| Age | Commit message (Collapse) | Author |
|---|
|
Quark SoC does not support MSR MTRRs. Fixed and variable range MTRRs
are accessed indirectly via the message port and not the traditional
MSR mechanism. Only UC, WT and WB cache types are supported.
We configure all the fixed range MTRRs with common values (VGA RAM
as UC, others as WB) and 3 variable range MTRRs for ROM/eSRAM/RAM as
WB, which significantly improves the boot time performance.
With this commit, it takes only 2 seconds for U-Boot to boot to shell
on Intel Galileo board. Previously it took about 6 seconds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Thermal sensor on Quark SoC needs to be properly initialized per
Quark firmware writer guide, otherwise when booting Linux kernel,
it triggers system shutdown because of wrong temperature in the
thermal sensor is detected by the kernel driver (see below):
[ 5.119819] thermal_sys: Critical temperature reached(206 C),shutting down
[ 5.128997] Failed to start orderly shutdown: forcing the issue
[ 5.135495] Emergency Sync complete
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
When Linux kernel boots, it hangs at:
[ 0.829408] Intel Quark side-band driver registered
This happens when Quark kernel Isolated Memory Region (IMR) driver
tries to lock an IMR register to protect kernel's text and rodata
sections. However in order to have IMR function correctly, HMBOUND
register must be locked otherwise the system just hangs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
On Intel Quark, lots of registers on the message port need be
programmed. Add handy clrbits, setbits, clrsetbits macros for
message port access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.
Enable PCIe controller per Quark firmware writer guide.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.
To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add the main routines for Quark Memory Reference Code (MRC).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
device.h for integrated pci devices' bdf on Quark SoC and quark.h for
various memory-mapped and i/o-mapped base addresses within SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
