| Age | Commit message (Collapse) | Author |
|---|
|
While it is true that we no longer have 'ppcenv' and similar sections,
including env/embedded.o at all results in the text/etc sections being
available for the rest of the link. This in turn is required for the
setup used on ms7722se. This also, likely, needs further fine-tuning.
Fixes: f40ad66fa066 ("arch/sh: don't bring common/env_embedded.o into the link")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The linker script for SuperH brings the .ppcenv and .ppcenvr section
of common/env_embedded.o into the .text section. However, the .ppcenv
section is only ever filled in by env_embedded.o when
CONFIG_SYS_USE_PPCENV is defined, but no platforms in mainline U-Boot
use this.
In addition, common/env_embedded.o is not always built (when you use
CONFIG_ENV_IS_NOWHERE for example), which causes the following build
failure:
Fixes:
LD u-boot
/home/thomas/sh4aeb-linux-musl/bin/sh4aeb-linux-ld.bfd: cannot find common/env_embedded.o
We fix this by no longer adding the .ppcenv and .ppcenvr sections from
common/env_embedded.o into the .text section.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The SuperH architecture allows to be run in either little or big
endian mode. Some SuperH SoCs get the little vs. big endian decision
through mode pins sampled at reset, so if big endian has been choosen
by HW designers, it cannot be easily changed.
Therefore, it makes sense to allow building U-Boot for SuperH in big
endian mode. To allow this, the only change needed is to adjust the
OUTPUT_FORMAT() in the linker script.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Finally add fpic compilation option to produce relocatable code.
Note that this requires to define CONFIG_NEEDS_MANUAL_RELOC for all
board files, also relocation support still has some limitations
(e.g. a developer should care not to overwrite the executing code or
memset() with zeroes not yet relocated data on malloc init etc.),
which may be fixed while switching to PIE.
Due to short investigation the architecture code is not ready for PIE
linking, this will require some manipulations with .dyn* sections.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
It is easy to note that SH2/SH3/SH4 start.S code is practically
the same with a minor difference for SH2 where a short data header is
present. To avoid unwanted code duplication and to automatically
convert SH2 and SH3 platforms to generic board support move fixed SH4
start.S into arch/sh/lib/start.S and share it among all platforms.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Like on ARM platform keep the first code relocation from a U-boot
image storage to RAM at CONFIG_SYS_TEXT_BASE, then pass execution to a
generic board_init_f() with empty GD flags. If CONFIG_SYS_TEXT_BASE is
equal to a calculated by board_init_f() relocation address there will
be no more code and data copy, however it's worth to mention that the
first copy happens even if $pc on _start is the same as
CONFIG_SYS_TEXT_BASE, on practice this works without a problem.
Also note that _sh_start is renamed back to _start to correct
gd->mon_len calculation by setup_mon_len(), the opposite rename was
done in pre-generic board commit 2024b968ee9 ("sh: Fix build in start.S").
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Commits b61e90e6fd83 ("sh: Drop the arch-specific board init") and
f41e6088eb1a ("sh: Fix build errors for generic board") left code and
data relocation done in start.S, however further actual U-boot
configuration is not started anymore. Practically SH boards with the
code relocated into the expected position by start.S still can be
booted, so the change adds this option and provides an option how to
relocate code for board_init_r() execution.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At the moment in runtime all defined sections are copied into or
created in RAM, specify this explicitly to assert potential out of RAM
placements of the sections.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
No functional change, concentrate linker script commands in one
place for convenience. Entry point is set to CONFIG_SYS_TEXT_BASE by
default on build, so this option can be omitted from being added to
the linker script.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Reference lowlevel_init of all supported SH2A/SH3/SH4/SH4A boards
from a shared linker script, the lowlevel_init function will be called
by a relative address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Three supported SH4/SH4A boards with the bootloader image stored on
SPI flash have own flavour of a linker script, in turn they are equal
among each other. The only difference is that the text from
lowlevel_init.o is placed right after start.o, which makes sense.
Note that .bss section is not marked as NOLOAD, because for about
10 years this is a default option of a GNU linker, either the
attribute is found or not the resulting image file is the same.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
No functional change, moving cache manipulation functions into cache.c
allows to collect all of them in a single location and as a pleasant
side effect cache_control() function can be unexported now.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
cache_wback_all() is a local function and it is called from
cache_control() only, which is in turn jumps to P2 area.
The change fixes an issue when cache_wback_all() returns from P2 to
P1, however cache_control() continues to manipulate with CCR
register, according to the User's Manual this is restricted.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Both jump_to_P2() and back_to_P1() functions are found in asm/system.h
header file and functionally they are the same, don't redefine them.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The change is similar to commit 994b56616bae ("sh: delete an unused
source file") for SH2, however here the removed cache.c file was
built and included into an image as a dead code.
If it is needed in future the contents can be reused from a similar
arch/sh/cpu/sh4/cache.c file, which is in turn will be moved to
a shared among all core flavours location at arch/sh/lib/cache.c.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, instead of doing cache invalidation only with
the wrapped 'ocbi' instruction pin flush_cache() to cache invalidation
with memory write-back done by 'ocbp'.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, thus in flush_dcache_range() implementation
change SH4 cache write-back only instruction 'ocbwb' with cache purge
instruction 'ocbp', according to the User's Manual there should be no
performance penalty for that.
Note that under circumstances only cache invalidation is expected from
flush_cache() call, in these occasional cases the current version of
flush_cache() works, which is a wrapper over invalidate_dcache_range()
at the moment, this will be fixed in the following change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
This includes the following fixes:
- Define needed __init_end symbol - see initr_reloc_global_data()
- Drop SH-specific struct bd_info
- Add an empty relocate_code() function
This prevents build errors with generic board, but the code will still need
work. Perhaps this is a better alternative than deleting the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
|
|
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4
to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A,
CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because
arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The linker scripts of sh2/sh3/sh4 are almost the same.
The difference among them is essentially only one line.
They can be consolidated into a single file, arch/sh/cpu/u-boot.lds
by re-writing the diffrent line as follows:
KEEP(*/start.o (.text))
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
-ffixed-r13 is defined commonly for sh2, sh3, sh4.
Move it to arch/sh/config.mk
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
-ffreestanding is defined at the top Makefile for all architectures.
Do not define it twice for SH2A.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
SH4 and SH4A are compatible. But some instructions are different from these.
In Linux kernel, It is treated as a separate CPU, but for now, I think that
there is no need to divide especially in the U-Boot.
This removes CONFIG_SH4A definition from source code, SH4A is treated as SH4.
And this fix white space.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
A chache API of SH is developped by reference in linux kernel.
And API was the same as the linux kernel.
This patch change cache API to defines as U-Boot.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
|
|
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
|
|
Even if using CPU is SH-4A, the previous code always put "SH4".
This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Recent builds for SH4 boards fail with a lot of errors like:
cmd_mem.o: In function 'dcache_invalid_range':
include/asm/cache.h:25: multiple definition of 'dcache_invalid_range'
include/asm/cache.h:25: first defined here
This is due to the funcs being defined in the header, but not static
or inline or extern. So move them to the sh4-specific cache.c file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Not all SuperH toolchains support -mno-fdpic. Chances are good that if
the flag doesn't work, it isn't defaulting to the FDPIC ABI, so the flag
isn't needed. So only add it if it is actually supported.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Only the optimization of sh2 had been supported up.
This adds the optimization of sh2a.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
|
|
The start.o section is changed by --gc-section option of ld.
Of this using KEEP order, therefore, evade this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Linker needs to use the proper endian/bfd flags even when doing partial linking.
LDFLAGS_u-boot sets linker option which is called it when U-boot is built
(u-boot final).
LDFLAGS sets necessary option by partial linking (use in cmd_link_o_target).
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
By commit 6d8962e814c15807dd6ac5757904be2a02d187b8,
label of _start was not usable in start.S and build fail.
This change label from _start to _sh_start.
----
arch/sh/cpu/sh4/libsh4.o: In function `_start':
(.text+0x204): multiple definition of `_start'
arch/sh/cpu/sh4/start.o:(.text+0x0): first defined here
----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
|
|
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
|
