Age | Commit message (Collapse) | Author |
|
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
|
|
Remove getting values of usb mode and phy_type from "usb_dr_mode"
and "usb_phy_type" uboot env variables. Now, these are determined
only from hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
It is not necessary for all processor to have serdes block 1 & 2.
They may have only one serdes block.
So, put serdes block 1 & 2 related code under defines
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
|
|
Fix the license header introduced by the following patches
Add TWR-P10xx board support
Add T4240EMU target
IDT8T49N222A configuration code
Add C29x SoC support
Add support for C29XPCIE board
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Fix the following build error caused by patch "powerpc/pcie: add PCIe
version 3.x support":
pcie.c:302:34: error: 'PCI_LTSSM' undeclared (first use in this function)
pcie.c:303:15: error: 'PCI_LTSSM_L0' undeclared (first use in this function)
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
The TIMING_CFG_3[EXT_ACTTOPRE] register field is 2 bits wide, but
the mask omitted the LSB. This patch provides a 2-bit wide mask.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engine. There're
three SoC types(C291, C292, C293) with the following features:
- 512K L2 Cache/SRAM and 512 KB platform SRAM
- DDR3/DDR3L 32bit DDR controller
- One PCI express (x1, x2, x4) Gen 2.0 Controller
- Trust Architecture 2.0
- SEC6.0 engine
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
|
|
B4860 and B4420 has PCIe version 2.4 IP instead of 3.x
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
It allows files not in the same path to use this function
as required by B4 board file
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
|
|
Also change the define name SRDS_RSTCTL_SDPD to
SRDS_RSTCTL_SDEN, which stands for SerDes enable
as mentioned in SerDes module guide
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
|
|
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
When a board (slave) boots from SRIO/PCIE, it would get the instructions
from a remote board (master) by SRIO/PCIE interface, and the slave's
u-boot image should be built with the
SYS_TEXT_BASE=0xFFF80000;
So the u-boot of the slave should avoid the NOR_BOOT branch at the
booting stage.
For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB
entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000",
and with the 4M size as the boot window in NOR_BOOT branch. Because
the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so
the TLB entry will be from base address 0xffc00000 and with 4M size.
Then the u-boot will set TLB entry 14 from base address
"CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial
stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR
= 0xffd00000. So the TLB entry 14 and 15 will be in confliction.
There will be right TLB entries configurations when avoid the
NOR_BOOT branch and set the boot window from 0xfff00000 with 1M
size space.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
|
|
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.
Tested on MT36JSF2G72PZ-1G9E1 RDIMM.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
When chip select interleaving is enabled, cs0_bnds is used for address
binding. Other csn_bnds are not used. When two controllers interleaving is
enabled, cs0_bnds of both controllers are used, other csn_bnds are not.
However, the unused csn_bnds may be used internally for calculating
addresses for calibration. Setting those registers to 0 may confuse
controllers in some cases. Instead, setting them to 0xffffffff together
with normal LAWs will guarantee the address is not mapped to DDR.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
The RCW print is common for all corenet platforms. Not necessary to ducplicate
in each board file.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
For T4 platform, the SRIO LIODN registers are in SRIO address space
and not in GUTs.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
|
|
For B4, the SRIO LIODN registers are in SRIO address space and not
in GUTs.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
|
|
For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.
In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter
framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX
is only used on the keymile boards, and they are now completely
moved to the new framework, remove CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
|
|
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
|
|
CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs.
CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need
of disable_tlb().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication]
breaks booting Linux (compressed uImage with fdt) on powerpc.
boot_jump_linux() mustn't be called before boot_prep_linux() and
boot_body_linux() have been called. So remove the superfluous call
to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on
in this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
|
|
P1023RDB Specification:
-----------------------
Memory subsystem:
512MB DDR3 (Fixed DDR on board)
64MB NOR flash
128MB NAND flash
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC2: Connected to Atheros AR8035 GETH PHY
PCIe:
Three mini-PCIe slots
USB:
Two USB2.0 Type A ports
I2C:
AT24C08 8K Board EEPROM (8 bit address)
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
init_tlbs() initialize all the TLB entries required for the system.
So disable DEBUG TLB entry before TLB entries initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
If a variable is used as array subscript, it's valid value range is
0 ... ARRAY_SIZE -1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
address of the BSS
There will clear the BSS in the function clear_bss(), the reset address of
the BSS started from the __bss_start, and increased by four-byte increments,
finally stoped depending on the address is equal to the _bss_end. If the end
address __bss_end is not alignment to 4byte, it will be an infinite loop.
1. The reset action stoped depending on the reset address is greater
than or equal the end address of the BSS.
2. The end address of the BSS should be 4byte aligned. Because the reset unit
is 4 Bytes.
This patch is on top of the patch "powerpc/mpc85xx: support application
without resetvec segment in the linker script".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
script
For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM,
then jump to it to begin execution. After that, the SPL loads the final uboot
image into DDR, then jump to it to begin execution. The segment .resetvec in
the SPL and in final U-boot is useless.
So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application.
If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded
and the segment .bootpg is placed in the previous 4K of the segment .text.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
All the other constants use lowercase 'x' in "MPC85xx", so we
duplicate that here.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Freescale documentation presents the PowerPC core names in lower case, such as
"e300", "e500", "e600", etc.
Change the upper case occurrences into lower case so that the core names
reported in U-boot can match the ones from the documentation.
While at it also fix a checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81:
+ printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 );
Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
BSC9132 has 3 IFC banks.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|