| Age | Commit message (Collapse) | Author |
|---|
|
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
|
|
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This is useful when we just want to wipe out the TLBs. There's currently
a function that resets the ddr tlbs to a different value; it is changed to
utilize this function. The new function can be used in conjunction with
setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address
range as needed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The Fman device tree node binding allows for the entire Fman firmware binary
data to be embedded in the device tree. This eliminates the need to have
NOR flash mapped to Linux just so that the Fman driver can see the firmware.
The location of the Fman firmware is taken from the 'fman_ucode' environment
variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The ePAPR specification says that phandle properties should be called
"phandle", and not "linux,phandle". To facilitate the migration from
"linux,phandle" to "phandle", we update fdt_qportal() to use the new
function, fdt_create_phandle(). This function abstracts the creation of
phandle properties.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Had a typo such that P1017E would not be detected correctly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a
bank soft-reset after the bank was configured and enabled, even though
enabling a bank causes it to reset. Because the reset was required for
multiple errata, it was not properly enclosed in an #ifdef, and so was
not removed with all the other rev1 errata work-arounds.
Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if
bank 2 is enabled, but this was not being done for SERDES protocols 0xF
and 0x10. The bank reset also happened to enable bank 3 (apparently an
undocumented feature). Simply removing the reset breaks these two
protocols.
It turns out that every time we call enable_bank(), we do want at least
one lane of the bank enabled, either because the bank is supposed to be
enabled, or because we need the clock from that bank enabled.
For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we
call enable_bank(), because that array is used elsewhere to determine if
the bank is available.
Note that the side effect of these changes is that the work-arounds for
these two errata are now linked. Specifically, if SERDES-A001 is
enabled, then we need SERDES-8 enabled as well.
Because this was the only SERDES bank soft-reset, there is no need to
implement a work-around for erratum SERDES-A003.
Also fix an off-by-one error in a printf().
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ed Swarthout <swarthou@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Modify support for USB mode fixup:
- Add common support for USB mode and phy type
device tree fix-up for all USB controllers
mentioned in hwconfig string
- Fetch USB mode and phy type via hwconfig; if not
defined in hwconfig, then fetch them from env
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has
data width and primary sdram width. The latter one has different meaning
for DDR3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In case of empty SPD or checksum error, fallback to raw timing on
supported boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We used to have fixed parameters for soldered DDR chips. This patch
introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing
data from DDR chip datasheet, implemneted in board-specific files or header
files.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Only use DDR DIMM part number if SPD has valid length, to prevent from
display garbage in case SPD doesn't cover these fields.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
If the bus width is 32-bit, burst chop should be disabled and burst length
should be 8. Read from SPD or other source to determine the width.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The P2041 is similar to P2040, however has a 10G port and backside L2
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add P2040 SoC specific information:
* LIODN setup
* Portal configuration
* etc
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add ifdef protection in LBC code to handle the case in which
CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On a 8308 based board it was found that the PEX_GLK_RATIO register
(programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This
was tracked to the fact that the pci express clock frequency was not being
assigned to the pciexp1_clk entry in the global data structure in file
arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in
'do_clocks' command.
Signed-off-by: Bill Cook <cook@isgchips.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
CPO value and driver strength settings are board specifc.
Also allow SPD data fetch from any accessible I2C EEPROM.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Running on mpc837x without CONFIG_FSL_ESDHC leads to
i2c1_clk not being set at all. It is bound to clock
of encryption module. fix this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Reword "The DIMM max tCKmin is ..." to "The DDR clock is faster than the slowest
DIMM(s) can support". Fixed interger type in printf as well.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The compatible property for the L2 cache node (on 85xx systems that don't
have a CPC) was using a value for the property length that did not match
the actual length of the property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts. All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.
Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly. The
work-around is to enable and then disable bank two after bank three is
enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The
current code does this only for XAUI, so extend it to the other protocols.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two
and three to be disabled (powered down) in the RCW. Display a warning
message if this is not the case.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.
* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix fdt bportal to pass the bman revision number to kernel via device tree.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
To make sure that machine change operation work successfully, change
timing parameters first before changing machine for chip select on IFC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
This reverts commit 39768f7715ed637ef02f49fc7de664cc1aaf14b3.
Reson: it breaks a number of boards with embedded environment as the
code size grows in some places.
|
|
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
-msingle-pic-base is a new gcc option for ppc and
it reduces the size of my u-boot with 6-8 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
-msingle-pic-base will be in gcc 4.6, however
backported patches are available at
http://bugs.gentoo.org/show_bug.cgi?id=347281
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
The -fPIC flag belongs with -mrelocatable, move it there.
Also change -fPIC to -fpic as this produces smaller
binaries.
However, currently -mrelocatable promotes -fpic to -fPIC, a
fix for this is in upcoming gcc 4.6 or you can apply this small
patch to gcc:
diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h
index 8da8410..e4b8280 100644
--- a/gcc/config/rs6000/sysv4.h
+++ b/gcc/config/rs6000/sysv4.h
@@ -227,7 +227,8 @@ do { \
} \
\
else if (TARGET_RELOCATABLE) \
- flag_pic = 2; \
+ if (!flag_pic) \
+ flag_pic = 2; \
} while (0)
#ifndef RS6000_BI_ARCH
--
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
Removed clearing of L2 cache as SRAM as it is not necessary without ECC.
This also speeds up the booting process.
Signed-off-by: Fabian Cenedese <cenedese@indel.ch>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Remove the SERDES8 erratum work-around code that only applied to P4080
rev1, which is not supported by this version of U-Boot.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM
and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more
appropriate CONFIG_SYS prefix as well as be consistent with 83xx.
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
