summaryrefslogtreecommitdiff
path: root/arch/powerpc/include/asm/config_mpc85xx.h
AgeCommit message (Collapse)Author
2012-04-24powerpc/srio: Rewrite the struct ccsr_rioLiu Gang
Rewrite this struct for the support of two ports and two message units registers. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2011-11-29powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.hTimur Tabi
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA controller, so it should be defined in config_mpc85xx.h instead of the various board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013, P1022, P2041, P3041, P5010, and P5020. It was already defined for the P1010 and P1014. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29powerpc/85xx: Add workaround for erratum A-003474York Sun
Erratum A-003474: Internal DDR calibration circuit is not supported Impact: Experience shows no significant benefit to device operation with auto-calibration enabled versus it disabled. To ensure consistent timing results, Freescale recommends this feature be disabled in future customer products. There should be no impact to parts that are already operating in the field. Workaround: Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following: 1. Write a value of 0x0000_0015 to the register at offset CCSRBAR + DDR OFFSET + 0xf30 2. Write a value of 0x2400_0000 to the register at offset CCSRBAR + DDR OFFSET + 0xf54 Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29powerpc/85xx: Add workaround for erratum CPU-A003999Kumar Gala
Erratum A-003999: Running Floating Point instructions requires special initialization. Impact: Floating point arithmetic operations may result in an incorrect value. Workaround: Perform a read modify write to set bit 7 to a 1 in SPR 977 before executing any floating point arithmetic operation. This bit can be set when setting MSR[FP], and can be cleared when clearing MSR[FP]. Alternatively, the bit can be set once at boot time, and never cleared. There will be no performance degradation due to setting this bit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129chenhui zhao
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early verion silicons. This workaround detects if the eTSEC Rx logic is properly initialized, and reinitialize the eTSEC Rx logic. Signed-off-by: Gong Chen <g.chen@freescale.com> Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03powerpc/p3060: Add SoC related support for P3060 platformShengzhou Liu
Add P3060 SoC specific information:cores setup, LIODN setup, etc The P3060 SoC combines six e500mc Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral interfaces. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03powerpc/mpc8548: Add workaround for erratum NMG_LBC103Kumar Gala
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document. Any local bus transaction may fail during LBIU resynchronization process when the clock divider [CLKDIV] is changing. Ensure there is no transaction on the local bus for at least 100 microseconds after changing clock divider LCRR[CLKDIV]. Refer to the erratum LBIU3 of mpc8548. Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03powerpc/mpc8548: Add workaround for erratum NMG_DDR120Kumar Gala
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some early version silicons. The default settings of the DDR IO receiver biasing may not work at cold temperature. When a failure occurs, a DDR input latches an incorrect value. The workaround will set the receiver to an acceptable bias point. Signed-off-by: Gong Chen Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)Poonam Aggrwal
Issue: Address masking doesn't work properly. When sum of the base address, defined by BA, and memory bank size, defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask CSPRn[BA] bits. Impact: This will impact booting when we are reprogramming CSPR0(BA) and AMASK0(AMASK) while executing from NOR Flash. Workaround: Re-programming of CSPR(BA) and AMASK is done while not executing from NOR Flash. The code which programs the BA and AMASK is executed from L2-SRAM. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)Poonam Aggrwal
Issue: Peripheral connected to IFC_CS3 may hamper booting from IFC. Impact: Boot from IFC may not be successful if IFC_CS3 is used. Workaround: If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR. Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)Poonam Aggrwal
Issue: The NOR-FCM does not support access to unaligned addresses for 16 bit port size Impact: When 16 bit port size is used, accesses not aligned to 16 bit address boundary will result in incorrect data Workaround: The workaround is to switch to GPCM mode for NOR Flash access. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macrosTimur Tabi
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS. This is necessary for the assembly-language code that relocates CCSR, since the assembler does not understand 64-bit constants. CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it should not be defined in a board header file. Similarly, CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so it should also not be defined in the board header file. CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT, and so CCSR will not be relocated. Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot builds (e.g. NAND) are required to relocate CCSR only during the last stage (i.e. the "real" U-Boot). All other stages should define CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated. README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0Kumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014Ramneek Mehresh
Add UTMI and ULPI PHY support for USB controller on qoriq series of processors with internal UTMI PHY implemented, for example P1010/P1014 - Use both getenv() and hwconfig to get USB phy type till getenv() is depricated - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc has internal UTMI phy Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11powerpc/85xx: Add P2041 processor supportKumar Gala
The P2041 is similar to P2040, however has a 10G port and backside L2 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-20powerpc/fsl_pci: Fix device tree fixups for newer platformsKumar Gala
We assumed that only a small set of compatiable strings would be needed to find the PCIe device tree nodes to be fixed up. However on newer platforms the simple rules no longer work. We need to allow specifying the PCIe compatiable string for each individual SoC. We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if the default isn't sufficient. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Change timebase divisor to be defined per processorKumar Gala
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because different SoCs have different divisor amounts. All the PQ3 parts are /8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001Timur Tabi
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1 are swapped. Erratum SERDES-A001 says that if bank two is kept disabled and after bank three is enabled, then the PLL for bank three won't lock properly. The work-around is to enable and then disable bank two after bank three is enabled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005Timur Tabi
SerDes PLL bandwidth default setting is incorrect when no lanes are configured as PCI Express. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc/85xx: Enable ESDHC111 erratum on P2040/P3041/P5010/P5020 SoCsLei Xu
The workaround for ESDHC111 should also be applied on P2040/P3041/P5010/P5020 SoCs. Signed-off-by: Lei Xu <B33228@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020Roy Zang
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we need to enable for them to function. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27p4080/serdes: Implement the XAUI workaround for SERDES9 erratumEmil Medve
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10fsl_esdhc: Deal with watermark level register related changesPriyanka Jain
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark level register description has been changed: 9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00 25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang
P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Fixup determining PME, FMan freqKumar Gala
On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some additional rules to determining the various frequencies that PME & FMan IP blocks run at. We need to take into account: * Reduced number of Core Complex PLL clusters * HWA_ASYNC_DIV (allows for /2 or /4 options) On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs the PME & FMan blocks utilize the second Core Complex PLL. On SoCs like p4080 with 4 Core Complex PLLs we utilize the third Core Complex PLL for PME & FMan blocks. On P2040/P3041/P5020 we have the added feature that we can divide the PLL down further by either /2 or /4 based on HWA_ASYNC_DIV. On P4080 this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be set to 0 and this gets a backward compatiable /2 behavior. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Specify CONFIG_SYS_FM_MURAM_SIZEKumar Gala
CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in config_mpc85xx.h for those parts with a Frame Manager. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Adds some P1010/P1014 SoC configuration definesPoonam Aggrwal
Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR and SDHC erratum. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Support for Freescale P1024/P1025 processorKumar Gala
Add Support for Freescale P1024/P1025 (dual core) and P1015/P1016 (single core) processors. P1024 is a variant of P1020 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1025 is a variant of P1021 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1015 is a variant of P1024 processor with single core and P1016 is a variant of P1025 processor with single core. Added comments in config_mpc85xx.h to denote single core versions of processors. Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Add support for Freescale P1023/P1017 ProcessorsRoy Zang
Add P1023 (dual core) & P1017 (single core) specific information: * SERDES Table * Added P1023/P1017 to cpu_type_list and SVR list (fixed issue with P1013 not being sorted correctly). * Added P1023/P1027 to config_mpc85xx.h * Added new LAW type introduced on P1023/P1017 * Updated a few immap register/defines unique to P1023/P1017 Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Cleanup some QE related definesKumar Gala
Move some processor specific QE defines into config_mpc85xx.h and use QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct. Also fixed up some comment style issues in immap_qe.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020Kumar Gala
Specify the number of DDR controllers, number of frame managers, number of 1g and 10g ports. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-29powerpc/85xx: Handle PCIe initialization requires for P1021 class SoCsPrabhakar Kushwaha
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require that we initialize the SERDES registers if the lanes are configured for PCIe. Additionally these devices PCIe controller do not support ASPM and we have to explicitly disable it. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-28powerpc/85xx: Enable various errata on P1022/P1013 SoCsJiang Yutang
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on P1022/P1013 SoCs. Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2. Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134York Sun
Workaround for the following errata: DDR111 - MCKE signal may not function correctly at assertion of HRESET DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can calibrate to incorrect values These two workarounds must be implemented together because they touch common registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/85xx: Rename MPC8572 DDR erratum to DDR115York Sun
Use unique erratum number instead of platform number. Enable command that reports errata on MPC8572DS. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)Kumar Gala
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8, and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/85xx: Enable ESDHC111 Erratum on P2010/P2020 SoCsKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-02Minor Coding Style Cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-01-19mpc85xx: Implement workaround for erratum DDR-A003York Sun
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM. Also adding polling after enabling DDR controller to ensure completion. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headersKumar Gala
Add new headers that capture common defines for a given SoC/processor rather than duplicating that information in board config.h and random other places. Eventually this should be handled by Kconfig & defconfigs Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
generated by cgit (git 2.34.1) at 2024-12-28 08:07:09 +0000