summaryrefslogtreecommitdiff
path: root/arch/powerpc/cpu
AgeCommit message (Collapse)Author
2010-09-23ppc4xx: Disable trace broadcast for 44x non debug modeVictor Gallardo
By default the trace broadcast is enabled on 44x systems. To reduce power consumption when instruction tracing is not needed, disable trace broadcast. Check External Debug Mode (EDM) bit to detect if it should be disabled or not. Resetting system via a debugger will set the DBCR0[EDM] bit. Resetting via u-boot or OS will not. Signed-off-by: Victor Gallardo <vgallardo@apm.com> Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Cleanup of PVR detection code in cpu.cStefan Roese
This patch cleans the PVR detection code in check_cpu() up a bit. Basically the strings are better seperated, resulting in an easier to understand and maintain code version. The #ifdef's couldn't be removed easily because of two reasons: - Some SoC revisions have the same PVR, so need a way to differentiate between those two SoC's. - In some case statements registers only available in this SoC variant are referenced. Instead I moved the CONFIG_440 #ifdef a bit, so that 405 platforms don't add this 440 detection code and vice versa. Resulting in this U-Boot image size change: 405EX (Kilauea): 408 bytes less 440EPx (Sequoia): 604 bytes less 460EX (Canyonlands): 564 bytes less Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2010-09-23ppc4xx: Use common NS16550 driver for PPC4xx UARTStefan Roese
This patch removes the PPC4xx UART driver. Instead the common NS16550 driver is used, since all PPC4xx SoC's use this peripheral device. The file 4xx_uart.c now only implements the UART clock calculation function which also sets the SoC internal UART divisors. All PPC4xx board config headers are changed to use this common NS16550 driver now. Tested on these boards: acadia, canyonlands, katmai, kilauea, sequoia, zeus Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Big header cleanup part 2, mostly PPC405 relatedStefan Roese
This cleanup is done by creating header files for all SoC versions and moving the SoC specific defines into these special headers. This way the common header ppc405.h and ppc440.h can be cleaned up finally. As a part from this cleanup, the GPIO definitions for PPC405EP are corrected. The high and low parts of the registers (for example CONFIG_SYS_GPIO0_OSRL vs. CONFIG_SYS_GPIO0_OSRH) have been defined in the wrong order. This patch now fixes this issue by switching these xxxH and xxxL values. This brings the GPIO 405EP port in sync with all other PPC4xx ports. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Big header cleanup, mostly PPC440 relatedStefan Roese
This patch starts a bit PPC4xx header cleanup. First patch mostly touches PPC440 files. A later patch will touch the PPC405 files as well. This cleanup is done by creating header files for all SoC versions and moving the SoC specific defines into these special headers. This way the common header ppc405.h and ppc440.h can be cleaned up finally. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Move gpio.h to ppc4xx-gpio.h since its ppc4xx specificStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Move ppc4xx headers to powerpc include directoryStefan Roese
This patch moves some ppc4xx related headers from the common include directory (include/) to the powerpc specific one (arch/powerpc/include/asm/). This way to common include directory is not so cluttered with files. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-21fsl: refactor MPC8610 and MPC5121 DIU code to use existing bitmap and logo ↵Timur Tabi
features The Freescale MPC8610 and MPC5121 DIU code had re-implement two features that already existed in U-Boot: bitmap drawing and top-of-screen logo (CONFIG_VIDEO_LOGO). So delete the 8610-specific code and use the built-in features instead. Signed-off-by: Timur Tabi <timur@freescale.com>
2010-09-08bedbug_860.c, bedbug_603e.c: Fix return type to silence compile warnings.Wolfgang Denk
commit 47e26b1b "cmd_usage(): simplify return code handling" caused the following compile warnings: bedbug_860.c: In function 'bedbug860_do_break': bedbug_860.c:73: warning: 'return' with a value, in function returning void bedbug_860.c:121: warning: 'return' with a value, in function returning void Fix the return type. Actually these files could need some cleanup - commands should return proper error codes, and there are coding style issues. => To be fixed later. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-07Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2010-09-03ppc4xx: Invalidate d-cache when used as init-ramStefan Roese
We need to invalidate the data cache after it has been used as init-ram. This problem was detected on the lwmon5 update. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-03ppc4xx: Fix 440EPx bug in reconfigure_pll()Stefan Roese
This patch fixes a bug in reconfigure_pll(), where the detection of the current bootstrap option is wrong. The ICS bits where incorrectly shifted. This bug was found on the lwmon5 board, which uses bootstrap option H (I2C bootstrap EEPROM). Additionally a bit of code was moved into the if statement, since its only used after later on. No need to run this code all the time. Also, a few empty lines are added to make the code better readable. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Rupjyoti Sarmah <rsarmah@amcc.com> Cc: Victor Gallardo <vgallardo@appliedmicro.com>
2010-08-31Fix parameters to support RDIMM for P2020DSYork Sun
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19mpx85xx/fdt: Add cpu-release-addr for all coresMatthew McClintock
We currently do not add a cpu-release-addr for core 0, this is needed when we want to reset core 0 and later restart it from Linux Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19powerpc/85xx: Rename Security Engine Job Queue to Job Ring to match docsKumar Gala
Official docs call it the Job Ring not Job Queue for the p4080 security block. Match the docs to reduce confusion. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19powerpc/8xxx: share PIC defines among 85xx and 86xxKim Phillips
fixes breakeage introduced by commit a37c36f4e70bada297f281b0e542539ad43e50f6 "powerpc/8xxx: query feature reporting register for num cores on unknown cpus" Reported-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-09miiphy: constify device nameMike Frysinger
The driver name does not need to be writable, so constify it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09net ppc: fix ethernet device names with spacesHeiko Schocher
since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names with spaces drop a Warning: eth device name has a space! message. This patch fix it for: - "FEC ETHERNET" devices found on mpc512x, mpc5xxx, mpc8xx and mpc8220 boards. renamed to "FEC". - "SCC ETHERNET" devices found on mpc8xx, mpc82xx based boards. Renamed to "SCC". - "HDLC ETHERNET" devices found on mpc8xx boards Renamed to "HDLC" - "FCC ETHERNET" devices found on mpc8260 and mpc85xx based boards. Renamed to "FCC" Tested on the kup4k board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-04Rename getenv_r() into getenv_f()Wolfgang Denk
While running from flash, i. e. before relocation, we have only a limited C runtime environment without writable data segment. In this phase, some configurations (for example with environment in EEPROM) must not use the normal getenv(), but a special function. This function had been called getenv_r(), with the idea that the "_r" suffix would mean the same as in the _r_eentrant versions of some of the C library functions (for example getdate vs. getdate_r, getgrent vs. getgrent_r, etc.). Unfortunately this was a misleading name, as in U-Boot the "_r" generally means "running from RAM", i. e. _after_ relocation. To avoid confusion, rename into getenv_f() [as "running from flash"] Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2010-08-01powerpc/8xxx: query feature reporting register for num cores on unknown cpusKim Phillips
doing so helps avant garde users, such as those using simulators that allow users to configure the number of cores, so as to not have to manually adjust u-boot sources. h/w should also be reliably setting FRR NCPU in the future. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/8xxx: Improvement to DDR parametersyork
Changes for P2020DS DDR applies to other 8xxx platform Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/8xxx: Enable DDR3 RDIMM supportyork
Enabled registered DIMMs using data from SPD. RDIMMs have registers which need to be configured before using. The register configuration words are stored in SPD byte 60~116 (JEDEC standard No.21-C). Software should read those RCWs and put into DDR controller before initialization. Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/8xxx: Enabled address hashing for 85xxyork
For 85xx silicon which supports address hashing, it can be activated by hwconfig. Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/8xxx: Enable quad-rank DIMMs.york
Previous code presumes each DIMM has up to two rank (chip select). Newer DDR controller supports up to four chip select on one DIMM. Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/8xxx: Fix bug in memctrl interleaving & bank interleaving on cs0~cs4york
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual rank with 512MB each rank. Also check dimm size and rank size for memory controller interleaving Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/8xxx: Enabled hwconfig for memory interleavingKumar Gala
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with hwconfig parameters. The syntax is setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>" The mode values for memory controller interleaving are cacheline page bank superbank The mode values for bank interleaving are cs0_cs1 cs2_cs3 cs0_cs1_and_cs2_cs3 cs0_cs1_cs2_cs3 Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26powerpc/p4080: Add workaround for erratum CPU22Kumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/p4080: Add workaround for errata SERDES8Kumar Gala
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/p4080: Add support for initializing SERDESKumar Gala
Add support for initializing the SERDES blocks on CoreNet style QoriQ devices and the p4080 specific SERDES tables to know which actual componetns are enabled. Additionally, split out the Frame Manger (FMAN) into its specific ethernet ports instead of gross level of the full FMAN. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/85xx: Add support to initialize LIODN registers and portalsKumar Gala
On the new QorIQ/CoreNet based platforms we need to initialize the "portals" as access into the Data Path subystem as well as Logical IO Device Numbers (LIODN) that are used for the IOMMU (PAMU). Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/p4080: Add support for CPC(Corenet platform cache) on CoreNet platformsKumar Gala
The CoreNet style platforms can have a L3 cache that fronts the memory controllers. Enable that cache as well as add information into the device tree about it. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26powerpc/85xx: Move INIT_RAM_ADDR physical address to 36-bit spaceyork
If 36-bit physical address is used, move the INIT_RAM_ADDR to higher address. This frees the low 4GB address space for better use. Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-24cmd_usage(): simplify return code handlingWolfgang Denk
Lots of code use this construct: cmd_usage(cmdtp); return 1; Change cmd_usage() let it return 1 - then we can replace all these ocurrances by return cmd_usage(cmdtp); This fixes a few places with incorrect return code handling, too. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-07-24Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2010-07-23ppc4xx: Add ECC status info to machine-check exception for IBM DDR2 coreStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23ppc4xx: Add "ecctest" command to test/simulate ECC errorsStefan Roese
This patch adds the "ecctest" command to test and simulate ECC errors (single bit and/or double bit) while running from SDRAM. Currently only the IBM DDR2 controller is supported (405EX, 440SP(e), 460EX/GT). This is done by copying and calling functions, modifying the SDRAM controller operation mode, in internal SRAM/OCM. For correctable ECC errors (single bit) only the status will be printed since the DDR2 controller doesn't provide the faulting address: => ecctest 1000000 1 Using address 01000000 for 1 bit ECC error injection ECC: Correctable error Uncorrectable ECC errors (double bit) will also display the faulting address: => ecctest 1000000 2 Using address 01000000 for 2 bit ECC error injection ECC: Uncorrectable error at 0x0001000000 To enable this "ecctest" function you need to define CONFIG_CMD_ECCTEST in the board config header. Tested on katmai and t3corp. Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23ppc4xx: DDR/ECC: Use correct macros to clear error statusStefan Roese
Use the correct macro instead of the hardcoded 0x4c to clear the ECC status in the 440/460 DDR(2) error status register after ECC initialization. Also the non-440 parts (405EX(r) right now) and the IBM DDR PPC variants (440GX) use a different registers to clear this error status. Use the correct ones. Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23ppc4xx: Add CONFIG_DDR_RFDC_FIXED to allow board specific RFDC valuesStefan Roese
Using this define, a board can define an opimized RFDC value and use the auto calibration code to "tune" the remaining DDR2 controller calibration register. Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-21powerpc/85xx: Rework P1022 SERDES is_serdes_configured supportKumar Gala
Move serdes init until after we are in ram so we can keep track of a global static protocal map for the particular serdes config we are in. This makes is_serdes_configured() much simplier and not constantly reading registers to determine if a given device is enabled based on the protocol. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-21powerpc/85xx: Rework MPC8536 SERDES is_serdes_configured supportKumar Gala
Move serdes init until after we are in ram so we can keep track of a global static protocal map for the particular serdes config we are in. This makes is_serdes_configured() much simplier and not constantly reading registers to determine if a given device is enabled based on the protocol. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20powerpc/p3041: Add various p3041 related definesKumar Gala
There are various locations that we have chip specific info: * Makefile for which ddr code to build * Added p3041 to cpu_type_list and SVR list * Added number of LAWs for p3041 * Set CONFIG_MAX_CPUS to 4 for p3041 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20powerpc/p5020: Add various p5020 related defines (and p5010)Kumar Gala
There are various locations that we have chip specific info: * Makefile for which ddr code to build * Added p5020 & p5010 to cpu_type_list and SVR list * Added number of LAWs for p5020 * Set CONFIG_MAX_CPUS to 2 for p5020 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20powerpc/mpc85xx: Report FMAN # to match user manualEmil Medve
The user manual refers to FMAN1 and FMAN2 not 0 and 1. Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20powerpc/p4080: Add setting of clock-frequency for clockgen nodeKumar Gala
On QorIQ CoreNet based devices we have a global clocking block. We want to keep track of SYSCLK frequency as it is what is used to derive all other frequencies in the SoC Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20powerpc/85xx: Use fdt_node_offset_by_compat_reg for clock-frequency updatesKumar Gala
Move to using fdt_node_offset_by_compat_reg to find the node offsets we want to update instead of using aliases. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-17Drop support for GTH boardWolfgang Denk
The board maintainer states: The GTH board is obsolete and has not been manufactured for several years. To my knowledge, no recent U-Boot build has been tested on that card. So drop support for this board. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Thomas Lange <thomas@corelatus.se> Acked-by: Thomas Lange<thomas@corelatus.se>
2010-07-16powerpc/85xx: Move p1022ds slot code into board fileKumar Gala
The code to map SERDES configs to slot names is board specific and not chip specific. Thus it should live in board/freescale/p1022ds/ and not in arch/powerpc/cpu/. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16powerpc/85xx: Add command to report errata workaroundsKumar Gala
Add 'errata' command to report what errata we workaround. Report workaround for erratum SATA-A001 on P1022/P1013. Also sorted the CONFIG_CMD_* list. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16powerpc: add support for the Freescale P1022DS reference boardTimur Tabi
Specifics: 1) 36-bit only 2) Booting from NOR flash only 3) Environment stored in NOR flash only 4) No SPI support 5) No DIU support Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16powerpc/85xx: Add recognition of e5500 coreKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2024-12-28 16:24:58 +0000