summaryrefslogtreecommitdiff
path: root/arch/riscv
AgeCommit message (Collapse)Author
2020-07-01riscv: Add Sipeed Maix supportSean Anderson
The Sipeed Maix series is a collection of boards built around the RISC-V Kendryte K210 processor. This processor contains several peripherals to accelerate neural network processing and other "ai" tasks. This includes a "KPU" neural network processor, an audio processor supporting beamforming reception, and a digital video port supporting capture and output at VGA resolution. Other peripherals include 8M of sram (accessible with and without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256 accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix peripherals vary, but include spi flash; on-board usb-serial bridges; ports for cameras, displays, and sd cards; and ESP32 chips. Currently, only the Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly similar. Documentation for Maix boards is located at <http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is located at <https://kendryte.com/downloads/>. However, hardware details are rather lacking, so most technical reference has been taken from the standalone sdk located at <https://github.com/kendryte/kendryte-standalone-sdk>. Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-07-01riscv: Add device tree for K210 and Sipeed Maix BitMSean Anderson
Where possible, I have tried to find compatible drivers based on the layout of registers. However, many devices remain untested. All untested devices have been left disabled, but some tentative properties (such as compatible strings, and clocks, interrupts, and resets properties) have been added. Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-07-01riscv: Allow use of reset driversSean Anderson
Currently, one cannot use a reset driver on RISC-V. Follow the MIPS example, and disable the default reset handler when the sysreset driver is enabled. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-01riscv: Add option to support RISC-V privileged spec 1.9Sean Anderson
Some older processors (notably the Kendryte K210) use an older version of the RISC-V privileged specification. The primary changes between the old and new are in virtual memory, and in the merging of three separate counter enable CSRs. Using the new CSR on an old processor causes an illegal instruction exception. This patch adds an option to use the old CSRs instead of the new one. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-01riscv: Clean up IPI initialization codeSean Anderson
The previous IPI code initialized the device whenever the first call was made to a riscv_*_ipi function. This made it difficult to determine when the IPI device was initialized. This patch introduces a new function riscv_init_ipi. It is called once during arch_cpu_init_dm. In SPL, it is called in spl_invoke_opensbi. Before this point, no riscv_*_ipi functions should be called. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-07-01riscv: Clear pending interrupts before enabling IPIsSean Anderson
On some platforms (k210), the previous stage bootloader may have not cleared pending IPIs before transferring control to U-Boot. This can cause race conditions, as multiple harts all attempt to initialize the IPI controller at once. This patch clears IPIs before enabling them, ensuring that only one hart modifies shared memory at once. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-07-01riscv: Add headers for asm/global_data.hSean Anderson
This header depended on bd_t and ulong, but did not include the appropriate headers. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-25bdinfo: riscv: Use generic bd_infoSimon Glass
At present riscv still uses its own private bd_info struct. Move it over to use the generic one like other archs. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-04riscv: sbi: Move sbi_probe_extension() out of CONFIG_SBI_V01Bin Meng
sbi_probe_extension() is an API defined in SBI v0.2, not v0.1. Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01") Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-06-04riscv: sbi: Remove sbi_spec_versionBin Meng
U-Boot defaults to use SBI v0.2. Howerver there is a global variable sbi_spec_version that stills refers to v0.1. Since it is not used anywhere, let's remove it. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-06-04riscv: sifive: fu540: add SPL configurationPragnesh Patel
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin) from MMC boot devices. SPL related code is leveraged from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: cpu: fu540: Add support for cpu fu540Pragnesh Patel
Add SiFive fu540 cpu to support RISC-V arch Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linuxPragnesh Patel
This sync has changes required to use GPIO in U-Boot and U-Boot SPL. Sync dts from linux v5.7-rc2 commit: "riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file" (sha1: 0a91330b2af9f71ceeeed483f92774182b58f6d9) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: sifive: dts: fu540: set ethernet clock ratePragnesh Patel
Set ethernet clock rate to 125 Mhz so that it will work with 1000Mbps, Earlier this is done by FSBL. With this change We can remove the ethernet clock rate code from FSBL. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-04riscv: sifive: dts: fu540: add U-Boot dmc nodePragnesh Patel
Add dmc node to enable ddr driver. dmc is used to initialize the memory controller. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04sifive: dts: fu540: Add DDR controller and phy register settingsPragnesh Patel
Add DDR controller and phy register settings, taken from fsbl (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: sifive: dts: fu540: Add board -u-boot.dtsi filesPragnesh Patel
Devicetree files in FU540 platform is synced from Linux, like other platforms does. Apart from these U-Boot in FU540 would also require some U-Boot specific node like clint. So, create board specific -u-boot.dtsi files. This would help of maintain U-Boot specific changes separately without touching Linux dts(i) files which indeed easy for syncing from Linux between releases. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: Add _image_binary_end for SPLPragnesh Patel
For SPL_SEPARATE_BSS, Device tree will be put at _image_binary_end Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: sifive: fu540: Use OTP DM driver for serial environment variablePragnesh Patel
Use the OTP DM driver to set the serial environment variable. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-05-26riscv: Move all SMP related SBI calls to SBI_v01Atish Patra
SMP support for S-mode U-Boot is enabled only if SBI_V01 is enabled. There is no point in supporting SMP related (IPI and fences) SBI calls when SBI_V02 is enabled. Modify all the SMP related SBI calls to be defined only for SBI_V01. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-18common: Drop linux/bitops.h from common headerSimon Glass
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop log.h from common headerSimon Glass
Move this header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18command: Remove the cmd_tbl_t typedefSimon Glass
We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop init.h from common headerSimon Glass
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop image.h from common headerSimon Glass
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop bootstage.h from common headerSimon Glass
Move this fairly uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop net.h from common headerSimon Glass
Move this header out of the common header. Network support is used in quite a few places but it still does not warrant blanket inclusion. Note that this net.h header itself has quite a lot in it. It could be split into the driver-mode support, functions, structures, checksumming, etc. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-04-30sifive: fu540: Enable spi-nor flash supportJagan Teki
HiFive Unleashed A00 support is25wp256 spi-nor flash, So enable the same and add test result log for future reference. Tested on SiFive FU540 board. Thanks to Sagar for various use cases and tests. [QUAD mode in dt with spi-tx-bus-width: <4>] pp opcode = 0x34 [QUAD MODE] read opcode = 0x6c [QUAD MODE] erase opcode = 0x21 SPI-NOR: 1. erase entire flash: Pass 2. write entire flash: Pass 3. read entire flash: Pass 4. cmp 32MiB read back data: Pass 5. MMC: Booted Linux and dtb from mmc [SPI MODE in dt with spi-tx-bus-width: <1>] pp opcode = 0x12 [SPI MODE] read opcode = 0xc [SPI MODE] erase opcode = 0x21 SPI-NOR: 1. erase entire flash: Pass 2. write entire flash: Pass 3. read entire flash: Pass 4. cmp 32MiB read back data: Pass 5. MMC: Booted Linux and dtb from mmc Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
2020-04-30riscv: dts: hifive-unleashed-a00: Add -u-boot.dtsiJagan Teki
Add U-Boot specific dts file for hifive-unleashed-a00, this would help to add u-boot specific properties and other node changes without touching the base dts(i) files which are easy to sync from Linux. Added spi2 alias for qspi2 as an initial u-boot specific property change. spi probing in current dm model is very much rely on aliases numbering. Even though the qspi2 can't come under any associated spi nor flash it would require to specify the same to make proper binding happen for other spi slaves. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
2020-04-23riscv: Move all fdt fixups togetherAtish Patra
Keep all the fdt fixups together for better code management. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: Copy the reserved-memory nodes to final DTAtish Patra
The DT used by U-Boot may be different from the DT being passed to the OS if the DT is loaded from external media such as network or mmc. In that case, the reserved-memory node needs to be copied to the DT passed to the OS. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: Setup reserved-memory node for FU540Atish Patra
FU540 uses OF_SEPARATE instead of OF_PRIOR_STAGE. Enable OF_BOARD_FIXUP to update the DT with reserved-memory node. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: Provide a mechanism to fix DT for reserved memoryAtish Patra
In RISC-V, M-mode software can reserve physical memory regions by setting appropriate physical memory protection (PMP) csr. As the PMP csr are accessible only in M-mode, S-mode U-Boot can not read this configuration directly. However, M-mode software can pass this information via reserved-memory node in device tree so that S-mode software can access this information. This patch provides a framework to copy to the reserved-memory node from one DT to another. This will be used to update the DT used by U-Boot and the DT passed to the next stage OS. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: Add boot hartid to device treeAtish Patra
Linux booting protocol mandates that register "a0" contains the hartid. However, U-Boot can not pass the hartid via a0 during standard UEFI protocol. DT nodes are commonly used to pass such information to the OS. Add a DT node under chosen node to indicate the boot hartid. EFI stub in Linux kernel will parse this node and pass it to the real kernel in "a0" before jumping to it. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: Make SBI v0.2 the default SBI versionBin Meng
To work with latest OpenSBI release (v0.7 or above) that has the HSM extension support, select the SBI v0.2 support by default. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-04-23riscv: Add Kconfig option for SBI v0.2Bin Meng
SBI v0.2 is more scalable and extendable to handle future needs for RISC-V supervisor interfaces. For example, with SBI v0.2 HSM extension, only a single hart need to boot and enter operating system. The booting hart can bring up secondary harts one by one afterwards. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-04-23riscv: Add SMP Kconfig option dependency for U-Boot properBin Meng
U-Boot proper running in S-mode only need SMP support when using SBI v0.1. With SBI v0.2 HSM extension, it does not need implement multicore boot in U-Boot proper. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-04-23riscv: Introduce SPL_SMP Kconfig option for U-Boot SPLBin Meng
With SBI v0.2 HSM extension, only a single hart need to boot and enter operating system. The booting hart can bring up secondary harts one by one afterwards. For U-Boot running in SPL, SMP can be turned on, while in U-Boot proper, SMP can be optionally turned off if using SBI v0.2 HSM. Introduce a new SPL_SMP Kconfig option to support this. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-04-23riscv: Merge unnecessary SMP ifdefs in start.SBin Meng
Two consecutive SMP ifdefs blocks can be combined into one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-04-23riscv: qemu: Remove the simple-bus driver for the SoC nodeBin Meng
Prior to QEMU v3.1.0, QEMU generated the 'virt' SoC node with a "riscv-virtio-soc" compatible string, and a "simple-bus" driver was created to accommodate that special case in U-Boot. Starting from QEMU v3.1.0, the SoC node was set as a "simple-bus", hence the special simple-bus driver is no longer needed. Update the doc to mention the latest tested QEMU version 4.2.0. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-23riscv: ax25: cache: Remove SPL_RISCV_MMODE config checkPragnesh Patel
CONFIG_IS_ENABLED(FOO) will check FOO config option for U-Boot, SPL and TPL, so remove unnecessary CONFIG_IS_ENABLED() Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-10kconfig / kbuild: Re-sync with Linux 4.19Tom Rini
Align Kconfig and Kbuild logic to Linux 4.19 release with minimal impact on files outside of this scope. Our previous Kconfig sync was done by commit 5972ff077e0f ("kconfig / kbuild: re-sync with Linux 4.18"). In this particular re-sync in order to keep clang support working a number of related changes needed to be pulled in that had been missed previously. Not all of these changes we easily traceable and so have been omitted from the list below. The imported Linux commits are: [From prior to v4.18] 9f3f1fd29976 kbuild: Add __cc-option macro d7f14c66c273 kbuild: Enable Large File Support for hostprogs 6d79a7b424a5 kbuild: suppress warnings from 'getconf LFS_*' 24403874316a Shared library support 86a9df597cdd kbuild: fix linker feature test macros when cross compiling with Clang 0294e6f4a000 kbuild: simplify ld-option implementation [From v4.18 to v4.19] 96f14fe738b6 kbuild: Rename HOSTCFLAGS to KBUILD_HOSTCFLAGS 10844aebf448 kbuild: Rename HOSTCXXFLAGS to KBUILD_HOSTCXXFLAGS b90a368000ab kbuild: Rename HOSTLDFLAGS to KBUILD_HOSTLDFLAGS 8377bd2b9ee1 kbuild: Rename HOST_LOADLIBES to KBUILD_HOSTLDLIBS f92d19e0ef9b kbuild: Use HOST*FLAGS options from the command line 4ab3b80159d4 kconfig: check for pkg-config on make {menu,n,g,x}config 693359f7ac90 kconfig: rename SYMBOL_AUTO to SYMBOL_NO_WRITE f60b992e30ff kbuild: replace $(LDFLAGS) $(ldflags-y) with $(ld_flags) 2fb9279f2c3e kbuild: change ld_flags to contain LDFLAGS_$(@F) c931d34ea085 arm64: build with baremetal linker target instead of Linux when available 5accd7f3360e kconfig: handle format string before calling conf_message_callback() a2ff4040151a kconfig: rename file_write_dep and move it to confdata.c 0608182ad542 kconfig: split out useful helpers in confdata.c adc18acf42a1 kconfig: remove unneeded directory generation from local*config 79123b1389cc kconfig: create directories needed for syncconfig by itself 16952b77d8b5 kconfig: make syncconfig update .config regardless of sym_change_count d6c6ab93e17f kbuild: remove deprecated host-progs variable 56869d45e364 kconfig: fix the rule of mainmenu_stmt symbol c151272d1687 kconfig: remove unused sym_get_env_prop() function 1880861226c1 kconfig: remove P_ENV property type e3fd9b5384f3 scripts/dtc: consolidate include path options in Makefile 4bf6a9af0e91 kconfig: add build-only configurator targets f1575595d156 kconfig: error out when seeing recursive dependency 5e8c5299d315 kconfig: report recursive dependency involving 'imply' f498926c47aa kconfig: improve the recursive dependency report 98a4afbfafd2 kconfig: fix "Can't open ..." in parallel build 9a9ddcf47831 kconfig: suppress "configuration written to .config" for syncconfig 87a32e624037 kbuild: pass LDFLAGS to recordmcount.pl d503ac531a52 kbuild: rename LDFLAGS to KBUILD_LDFLAGS 217c3e019675 disable stringop truncation warnings for now bc8d2e20a3eb kconfig: remove a spurious self-assignment fd65465b7016 kconfig: do not require pkg-config on make {menu,n}config 5a4630aadb9a ftrace: Build with CPPFLAGS to get -Qunused-arguments Note that this adds new cleanup work to do in that we should adapt the shared library support we have to what is now upstream. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
2020-03-31Merge branch 'next' of git://git.denx.de/u-boot-usb into nextTom Rini
2020-03-17riscv: Implement new SBI v0.2 extensionsBin Meng
Few v0.1 SBI calls are being replaced by new SBI calls that follows v0.2 calling convention. Implement the replacement extensions and few additional new SBI function calls that makes way for a better SBI interface in future. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-03-17riscv: Introduce a new config for SBI v0.1Bin Meng
We now have SBI v0.2 which is more scalable and extendable to handle future needs for RISC-V supervisor interfaces. Introduce a new config and move all SBI v0.1 code under that config. This allows to implement the new replacement SBI extensions cleanly and remove v0.1 extensions easily in future. Currently, the config is enabled by default. Once all M-mode software, with v0.1, is no longer in use, this config option and all relevant code can be easily removed. This commit is inspired from Linux kernel patch: https://patchwork.kernel.org/patch/11407361/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-03-17riscv: Add SBI v0.2 extension definitionsBin Meng
Few v0.1 SBI calls are being replaced by new SBI calls that follows v0.2 calling convention. This patch just defines these new extensions. This commit is inspired from Linux kernel patch: https://patchwork.kernel.org/patch/11407359/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-03-17riscv: Add basic support for SBI v0.2Bin Meng
The SBI v0.2 introduces a base extension which is backward compatible with v0.1. Implement all helper functions and minimum required SBI calls from v0.2 for now. All other base extension function will be added later as per need. As v0.2 calling convention is backward compatible with v0.1, remove the v0.1 helper functions and just use v0.2 calling convention. Add a new Kconfig options CONFIG_SBI for the new SBI v0.2 codes, and let CONFIG_SBI_IPI depend on it. This commit is inspired from Linux kernel patch: https://patchwork.kernel.org/patch/11407363/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-03-17riscv: Mark existing SBI as v0.1 SBIBin Meng
As per the new SBI specification, current SBI implementation version is defined as 0.1 and will be removed/replaced in future. Each of the function call in 0.1 is defined as a separate extension which makes easier to replace them one at a time. Rename existing implementation to reflect that. This patch is just a preparatory patch for SBI v0.2 and doesn't introduce any functional changes. This commit is inspired from Linux kernel patch: https://patchwork.kernel.org/patch/11407355/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-03-17riscv: Avoid calling sbi_clear_ipi()Bin Meng
There is no need for S-mode U-Boot to call sbi_clear_ipi() as it can be cleared directly from S-mode. This saves some cycles. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas@auer.io>
2020-03-17riscv: Fix sbi_remote_sfence_vma{,_asid}Bin Meng
Currently sbi_remote_sfence_vma{,_asid} does not pass their arguments to SBI at all, which is semantically incorrect. This keeps in sync with Linux kernel commit: a21344dfc6ad: fix sbi_remote_sfence_vma{,_asid} Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas@auer.io>
generated by cgit (git 2.34.1) at 2025-02-04 16:45:29 +0000