summaryrefslogtreecommitdiff
path: root/arch/powerpc
AgeCommit message (Collapse)Author
2013-02-01ppc: Remove extra pci_clk fields from global_dataSimon Glass
PPC has several of these fields, selected by chip type, although only one is ever compiled in. Instead, use a single field. It would be nice if this could be selected by CONFIG_PCI, but some chips (e.g. mpc5xxx) use pci_clk even when CONFIG_PCI is not enabled. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01ppc: Move brg_clk to arch_global_dataSimon Glass
Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01Add architecture-specific global dataSimon Glass
We plan to move architecture-specific data into a separate structure so that we can make the rest of it common. As a first step, create struct arch_global_data to hold these fields. Initially it is empty. This patch applies to all archs at once. I can split it if this is really a pain. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-01-30powerpc/t4240: Adding workaround errata A-005871Shengzhou Liu
When CoreNet Fabric (CCF) internal resources are consumed by the cores, inbound SRIO messaging traffic through RMan can put the device into a deadlock condition. This errata workaround forces internal resources to be reserved for upstream transactions. This ensures resources exist on the device for upstream transactions and removes the deadlock condition. The Workaround is for the T4240 silicon rev 1.0. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: Add property 'fsl, sec-era' in device tree node 'crypto'Vakul Garg
If property 'fsl,sec-era' is already present, it is updated. This property is required so that applications can ascertain which descriptor commands are supported on a particular CAAM version. Signed-off-by: Vakul Garg <vakul@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30mpc8xxx: fix DDR init value to use CONFIG_MEM_INIT_VALUEAnatolij Gustschin
Configuring custom memory init value using CONFIG_MEM_INIT_VALUE in the board config file doesn't work and memory is always initialized to the value 0xdeadbeef. Only use this default value if a board doesn't define CONFIG_MEM_INIT_VALUE. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andy Fleming <afleming@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: add support for MMUv2 page sizesScott Wood
e6500 implements MMUv2 and supports power-of-2 page sizes rather than power-of-4. Add support for such pages. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: Add BSC9132/BSC9232 processor supportPrabhakar Kushwaha
The BSC9132 is a highly integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments. The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850 core technologies with MAPLE-B2P baseband acceleration processing elements to address the need for a high performance, low cost, integrated solution that handles all required processing layers without the need for an external device except for an RF transceiver or, in a Micro base station configuration, a host device that handles the L3/L4 and handover between sectors. The BSC9132 SoC includes the following function and features: - Power Architecture subsystem including two e500 processors with 512-Kbyte shared L2 cache - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2 cache - 32 Kbyte of shared M3 memory - The Multi Accelerator Platform Engine for Pico BaseStation Baseband Processing (MAPLE-B2P) - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including ECC), up to 1333 MHz data rate - Dedicated security engine featuring trusted boot - Two DMA controllers - OCNDMA with four bidirectional channels - SysDMA with sixteen bidirectional channels - Interfaces - Four-lane SerDes PHY - PCI Express controller complies with the PEX Specification-Rev 2.0 - Two Common Public Radio Interface (CPRI) controller lanes - High-speed USB 2.0 host and device controller with ULPI interface - Enhanced secure digital (SD/MMC) host controller (eSDHC) - Antenna interface controller (AIC), supporting four industry standard JESD207/four custom ADI RF interfaces - ADI lanes support both full duplex FDD support & half duplex TDD - Universal Subscriber Identity Module (USIM) interface that facilitates communication to SIM cards or Eurochip pre-paid phone cards - Two DUART, two eSPI, and two I2C controllers - Integrated Flash memory controller (IFC) - GPIO - Sixteen 32-bit timers Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc8xxxx: FSL DDR debugger auto run of stored commandsJames Yang
This patch adds the ability for the FSL DDR interactive debugger to automatically run the sequence of commands stored in the ddr_interactive environment variable. Commands are separated using ';'. ddr_interactive=compute; edit c0 d0 dimmparms caslat_X 0x3FC0; go Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30Add copy command to FSL DDR interactiveJames Yang
Add copy command which allows copying of DIMM/controller settings. This saves tedious retyping of parameters for each identical DIMM or controller. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30Fix data stage name matching issueJames Yang
This fix allows the name of the stage to be specifed after the controler and DIMM is specified. Prior to this fix, if the data stage name is not the first entry on the command line, the operation is applied to all controller and DIMMs. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30Move DDR command parsing to separate functionJames Yang
Move the FSL DDR prompt command parsing to a separate function so that it can be reused. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc8xxx: Enable entering DDR debugging by key pressYork Sun
Using environmental variable "ddr_interactive" to activate interactive DDR debugging seomtiems is not enough. For example, after updating SPD with a valid but wrong image, u-boot won't come up due to wrong DDR configuration. By enabling key press method, we can enter debug mode to have a chance to boot without using other tools to recover the board. CONFIG_FSL_DDR_INTERACTIVE needs to be defined in header file. To enter the debug mode by key press, press key 'd' shortly after reset, like one would do to abort auto booting. It is fixed to lower case 'd' at this moment. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx:Fix Core cluster configuration loopPrabhakar Kushwaha
Different personalities/derivatives of SoC may have reduced cluster. But it is not necessary for last valid DCFG_CCSR_TP_CLUSTER register to have DCFG_CCSR_TP_CLUSTER[EOC] bit set to represent "End of Clusters". EOC bit can still be set in last DCFG_CCSR_TP_CLUSTER register of orignal SoC which may not be valid for the personality. So add initiator type check to find valid cluster. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx:Add support of B4420 SoCPoonam Aggrwal
B4420 is a reduced personality of B4860 with fewer core/clusters(both SC3900 and e6500), fewer DDR controllers, fewer serdes lanes, fewer SGMII interfaces and reduced target frequencies. Key differences between B4860 and B4420 ---------------------------------------- B4420 has: 1. Fewer e6500 cores: 1 cluster with 2 e6500 cores 2. Fewer SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster. 3. Single DDRC 4. 2X 4 lane serdes 5. 3 SGMII interfaces 6. no sRIO 7. no 10G Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: Few updates for B4860 cpu changesPoonam Aggrwal
- Added some more serdes1 and serdes2 combinations serdes1= 0x2c, 0x2d, 0x2e serdes2= 0x7a, 0x8d, 0x98 - Updated Number of DDR controllers to 2. - Added FMAN file for B4860, drivers/net/fm/b4860.c Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: Reserve default boot pageYork Sun
The boot page in memory is already reserved so OS won't overwrite. As long as the boot page translation is active, the default boot page also needs to be reserved in case the memory is 4GB or more. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-12-19powerpc/mpc83xx: add support for new SPLScott Wood
This adds arch support for PPC mpc83xx to boot "minimal" (4K) SPLs using the new infrastructure. Existing nand_spl targets are updated to deal with the name change from nand_init.c to spl_minimal.c (as in theory this isn't limited to NAND anymore). Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-12-13env: Use getenv_yesno() more generallyJoe Hershberger
Move the getenv_yesno() to env_common.c and change most checks for 'y' or 'n' to use this helper. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-12-11Add strcasecmp() and strncasecmp()Simon Glass
strncasecmp() is present as strnicmp() but disabled. Make it available and define strcasecmp() also. There is a only a small performance penalty to having strcasecmp() call strncasecmp(), so do this instead of a standalone function, to save code space. Update the prototype in arch-specific headers as needed to avoid warnings. Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-05mpc5200: Add SPL supportStefan Roese
This patch adds SPL booting support (NOR flash) for the MPC5200 platforms. Signed-off-by: Stefan Roese <sr@denx.de>
2012-12-05SPL: Port SPL framework to powerpcStefan Roese
This patch enables the SPL framework to be used on powerpc platforms and not only ARM. timer_init() does not exist on PPC systems. The timer (decrementer) is initialized and enabled in interrupt_init() here. And currently interrupt_init() is called after relocation to SDRAM. Since the only powerpc SPL implementation (a3m071) doesn't need a timer, let's remove this timer_init() call for PPC systems. Signed-off-by: Stefan Roese <sr@denx.de>
2012-12-05powerpc: Extract EPAPR_MAGIC constants into processor.hStefan Roese
By extracting these defines into a header, they can be re-used by other C sources as well. This will be done by the SPL framework OS boot support. Signed-off-by: Stefan Roese <sr@denx.de>
2012-11-27powerpc/mpc85xx: Fix a bug introduced by CONFIG_PPC_SPINTABLE_COMPATIBLEYork Sun
Fix a bug introduced by this patch powerpc/mpc85xx: Temporary fix for spin table backward compatibility Should have checked both CONFIG_PPC_SPINTABLE_COMPATIBLE and CONFIG_MP in cpu_init.c. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/85xx: update the work-around for P4080 erratum SERDES-9Timur Tabi
The documented work-around for P4080 erratum SERDES-9 has been updated. It is now compatible with the work-around for erratum A-4580. This requires adding a few bitfield macros for the BnTTLCRy0 register. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/p4080ds: fix PCI-e x8 link training down failureYuanquan Chen
Due to SerDes configuration error, if we set the PCI-e controller link width as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to PCI-e slot, it fails to train down to the PCI-e device's link width. According to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between RC and EP. Signed-off-by: Yuanquan Chen <B41889@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/corenet_ds: move SATA config to board configurationZang Roy-R61911
board configuration file is included before asm/config_mpc85xx.h. however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h. it will never take effective in the board configuration file for this kind of code : #ifdef CONFIG_FSL_SATA_V2 ... #endif To solve this problem, move CONFIG_FSL_SATA_V2 to board configuration header file. This patch reverts Timur's commit:3e0529f742e893653848494ffb9f7cd0d91304bf Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/85xx: implement check for erratum A-004580 work-aroundTimur Tabi
The work-around for erratum A-004580 ("Internal tracking loop can falsely lock causing unrecoverable bit errors") is implemented via the PBI (pre-boot initialization code, typically attached to the RCW binary). This is because the work-around is easier to implement in PBI than in U-Boot itself. It is still useful, however, for the 'errata' command to tell us whether the work-around has been applied. For A-004580, we can do this by verifying that the values in the specific registers that the work-around says to update. This change requires access to the SerDes lane sub-structure in serdes_corenet_t, so we make it a named struct. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/mpc8xxx: take fdt_fixup_crypto_node() off the checkstack listKim Phillips
by moving compat_strlist into the .bss section. 0xfe004d80 fdt_fixup_crypto_node [u-boot]: 264 Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/mpc85xx: Temporary fix for spin table backward compatibilityYork Sun
Once u-boot sets the spin table to cache-enabled memory, old kernel which uses cache-inhibit mapping without coherence will not work properly. We use this temporary fix until kernel has updated its spin table code. For now this fix is activated by default. To disable this fix for new kernel, set environmental variable "spin_table_compat=no". After kernel has updated spin table code, this default shall be changed. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/85xx: implement check for erratum A-004849 work-aroundTimur Tabi
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a deadlock under certain traffic patterns causing the system to hang") is implemented via the PBI (pre-boot initialization code, typically attached to the RCW binary). This is because the work-around is easier to implement in PBI than in U-Boot itself. It is still useful, however, for the 'errata' command to tell us whether the work-around has been applied. For A-004849, we can do this by verifying that the values in the specific registers that the work-around says to update. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27powerpc/85xx/p5040: add CONFIG_SYS_PPC64, del CONFIG_SYS_FSL_ELBC_MULTIBIT_ECCTimur Tabi
The P5040 has an e5500 core, so CONFIG_SYS_PPC64 should be defined in config_mpc85xx.h. This macro was absent in the initial P5040 patch because it crossed paths with the patch that introduced the macro. Also delete CONFIG_SYS_FSL_ELBC_MULTIBIT_ECC, since it's not used in the upstream U-Boot. It's a holdover from the SDK. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-278xxx: Change all 8*xx_DDR addresses to 8xxxAndy Fleming
There were a number of shared files that were using CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and several variants (DDR2, DDR3). A recent patchset added 85xx-specific ones to code which was used by 86xx systems. After reviewing places where these constants were used, and noting that the type definitions of the pointers assigned to point to those addresses were the same, the cleanest approach to fixing this problem was to unify the namespace for the 85xx, 83xx, and 86xx DDR address definitions. This patch does: s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g All 85xx, 86xx, and 83xx have been built with this change. Signed-off-by: Andy Fleming <afleming@freescale.com> Tested-by: Andy Fleming <afleming@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-26Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini
2012-11-26spl/85xx: new SPL supportScott Wood
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once the last mpc85xx nand_spl target is gone. CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't seem right to overload it for meaning SPL as well as nand_spl does. Even if it's somewhat appropriate for the main u-boot, the SPL itself isn't (necessarily) ramboot, and we don't have separate configs for SPL and main u-boot. It was also inconsistent, as other platforms such as mpc83xx didn't use CONFIG_RAMBOOT in this way. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/powerpc: introduce CONFIG_SPL_INIT_MINIMALScott Wood
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific. Signed-off-by: Scott Wood <scottwood@freescale.com> --- v2: factor out START, and change cpu_init_nand.c to spl_minimal.c Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx: consistently use COBJS-yScott Wood
A subsequent patch will conditionalize some of the files that are currently unconditional. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/mpc85xx: rename cpu_init_nand.c to spl_minimal.cScott Wood
There is nothing really NAND-specific about this file. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/mpc85xx: move udelay to cpu codeScott Wood
It applies to non-Freescale 85xx boards as well as Freescale boards, so it doesn't belong in board/freescale. Plus, it needs to come out of nand_spl if it's to be used by the new SPL. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc8xxx: move LAW code into arch/powerpc/cpu/mpc8xxxScott Wood
It's arch code and not a driver, so move it where it belongs. When it originally went into drivers/misc there was no 8xxx CPU directory. This will make new-SPL support a little easier since we can keep the CPU stuff together and not need to pull stuff in from drivers/misc. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx: fix TLB alignmentScott Wood
In the RAMBOOT/SPL case we were creating a TLB entry starting at CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly aligned for the TLB entry size. This turned out to not be the case with NAND SPL because the main U-Boot starts at an offset into the image in order to skip the SPL itself. Fix the TLB entry to always start at a proper alignment. We still assume that CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary thus requiring multiple TLB entries. Signed-off-by: Scott Wood <scottwood@frescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc: change .fixup test to a GCC version testScott Wood
This was introduced by commit 244615197469dd6fe75ae082f38424b97c79aeaf, but it fails in a minimal SPL build where the only thing in arch/powerpc/lib is cache.c, which apparently doesn't generate any fixup records. The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer. Patterned after checkthumb as suggested by Tom Rini. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Tom Rini <trini@ti.com> -- v2: test gcc version instead of testing nothing
2012-11-26powerpc/mpc85xx: add comma before "already enabled"Scott Wood
Now outputs like this: L2: 512 KB already enabled, moving to 0xf8f80000 rather than this: L2: 512 KB already enabledmoving to 0xf8f80000 Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@gmail.com>
2012-11-26powerpc/mpc85xx: move debug tlb entry after TLB is in known stateScott Wood
Previously, in many if not all configs we were creating overlapping TLB entries which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL into L2 SRAM. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Andy Fleming <afleming@freescale.com> -- Prabhakar, please test that debug still works.
2012-11-20usb: use linux/usb/ch9.h instead of usbdescriptors.hIlya Yanok
Linux usb/ch9.h seems to have all the same information (and more) as usbdescriptors.h so use the former instead of the later one. As a consequense of this change USB_SPEED_* values don't correspond directly to EHCI speed encoding anymore, I've added necessary recoding in EHCI driver. Also there is no point to put speed into pipe anymore so it's removed and a bunch of host drivers fixed to look at usb_device->speed instead. Old usbdescriptors.h included is not removed as it seems to be used by old USB device code. This makes usb.h and usbdevice.h incompatible. Fortunately the only place that tries to include both are the old MUSB code and it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute on musb_regs structure but this attribute seems to be unneeded (old MUSB code doesn't support any DMA at all). Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-04powerpc/mpc83xx: sparse fixesKim Phillips
fdt.c:91:78: warning: Using plain integer as NULL pointer fdt.c:103:78: warning: Using plain integer as NULL pointer speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static? speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static? mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04powerpc/mpc85xx: sparse fixesKim Phillips
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static? cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static? bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart' bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write' bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write' bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio' bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write' bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write' bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec' bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect' ngpixis.c:245:1: error: directive in argument list ngpixis.c:247:1: error: directive in argument list Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04arch/powerpc/cpu/mpc8xxx/: sparse fixesKim Phillips
ctrl_regs.c:31:5: warning: symbol 'fsl_ddr_get_version' was not declared. Should it be static? cpu.c:135:14: warning: non-ANSI function declaration of function 'cpu_mask' cpu.c:154:18: warning: non-ANSI function declaration of function 'cpu_numcores' cpu.c:37:17: warning: symbol 'cpu_type_list' was not declared. Should it be static? cpu.c:117:17: warning: symbol 'cpu_type_unknown' was not declared. Should it be static? fsl_lbc.c:14:6: warning: symbol '__lbc_sdram_init' was not declared. Should it be static? and: lc_common_dimm_params.c:15:1: warning: symbol 'compute_cas_latency_ddr3' was not declared. Should it be static? making it static produces the following compiler warning: lc_common_dimm_params.c:15:1: warning: 'compute_cas_latency_ddr3' defined but not used [-Wunused-function] so we protect it with the preprocessor. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04arch/powerpc/lib/board.c, *traps.c: sparse fixesKim Phillips
traps.c:*:1: warning: symbol 'print_backtrace' was not declared. Should it be static? traps.c:93:1: warning: symbol '_exception' was not declared. Should it be static? board.c:166:6: warning: symbol '__board_add_ram_info' was not declared. Should it be static? board.c:174:5: warning: symbol '__board_flash_wp_on' was not declared. Should it be static? board.c:187:6: warning: symbol '__cpu_secondary_init_r' was not declared. Should it be static? board.c:265:12: warning: symbol 'init_sequence' was not declared. Should it be static? board.c:348:5: warning: symbol '__fixup_cpu' was not declared. Should it be static? board.c:405:53: warning: Using plain integer as NULL pointer Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04arch/powerpc/lib/extable.c: sparse fixKim Phillips
extable.c:66:9: warning: symbol 'ex_tab_message' was not declared. Should it be static? making it static can produce a new build warning on some boards: extable.c:66:12: warning: 'ex_tab_message' defined but not used [-Wunused-variable] but ex_tab_message doesn't do much even when used, so just remove it. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-30 22:45:29 +0000