously saved) sets
of environment settings ("profiles")
* No easy way to import or export environment settings
======================================================================
API Changes:
- Variable names starting with '#' are no longer allowed
I didn't find any such variable names being used; it is highly
recommended to follow standard conventions and start variable names
with an alphanumeric character
- "printenv" will now print a backslash at the end of all but the last
lines of a multi-line variable value.
Multi-line variables have never been formally defined, allthough
there is no reason not to use them. Now we define rules how to deal
with them, allowing for import and export.
- Function forceenv() and the related code in saveenv() was removed.
At the moment this is causing build problems for the only user of
this code (schmoogie - which has no entry in MAINTAINERS); may be
fixed later by implementing the "env set -f" feature.
Inconsistencies:
- "printenv" will '\\'-escape the '\n' in multi-line variables, while
"printenv var" will not do that.
======================================================================
Advantages:
- "printenv" output much better readable (sorted)
- faster!
- extendable (additional variable properties can be added)
- new, powerful features like "factory reset" or easy switching
between several different environment settings ("profiles")
Disadvantages:
- Image size grows by typically 5...7 KiB (might shrink a bit again on
systems with redundant environment with a following patch series)
======================================================================
Implemented:
- env command with subcommands:
- env print [arg ...]
same as "printenv": print environment
- env set [-f] name [arg ...]
same as "setenv": set (and delete) environment variables
["-f" - force setting even for read-only variables - not
implemented yet.]
- end delete [-f] name
not implemented yet
["-f" - force delete even for read-only variables]
- env save
same as "saveenv": save environment
- env export [-t | -b | -c] addr [size]
export internal representation (hash table) in formats usable for
persistent storage or processing:
-t: export as text format; if size is given, data will be
padded with '\0' bytes; if not, one terminating '\0'
will be added (which is included in the "filesize"
setting so you can for exmple copy this to flash and
keep the termination).
-b: export as binary format (name=value pairs separated by
'\0', list end marked by double "\0\0")
-c: export as checksum protected environment format as
used for example by "saveenv" command
addr: memory address where environment gets stored
size: size of output buffer
With "-c" and size is NOT given, then the export command will
format the data as currently used for the persistent storage,
i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
prepend a valid CRC32 checksum and, in case of resundant
environment, a "current" redundancy flag. If size is given, this
value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
checksum and redundancy flag will be inserted.
With "-b" and "-t", always only the real data (including a
terminating '\0' byte) will be written; here the optional size
argument will be used to make sure not to overflow the user
provided buffer; the command will abort if the size is not
sufficient. Any remainign space will be '\0' padded.
On successful return, the variable "filesize" will be set.
Note that filesize includes the trailing/terminating '\0'
byte(s).
Usage szenario: create a text snapshot/backup of the current
settings:
=> env export -t 100000
=> era ${backup_addr} +${filesize}
=> cp.b 100000 ${backup_addr} ${filesize}
Re-import this snapshot, deleting all other settings:
=> env import -d -t ${backup_addr}
- env import [-d] [-t | -b | -c] addr [size]
import external format (text or binary) into hash table,
optionally deleting existing values:
-d: delete existing environment before importing;
otherwise overwrite / append to existion definitions
-t: assume text format; either "size" must be given or the
text data must be '\0' terminated
-b: assume binary format ('\0' separated, "\0\0" terminated)
-c: assume checksum protected environment format
addr: memory address to read from
size: length of input data; if missing, proper '\0'
termination is mandatory
- env default -f
reset default environment: drop all environment settings and load
default environment
- env ask name [message] [size]
same as "askenv": ask for environment variable
- env edit name
same as "editenv": edit environment variable
- env run
same as "run": run commands in an environment variable
======================================================================
TODO:
- drop default env as implemented now; provide a text file based
initialization instead (eventually using several text files to
incrementally build it from common blocks) and a tool to convert it
into a binary blob / object file.
- It would be nice if we could add wildcard support for environment
variables; this is needed for variable name auto-completion,
but it would also be nice to be able to say "printenv ip*" or
"printenv *addr*"
- Some boards don't link any more due to the grown code size:
DU405, canyonlands, sequoia, socrates.
=> cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Stefan Roese <sr@denx.de>,
Heiko Schocher <hs@denx.de>
- Dropping forceenv() causes build problems on schmoogie
=> cc: Sergey Kubushyn <ksi@koi8.net>
- Build tested on PPC and ARM only; runtime tested with NOR and NAND
flash only => needs testing!!
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Cc: Stefan Roese <sr@denx.de>,
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
|
|
So far, getenv() would work before relocation is most cases, even
though it was not intended to be used that way. When switching to a
hash table based implementation, this would break a number of boards.
For convenience, we make getenv() check if it's running before
relocation and, if so, use getenv_f() internally.
Note that this is limited to simple cases, as we use a small static
buffer (32 bytes) in the global data for this purpose.
For this reason, it is also not a good idea to convert all current
uses of getenv_f() into getenv() - some of the existing use cases need
to be able to deal with longer variable values, so getenv_f() is still
needed and recommended for use before relocation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The L1 regions of Core B are not directly accessible from Core A, so we
need to use DMA to get at them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The current pinmux handling has spread throughout Blackfin drivers and
board code and is getting hideous to maintain. So import the gpio and
portmux layer from the Blackfin Linux code. This should spur a serious
of cleanups across the Blackfin tree.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
