summaryrefslogtreecommitdiff
path: root/arch/powerpc/cpu
AgeCommit message (Collapse)Author
2011-08-04video: Add SHARP LQ084S3LG01 LCD support on P1022DSTimur Tabi
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board. This device only supports 800x600 resolution, so if that resolution is selected, assume that this is the device. The device is attached to the LVDS port on the P1022DS board. The existing 800x600 entry (for the PDM360NG board) is actually 800x480, so we fix that. To support two different 800x resolutions, the Y-resolution is now passed to fsl_diu_init() and both values are used to pick the proper fb_videomode structure. The data for the 800x600 video mode is originally from Jiang Yutang. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com>
2011-07-29powerpc/8xxx: Remove dependency on <usb.h>Kumar Gala
We used <usb.h> for USB_MAX_DEVICE. However this requires we actual build in support for USB into u-boot (which should not be required for device tree fixup). At this time no FSL SoC that utilizies this code (83xx/85xx) has more than 2 USB controllers. So we replace USB_MAX_DEVICE with a local define FSL_MAX_NUM_USB_CTRLS. If/when a device shows up with more than 2 controllers we can easily bump this value or refactor into a proper define per SoC. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: enable USB2 gadget mode for corenet ds boardShaohui Xie
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to 'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break out if it cannot find 'usb1', so drop the 'else' clause to make driver scan all the 'usbx'. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: verify the device tree before booting LinuxTimur Tabi
Introduce ft_verify_fdt(), a function that is called after the device tree has been fixed up, that displays warning messages if there is a mismatch between the physical addresses of some devices that U-Boot has configured with what the device tree says the addresses are. This is a particular problem when booting a 36-bit device tree from a 32-bit U-Boot (or vice versa), because the physical address of CCSR is wrong in the device tree. When the operating system boots, no messages are displayed, so the user generally has no idea what's wrong. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29MPC8xxx: drop redundant boot messagesWolfgang Denk
Current code would print RAM size information like this: DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off) Turn a number of printf()s into debug() to get rid of the redundant "DDR: " string like this: DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off) Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500Kumar Gala
At some point we broke the detection of e500v1 class cores. Fix that and simply the code to just utilize PVR_VER() to have a single case statement. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: Fix up clock_freq property in CAN node of dtsBhaskar Upadhaya
Fix up the device tree property associated with the Flexcan clock frequency. This property is used to calculate the bit timing parameters for Flexcan. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: provide 85xx flush_icache for cmd_cacheMatthew McClintock
This provides a function that will override the weak function flush_icache to let 85xx boards to flush the icache cc: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com>
2011-07-29powerpc/85xx: Handle the lack of L2 cache on P2040/P2040EKumar Gala
The P2040/P2040E have no L2 cache. So we utilize the SVR to determine if we are one of these devices and skip the L2 init code in cpu_init.c and release. For the device tree we skip the updating of the L2 cache properties but we still update the chain of caches so the CPC/L3 node can be properly updated. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: Add support for P2041[e] XAUI in SERDESKumar Gala
We add XAUI_FM1 into the SERDES tables for P2041[e] devices. However for the P2040[e] devices that dont support XAUI we handle this at runtime via SVR checks. If we are on a P2040[e] device the SERDES functions will behave as follows: is_serdes_prtcl_valid() will always report invalid if prtcl passed in is XAUI_FM1. serdes_get_prtcl() will report NONE if the prtcl in the table is set to XAUI_FM1. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: Rename P2040 id & SERDES to P2041Kumar Gala
P2041 is the superset part that covers both P2040 & P2041. The only difference between the two devices is that P2041 supports 10g/XAUI and has an L2 cache. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29powerpc/85xx: Adding configuration for DCSRCR to enable 32M accessStephen George
Configuring DCSRCR to define the DCSR space to be 1G instead of the default 4M. DCSRCR only allows selection of either 4M or 1G. Most DCSR registers are within 4M but the Nexus trace buffer is located at offset 16M within the DCSR. Configuring the LAW to be 32M to allow access to the Nexus trace buffer. No TLB modification is required since accessing the Nexus trace buffer from within u-boot is not required. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-28unify version_stringAndreas Bießmann
This patch removes the architecture specific implementation of version_string where possible. Some architectures use a special place and therefore we provide U_BOOT_VERSION_STRING definition and a common weak symbol version_string. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Peter Pan <pppeterpppan@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-07-26serial: drop useless ctlr fieldMike Frysinger
The multi serial support has a "ctlr" field which almost no one uses, but everyone is forced to set to useless strings. So punt it. Funny enough, the only code that actually reads this field (the mpc8xx driver) has a typo where it meant to look for the SCC driver. Fix it while converting the check to use the name field. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Heiko Schocher <hs@denx.de> CC: Anatolij Gustschin <agust@denx.de> CC: Tom Rix <Tom.Rix@windriver.com> CC: Minkyu Kang <mk7.kang@samsung.com> CC: Craig Nauman <cnauman@diagraph.com> CC: Marek Vasut <marek.vasut@gmail.com> CC: Prafulla Wadaskar <prafulla@marvell.com> CC: Mahavir Jain <mjain@marvell.com>
2011-07-26serial: push default_serial_console to driversMike Frysinger
Rather than sticking arch/board/driver specific logic in the common serial code, push it all out to the respective drivers. The serial drivers declare these funcs weak so that boards can still override things with their own definition. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Heiko Schocher <hs@denx.de> CC: Anatolij Gustschin <agust@denx.de> CC: Tom Rix <Tom.Rix@windriver.com> CC: Minkyu Kang <mk7.kang@samsung.com> CC: Craig Nauman <cnauman@diagraph.com> CC: Prafulla Wadaskar <prafulla@marvell.com> CC: Mahavir Jain <mjain@marvell.com> Tested-by: Minkyu Kang <mk7.kang@samsung.com>
2011-07-22powerpc/mpc85xx: Add clear_ddr_tlbs functionBecky Bruce
This is useful when we just want to wipe out the TLBs. There's currently a function that resets the ddr tlbs to a different value; it is changed to utilize this function. The new function can be used in conjunction with setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address range as needed. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-22fman: insert the Fman firmware into the device treeTimur Tabi
The Fman device tree node binding allows for the entire Fman firmware binary data to be embedded in the device tree. This eliminates the need to have NOR flash mapped to Linux just so that the Fman driver can see the firmware. The location of the Fman firmware is taken from the 'fman_ucode' environment variable. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-22powerpc/85xx: add support the ePAPR "phandle" propertyTimur Tabi
The ePAPR specification says that phandle properties should be called "phandle", and not "linux,phandle". To facilitate the migration from "linux,phandle" to "phandle", we update fdt_qportal() to use the new function, fdt_create_phandle(). This function abstracts the creation of phandle properties. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-17powerpc/85xx: Fix detection of P1017EKumar Gala
Had a typo such that P1017E would not be detected correctly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/85xx: remove SERDES4 soft-reset work-aroundTimur Tabi
Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a bank soft-reset after the bank was configured and enabled, even though enabling a bank causes it to reset. Because the reset was required for multiple errata, it was not properly enclosed in an #ifdef, and so was not removed with all the other rev1 errata work-arounds. Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if bank 2 is enabled, but this was not being done for SERDES protocols 0xF and 0x10. The bank reset also happened to enable bank 3 (apparently an undocumented feature). Simply removing the reset breaks these two protocols. It turns out that every time we call enable_bank(), we do want at least one lane of the bank enabled, either because the bank is supposed to be enabled, or because we need the clock from that bank enabled. For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we call enable_bank(), because that array is used elsewhere to determine if the bank is available. Note that the side effect of these changes is that the work-arounds for these two errata are now linked. Specifically, if SERDES-A001 is enabled, then we need SERDES-8 enabled as well. Because this was the only SERDES bank soft-reset, there is no need to implement a work-around for erratum SERDES-A003. Also fix an off-by-one error in a printf(). Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Ed Swarthout <swarthou@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: Allow override DDR read-to-write turnaround timeYork Sun
Add this option to allow boards to override the default read-to-write turnaround time for better performance. Signed-off-by: York Sun <yorksun@freescale.com>
2011-07-11powerpc/8xxx: Update USB mode device tree fixupRamneek Mehresh
Modify support for USB mode fixup: - Add common support for USB mode and phy type device tree fix-up for all USB controllers mentioned in hwconfig string - Fetch USB mode and phy type via hwconfig; if not defined in hwconfig, then fetch them from env Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: fix DDR data width checkingYork Sun
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has data width and primary sdram width. The latter one has different meaning for DDR3. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: Adding fallback to raw timing on supported boardsYork Sun
In case of empty SPD or checksum error, fallback to raw timing on supported boards. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: Enable calculation for fixed DDR chipsYork Sun
We used to have fixed parameters for soldered DDR chips. This patch introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing data from DDR chip datasheet, implemneted in board-specific files or header files. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: Add 16-bit support for DDR3York Sun
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit DDR devices. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: check SPD length before using part numberYork Sun
Only use DDR DIMM part number if SPD has valid length, to prevent from display garbage in case SPD doesn't cover these fields. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/mpc8xxx: adjust DDR burst length and chop accroding to sdram widthYork Sun
If the bus width is 32-bit, burst chop should be disabled and burst length should be 8. Read from SPD or other source to determine the width. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/85xx: Add P2041 processor supportKumar Gala
The P2041 is similar to P2040, however has a 10G port and backside L2 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/p2040: Add various p2040 specific informationMingkai Hu
Add P2040 SoC specific information: * LIODN setup * Portal configuration * etc Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/85xx: Fix compile errors if CONFIG_SYS_DPAA_QBMAN isn't setKumar Gala
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also rearrange setting of _tbl_sz variables to utilize existing ifdef protection for things like FMAN. Also add protection around setup_portals() call in corenet_ds board code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/85xx: Fix compile errors if CONFIG_SYS_{BR,OR}0_PRELIM aren't setKumar Gala
Add ifdef protection in LBC code to handle the case in which CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a build. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-06MPC83XX: Fix PCI express clock setupBill Cook
On a 8308 based board it was found that the PEX_GLK_RATIO register (programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This was tracked to the fact that the pci express clock frequency was not being assigned to the pciexp1_clk entry in the global data structure in file arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in 'do_clocks' command. Signed-off-by: Bill Cook <cook@isgchips.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-07-06MPC83xx: add config options for memory setup.Andre Schwarz
CPO value and driver strength settings are board specifc. Also allow SPD data fetch from any accessible I2C EEPROM. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-07-06MPC837x: set i2c1_clkAndre Schwarz
Running on mpc837x without CONFIG_FSL_ESDHC leads to i2c1_clk not being set at all. It is bound to clock of encryption module. fix this. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-05-19Minor coding style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-13powerpc/mpc8xxx: reword max tCKmin messageYork Sun
Reword "The DIMM max tCKmin is ..." to "The DDR clock is faster than the slowest DIMM(s) can support". Fixed interger type in printf as well. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-13powerpc/85xx: fix compatible property for the L2 cache nodeTimur Tabi
The compatible property for the L2 cache node (on 85xx systems that don't have a CPC) was using a value for the property length that did not match the actual length of the property. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-12PPC405EX CHIP_21 erratumSteven A. Falco
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated 4/27/11) states that rev D processors may wake up with the wrong feature set. This patch implements the APM-proposed workaround. To enable this patch for your board, add the appropriate define for your CPU to your board header file. See kilauea.h for more information. The following variants are supported: #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY Please note that if you select the wrong define, your board will not boot, and JTAG will be required to recover. Tested on custom boards using: CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com> CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de> Signed-off-by: Steve Falco <sfalco@harris.com> Acked-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-05-10Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2011-04-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2011-04-30mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher
- serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-29fsl-ddr: Fix mixed-case macro namesKyle Moffett
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Change timebase divisor to be defined per processorKumar Gala
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because different SoCs have different divisor amounts. All the PQ3 parts are /8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001Timur Tabi
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1 are swapped. Erratum SERDES-A001 says that if bank two is kept disabled and after bank three is enabled, then the PLL for bank three won't lock properly. The work-around is to enable and then disable bank two after bank three is enabled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Extend SERDES9 erratum work-around to SGMII, SRIO, and AURORATimur Tabi
Part of the SERDES9 erratum work-around is to set some bits in the SerDes TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The current code does this only for XAUI, so extend it to the other protocols. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Display SERDES 8 erratum warning if banks are not disabledTimur Tabi
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two and three to be disabled (powered down) in the RCW. Display a warning message if this is not the case. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005Timur Tabi
SerDes PLL bandwidth default setting is incorrect when no lanes are configured as PCI Express. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc: use 'video-mode' environment variable to configure DIUTimur Tabi
Use the 'video-mode' environment variable (for Freescale chips that have a DIU display controller) to designate the full video configuration. Previously, the DIU driver used the 'monitor' variable, and it was used only to determine the output video port. The old definition of the "monitor" environment variable only determines which video port to use for output. This variable was set to a number (0, 1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The resolution was hard-coded into board-specific code. The Linux command-line arguments needed to be hard-coded to the proper video definition string. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-04-27powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020Roy Zang
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we need to enable for them to function. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2024-12-25 16:48:39 +0000