| Age | Commit message (Collapse) | Author |
|---|
|
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
According to De Morgan's Law[1]:
!(A && B) = !A || !B
!(A || B) = !A && !B
There are 5 places in the code where we find:
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
and 4 places in the code where we find:
#if (!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF))
In words, the construct:
!defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE on?"
and the construct:
defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE off?"
Therefore
!(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
means:
"the opposite of 'are they both off?'"
in other words:
"are either or both on?"
and:
(!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF)
means:
"are either or both on?"
As a result, I've converted the 4 instances of '(!A || !B)' to '!(A && B)' for
consistency.
[1] https://en.wikipedia.org/wiki/De_Morgan%27s_laws
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
|
|
- SoCFPGA DT and reset cleanup, AE MCVEVK board support.
|
|
STM32 MCUs update:
_ Add MPU region for SPI NOR memory mapped region
_ Add missing QSPI flash compatible for STM32 F7 boards
_ Update spi-tx-bus-width and spi-rx-bus-width properties
_ Add QSPI support for STM32F469 Discovery board
|
|
Keep the FPGA bridge entries in SPL DT to let do_bridge_reset() toggle
the bridges on/off as needed according to the handoff file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Pull out the u-boot,dm-pre-reloc from socfpga_arria10_socdk_sdmmc_handoff.dtsi
into separate dtsi header file to make it easier to patch in custom handoff
dtsi files, without having to manually add the U-Boot bits. Shuffle the include
clauses in the A10 DT files to make it obvious what gets included where without
having to follow confusing long chain of includes, i.e. board DT file includes
everything it needs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d568
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
The stratix 10 reset manager ad-hoc code in arch/arm contains an unused
function 'reset_deassert_peripherals_handoff' that has been added from
the beginning. As this is probably a result of copying the gen5 reset
manager and this function has never been used, remove it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
commit c5de2b7eae68 ("arm: socfpga: implement proper peripheral reset")
has removed the call to 'reset_deassert_peripherals_handoff()' from
socfpga gen5 SPL since the reset driver now handles resets. However,
commit c1d4b464c8b8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA")
has re-added this ad-hoc reset code, so that all peripherals were now
again enabled instead of letting the drivers enable them by request.
While at it, remove this function for gen5 as it should not be used.
Fixes: commit c1d4b464c8b8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
- A10 FPGA programming support, Gen5 livetree conversion
|
|
Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Mark Jonas <mark.jonas@de.bosch.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
|
|
Instead of overlading makefile, use the k3_gen_x509_cert.sh script
to generate boot images.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
For chainboot configurations or test environments, this patch allows
booting barebox images by using command bootz.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
|
|
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
|
|
- DM updates for multiple MVEBU boards (Stefan)
- Add CRS305-1G-4S board (Luka)
- Enable MMC in SPL on clearfog (Baruch)
|
|
- Correct SYS_TEXT_BASE for qemu.
- Support booti.
- Increase SYSBOOTM_LEN for Fedora/RISCV kernel.
- Support SMP booting from flash.
|
|
- Add USB PHY drivers for Amlogic G12A
- Add USB Complex Glue driver for Amlogic G12A
- Add USB Gadget support for Amlogic G12A
|
|
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add initial support for Nanopi M4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- eMMC socket
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI
- USB 3.0 x4
- USB Type C power and data
- GPIO1, GPIO2 expansion ports
- DC5V/3A
Commit details of rk3399-nanopi-m4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Refine nanopi4 differences"
(sha1: c62ffaf5026d0b7633e62b2cea8450b5543c349a)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Attaching GPIO functionality to SDMMC0_DET pin (which
does in Linux base dts) make dwmmc driver "fail to detect
the card".
Card did not respond to voltage select!
It may be because the existing driver can't support gpio
card detection. So, change the pinctrl functionality from
RK_FUNC_GPIO to RK_FUNC_1 like other rk3399 dts does via
sdmmc_cd pin.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
https://patchwork.kernel.org/patch/10925543/
Tested on HiFive Unleashed and QEMU.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Karsten Merker <merker@debian.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
|
enabled
This patch will fix prior_stage_fdt_address write failure problem, when
AE350 boots from flash.
When AE350 boots from flash, prior_stage_fdt_address will be flash
address, we shall avoid it to be written.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
When U-Boot boots from flash, during the boot process,
hart_lottery and available_harts_lock variable addresses
point to flash which is not writable. This causes boot
failures on AE350. Introduce a config option CONFIG_XIP
to support such configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Adds support for Amlogic G12A USB Device mode.
The DWC2 Controller behind the Glue can be connected to an OTG
capable PHY. The Glue setups the PHY mode.
This patch implements Device mode support by adding a board_usb_init/cleanup
setting up the DWC2 controller and switch the OTG capable port to Device
before starting the DWC2 controller in Device mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
- Various PHY fixes / enhancements.
- TI K2G fixes
|
|
Commit ff7bd212cb8a ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702b1 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
- H6 Beelink GS1 board (Clément)
- Olimex A64-Teres-I board (Jonas)
- sunxi build fix for CONFIG_CMD_PXE|DHCP (Ondrej)
- Change include order (Jagan)
- EPHY clock changes (Jagan)
- EMAC enablement on Cubietruck Plus, BPI-M3 (Chen-Yu Tsai)
|
|
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Sync rk3399-nanopi4.dtsi from Linux 5.1-rc2 tag.
Linux commit details about the rk3399-nanopi4.dtsi sync:
"arm64: dts: rockchip: Add nanopi4 bluetooth"
(sha1: 3e2f0bb72be36aa6c14ee7f11ac4dd8014801030)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Few SPL and U-Boot proper configs are common to all rk3399 target
defconfigs, move them and select it from platform kconfig.
Moved configs:
- SPL_ATF
- SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
- SPL_LOAD_FIT
- SPL_CLK if SPL
- SPL_PINCTRL if SPL
- SPL_RAM if SPL
- SPL_REGMAP if SPL
- SPL_SYSCON if SPL
- CLK
- FIT
- PINCTRL
- RAM
- REGMAP
- SYSCON
- DM_PMIC
- DM_REGULATOR_FIXED
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
To make successful build with dts(i) files syncing from Linux 5.1-rc2
the rk3399.dtsi would require pwm2_pin_pull_down.
So, sync the pwm2_pin_pull_down node from Linux 5.1-rc2. Since this
node is strictly not part of any commit alone, I have mentioned
Linux 5.1-rc2 tag for future reference of where would this sync
coming from.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Now we have
- board specific -u-boot.dtsi files for board specific u-boot
dts changes.
- soc specific rk3399-u-boot.dtsi for soc specific u-boot
dts changes.
So, include the rk3399-u-boot-dtsi on respective board -u-boot.dtsi
and drop the properties which are globally available in rk3399-u-boot.dtsi
Right now rk3399-u-boot.dtsi has sdmmc, spi1 u-boot,dm-pre-reloc
property and more properties and nodes can be move further based
on the requirements.
This would fix, the -u-boot.dtsi inclusion for evb, firefly, puma
boards that was accidentally merged on below commit.
"rockchip: dts: rk3399: Create initial rk3399-u-boot.dtsi"
(sha1: e05b4a4fa84b65a0c8873e8f34721741fe2bc09d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add u-boot,dm-pre-reloc property for spi1, so-that the
subsequent rk3399 boards which boot from SPI.
This help to separate the u-boot specific properties away
from base dts files so-that the Linux sync become easy and
meaningful.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Devicetree files in RK3399 platform is synced from Linux, like other
platforms does. Apart from these u-boot in rk3399 would also require
some u-boot specific node like dmc.
dmc node has big chunk of DDR timing parameters which are specific
to specific board, and maintained with rk3399-sdram*.dtsi.
So, create board specific -u-boot.dtsi files and move these sdram dtsi
files accordingly. This would help of maintain u-boot specific changes
separately without touching Linux dts(i) files which indeed easy for
syncing from Linux between releases.
These board specific -u-boot.dtsi can be extendible to add more u-boot
specific nodes or properties in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
- Sometimes u-boot specific dtsi files are included
automatically which would build for entire rockchip SoC,
even-though the respective dtsi should used it for specific
family of rockchip SoC.
- Sometimes u-boot specific dts nodes or properties can use
config macros from respective rockchip family include/configs
files, example CONFIG_SPL_PAD_TO.
So, it's better to compile the dtbs based on the respective
rockchip family types rather than rockchip itself to avoid
compilation issues.
This patch organize the existing dtb's based on the rockchip
family types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Enable sound for this board, which has the same codec as jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Rockchip platform suppose to use TPL(run in SRAM) as dram init and
SPL(run in DDR SDRAM) as pre-loader, so that the SPL would not be
limited by SRAM size.
This patch add rk3399-board-tpl.c and its common configs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
