| Age | Commit message (Collapse) | Author |
|---|
|
In MIPS assembly there have historically been 2 variants of immediate
addition - the standard "addi" which traps if an overflow occurs, and
the unchecked "addiu" which does not trap on overflow. In release 6 of
the MIPS architecture the trapping variants of immediate addition &
subtraction have been removed. In preparation for supporting MIPSr6,
stop using the trapping instructions from assembly & switch to their
unchecked variants.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
Add support for the TPLink WDR4300 router, which is based on the
AR9344 MIPS 74Kc CPU and has 128 MiB of RAM. The USB is supported
on this system as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add support for the Atheros AR934x WiSoCs. This patchs adds complete
system init, including PLL and DRAM init, both of which happen from
full C environment, since the AR934x has proper SRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add code to ungate the ethernet controller on ar933x and ar934x .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add node for both ethernet controllers in the ar933x.
The PHY is attached only to the first ethernet controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add code to ungate the USB controller on ar933x and ar934x .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add generic EHCI node for the ChipIdea EHCI controller in the ath79.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
The assignment const T var; var = value; is illegal, since var is
constant. Drop the const to fix the compiler warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
The indent in this file triggers my OCD, so fix it. Replace multiple
spaces with tabs and align the values in one column.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
|
|
Add MIPS 74Kc tune Kconfig option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
[added missing tune-y entry in arch/mips/Makefile]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
There really is zero reason for including netdev.h in generic mips CPU code.
Removing the netdev.h from cpu.c also fixes the following compiler warning:
In file included from arch/mips/cpu/cpu.c:10:0:
include/netdev.h:204:41: warning: 'struct eth_device' declared inside parameter list [enabled by default]
int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int));
^
include/netdev.h:204:41: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
use 'const' keywork to qualify readonly attribute for lookup-table member
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
used a uniform BIT macro for register bit-field shift
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
This patch add board-level code and base DT for AP143.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch add board-level code and base DT for AP121.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch enable work for qca953x SOC.
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
This patch enable work for ar933x SOC.
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
This patch add some common code for QCA/Atheros ath79 SOCs such as
DDR tuning, chip reset and CPU detection.
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
Spelling corrections for (among other things):
* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
|
|
MIPS arch do not update 'reg' property of /memory node.
As a result Linux bootup will not work unless board.dts
file contains right /memory offset-size information or
board implements required memory fixup.
Fixing by renaming (unused) _arch_fixup_memory_node_ to
_arch_fixup_fdt_ in arch/mips/lib/bootm.c inline with ARM arch.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Enable MUSB host and USB storage support for Microchip
PIC32MZ[DA] Starter Kit.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
|
|
The "R" constraint supplies the address of an variable in a register. Use
"r" instead and adjust asm to supply the content of addr in a register
instead.
Fixes: 2b8bcc5a ("MIPS: avoid .set ISA for cache operations")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This adds ethernet, TFTP support for PIC32MZ[DA] Starter Kit. Also
custom environment variables/scripts are added to help boot from network.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
|
|
Enable MMC, SDHCI, FAT_FS support for PIC32MZ[DA] StarterKit.
Also add custom scripts, rules to boot Linux from microSD card.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
|
|
This adds support for Microchip PIC32MZ[DA] StarterKit board
based on a PIC32MZ[DA] family of microcontroller.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Add Microchip PIC32MZ[DA] SoC family support.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Create initial directory, Kconfigs needed for PIC32 architecture
support. Also add PIC32 specific register definition required for drivers.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The existing mips_io_port_base variable isn't suitable for use early
during boot since it will be stored in the .data section which may not
be writable pre-relocation. Fix this by moving the I/O port base address
into struct arch_global_data. In order to avoid adding this field for
all targets, make this dependant upon a new Kconfig entry
CONFIG_DYNAMIC_IO_PORT_BASE. Malta is the only board which sets a
non-zero I/O port base, so select this option only for Malta.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
CONF_SLOWDOWN_IO is never set for any target, so remove the dead code in
the SLOW_DOWN_IO macro. This is done in preparation for changes to
mips_io_port_base which can be avoided in this path by removing it
entirely.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
This patch makes sure that the flush/invalidate_dcache_range() functions
can handle corner-case calls like this -- invalidate_dcache_range(0, 0, 0);
This call is valid and is happily produced by USB EHCI code for example.
The expected behavior of the cache function(s) in this case is that they
will do no operation, since the size is zero.
The current implementation though has a problem where such invocation will
result in a hard CPU hang. This is because under such conditions, where the
start_addr = 0 and stop = 0, the addr = 0 and aend = 0xffffffe0 . The loop
will then try to iterate over the entire address space, which in itself is
wrong. But iterating over the entire address space might also hit some odd
address which will cause bus hang. The later happens on the Atheros MIPS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
|
|
Fix 32 vs 64 bit load/store instructions. Access CP0_WATCHHI as
32 Bit register. Use 64 Bit register access for clearing gd_data
and copying U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Argument boot_flags of board_init_f() should be set to 0 as
$a0 may be utilized in lowlevel_init() or mips_cache_reset()
or previous stage boot-loader.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
As part of the bug.h / BUILD_BUG_* clean up, this file was missed.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add support for functions clrbits_X(), setbits_X() and clrsetbits_X()
on MIPS.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Add a SPDX license identifier to MIPS header files where it is
still missing.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Update definitions for processor, registers as well as assemby
macros.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Mainly sync asm/io.h to get a working ioremap() implementation
as well as the full set of I/O accessors. Pull in additional
header files to make this work.
Furthermore port over the directory 'arch/mips/include/asm/mach-generic/'
with contains default definitions for I/O and memory spaces and default
implementations for mapping those spaces. All files in that directory
can be overwritten by a SoC/machine.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Add Kconfig symbol for L1 cache shift like the kernel does.
The value of CONFIG_SYS_CACHELINE_SIZE is not a reliable source
for ARCH_DMA_MINALIGN anymore, because it is optional on MIPS.
If CONFIG_SYS_CACHELINE_SIZE is not defined by a board, the
cache sizes are automatically detected and ARCH_DMA_MINALIGN
would be set to 128 Bytes.
The default value for CONFIG_MIPS_L1_CACHE_SHIFT is 5 which
corresponds to 32 Bytes. All current MIPS boards already used
that value. While on it, fix the Malta board to use a value of 6
like the kernel port does.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Move setup of -march to arch/mips/Makefile and follow the design on ARM.
Also add a possibility to chose specific CPU tune options.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Refactor machine setup like it is done on ARM. While on it,
also support "include <mach/file.h" for machine specific
header files.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Prepare sub-folder for device-tree files. Make support for
device-tree on MIPS available in Kbuild/Kconfig.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
|
|
SPL binaries are usually linked to a fixed address in SRAM.
Furthermore SPL binaries do not need to relocate itself. Thus
do not build them as position-independent binaries which helps
to largely reduce the size of SPL binaries.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Put all functions coded in assembly in sub-sections of
section .text. This allows the linker to garbage collect
unused assembly functions too.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Correctly annotate _start and relocate_code as functions to
produce more readable disassembly code generated by objdump.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
With CONFIG_CMD_GPIO compilation reports error.
common/cmd_gpio.c:13:22: fatal error: asm/gpio.h: No such file or directory
#include <asm/gpio.h>
^
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
