summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2015-02-17ARM: i.MX: provide access to reset cause through get_imx_reset_cause()Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2015-02-17ARM: imx6 Add WDOG3 for i.MX6SXPeng Fan
There are three wdogs for i.MX 6SoloX. Add wdog3 support in function imx_set_wdog_powerdown. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-17ARM: imx6: disable bandgap self-bias after bootPeng Fan
The self-bias circuit is used by the bandgap during startup. Once the bandgap has stabilized, the self-bias circuit should be disabled for best noise performance of analog blocks. Also this bit should be disabled before the chip enters STOP mode or when ever the regular bandgap is disabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
2015-02-10Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini
2015-02-10Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2015-02-10Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-02-10arm: mxs: Add 'Wait for JTAG user' if booted in JTAG modeGraeme Russ
When booting in JTAG mode, there is no way to use soft break-points, and no way of knowing when SPL has finished executing (so the user can issue a 'halt' command to load u-boot.bin for example) Add a debug output and simple loop to stop execution at the completion of the SPL initialisation as a pseudo break-point when booting in JTAG mode Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10arm: mxs: Enable booting of mx28 without batteryGraeme Russ
Section 4.1.2 of Freescale Application Note AN4199 describes the configuration required to operate the mx28 from a 5V source without a battery. This patch changes the behaviour of the dropout control of the DC-DC converter (refer to section 11.12.9 of the mx28 Application Processor Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the following: - Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined - Switch between 4P2 Linear Regulator and Battery, using whichever has the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is the same as the pre-patch behaviour) Signed-off-by: Graeme Russ <gruss@tss-engineering.com> Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
2015-02-10arm: mxs: Add debug outputs and comments to mxs SPL source filesGraeme Russ
It is difficult to track down fail to boot issues in the mxs SPL. Implement the following to make it easier: - Add debug outputs to allow tracing of SPL progress in order to track where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must be defined to enable debug output in SPL - Add TODO comments where it is not clear if the code is doing what it is meant to be doing, even tough the board boots properly (these comments refer to existing code, not to any code added by this patch) Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10imx: mx6: Fixed AIPS3 base address issueYe.Li
Should use AIPS3 configuration address 0x0227C000 to set AIPS3, not the AIPS3 base address. Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem. Signed-off-by: Ye.Li <B37916@freescale.com>
2015-02-10imx:mx6 update fuse_bank0_regsPeng Fan
Update fuse_bank0_regs structure according reference mannual. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-09Merge branch 'microblaze' of git://git.denx.de/u-boot-microblazeTom Rini
2015-02-09Merge git://git.denx.de/u-boot-arcTom Rini
2015-02-09microblaze: spl: Add LISTS to linker scriptMichal Simek
This is required for driver model. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: spl: Do not call mem_malloc_init and use early allocMichal Simek
This patch has some parts connected together: - Use _gd in bss section which is automatically cleared Location at SPL_MALLOC_END wasn't cleared at all - Use MALLOC_F_LEN(early alloc) instead of FULL MALLOC (mem_malloc_init is not called at all) - Simplify malloc and stack init. At the end of SPL addr is malloc area and below is stack Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Add support for CONFIG_SYS_MALLOC_F_LENMichal Simek
Create space for dm_init where calloc is called and malloc_base has to be initialized. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Do not use CONFIG_SYS_GENERIC_GLOBAL_DATAMichal Simek
Because it is not compatible with DM where malloc_base has to be available early and init has to be done in ASM. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Speedup code copyMichal Simek
Remove one instruction in the loop which speedup code copying. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Move architecture to use generic board initMichal Simek
Compile code with -fPIC to get GOT. Do not build SPL with fPIC because it increasing SPL size for nothing. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Fix gd_t address which is placed at the end of BRAMMichal Simek
Setup gd from ASM to be availalbe for board_init_r. Setting it up in spl_board_init is too late when MALLOC is used. Space for gd is located behind MALLOC area at the end of BRAM. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Remove unused asm labelMichal Simek
It is not used at all that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Use standard interrupt_init() functionMichal Simek
Do not use microblaze specific interrupt init function. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Remove unneeded data section adding from DTBMichal Simek
DTB is added to rodata section: [ 2] .rodata PROGBITS 84c5b60c 05c60c 00c618 00 A 0 0 4 [ 3] .dtb.init.rodata PROGBITS 84c67c30 068c30 003c80 00 A 0 0 16 [ 4] .rela.dyn RELA 84c6b8b0 06c8b0 000534 0c A 0 0 4 [ 5] .data PROGBITS 84c6bde4 06cde4 001536 00 WA 0 0 16 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Add debug message about enabling interruptsMichal Simek
Add one more debug message about enabling global interrupts. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Fix coding styleMichal Simek
No functional changes just to pass checkpatch.pl. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Remove DEBUG_INT macro and use debug() insteadMichal Simek
Do not use specific macros for debugging. Also remove compilation warning: w+../arch/microblaze/cpu/interrupts.c: In function 'interrupt_handler': w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'void (*)(void *)' [-Wformat] w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'void *' [-Wformat] Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Fix coding style in exception.cMichal Simek
Just coding style cleanup - no functional changes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Show return address from exceptionMichal Simek
Show also return address from exception which should suggest where the problem is. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09microblaze: Fix stack usage in interrupt handlerMichal Simek
Do not save registers below r1 stack pointer because it is not checked by stack undeflow is not able to detect it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-02-09common: Move dram_init() declaration to common locationMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-09arc: build libgcc in U-BootAlexey Brodkin
This way we may have very limited set of functions implemented so we save some space. Also it allows us to build U-Boot for any ARC core with the same one toolchain because we don't rely on pre-built libgcc. For example: * we may use little-endian toolchain but build U-Boot for ether endianess * we may use non-multilibbed uClibc toolchain but build U-Boot for whatever ARC CPU flavour that current GCC supports Private libgcc built from generic C implementation contributes only 144 bytes to .text section so we don't see significant degradation of size: --->8--- $ arc-linux-size u-boot.libgcc-prebuilt text data bss dec hex filename 222217 24912 214820 461949 70c7d u-boot.libgcc-prebuilt $ arc-linux-size u-boot.libgcc-private text data bss dec hex filename 222361 24912 214820 462093 70d0d u-boot.libgcc-private --->8--- Also I don't notice visible performance degradation compared to pre-built libgcc (where at least "*div*" functions are had-written in assembly) on typical operations of downloading 10Mb uImage over TFTP and bootm. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: move CPU flags selection to the main "config.mk"Alexey Brodkin
As a preparation to ARCv2 port submission we're moving CPU slection flags to a common location. Also it will allow us to have more flexible CPU specification, not only ISA version but CPU family as well checking CONFIG_ARC_CPU_xxx. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: hard-code CONFIG_ARCH_EARLY_INIT_R in asm/config.hAlexey Brodkin
Common arch_early_init_r() is used in "arc/lib/cpu.c" for all ARC boards so there's no sense in separate per-board definitions. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: hard-code CONFIG_SYS_GENERIC_BOARD into asm/config.hAlexey Brodkin
There're no other options for ARC except "generic board" so ther's no point to define CONFIG_SYS_GENERIC_BOARD per board. We now have it set fo all ARC boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: add selection of endianess in KconfigAlexey Brodkin
This change allows to keep board description clean and minimalistic. This is especially helpful if one board may house different CPUs with different features. It is applicable to both FPGA-based boards or those that have CPUs mounted on interchnagable daughter-boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: select cache settings via menuconfigAlexey Brodkin
This change allows to keep board description clean and minimalistic. This is especially helpful if one board may house different CPUs with different features. It is applicable to both FPGA-based boards or those that have CPUs mounted on interchnagable daughter-boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: define and use PTAG AUX regs for MMUv3 onlyAlexey Brodkin
DC_PTAG and IC_PTAG registers only exist in MMUv3. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: add more flavours of ARC700 series CPUAlexey Brodkin
Now we may select a particular version of ARC700: * ARC750D or * ARC770D It allows more flexible (or more fine tuned) configuration of U-Boot. Before that change we relied on minimal configuration but now we may use specific features of each CPU. Moreover allows us to escape manual selection of options that exist in both CPUs but may have say different version like MMUv2 in ARC750D vs MMUv3 in ARC770D. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-02-09arc: memcmp - fix zero-delay loop utilizationIgor Guryanov
It's prohibited to put branch instruction in the very end of zero-delay loop. On execution this causes "Illegal instruction" exception. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
2015-02-07arm, at91: add reset controller status registerHeiko Schocher
add reset controller status register Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Bo Shen <voice.shen@atmel.com>
2015-02-07arm, at91, wdt: do not disable WDT in SPLHeiko Schocher
if CONFIG_AT91SAM9_WATCHDOG is set, do not disable WDT in SPL Signed-off-by: Heiko Schocher <hs@denx.de>
2015-02-07ARM: atmel: cleanup: remove at91cap9 related codeBo Shen
As the at91cap9adk board is removed by commit: b5508344 (ARM: remove broken "at91cap9adk" board), so the at91cap9 code is not used anymore, and also the document for at91cap9 can not be found on www.atmel.com, so remove the at91cap9 related code. Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07ARM: atmel: sama5d4_xplained: enable spl supportBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: sama5d4ek: enable SPL supportBo Shen
The sama5d4ek support boot up from NAND flash, SD/MMC card and also the SPI flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: sama5d4: build related file when enable SPLBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: sama5d4: can access DDR in interleave modeBo Shen
The SAMAA5D4 SoC can access DDR in interleave mode. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: sama5d4: add interrupt redirect functionBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix subject] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07ARM: atmel: sama5d4: add bus matrix init functionBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: sama5d4: add matrix1 base addr definitionBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07ARM: atmel: spl: can not disable osc for sama5d4Bo Shen
The SAMA5D4 SoC on chip rc oscillator can not be disabled. Signed-off-by: Bo Shen <voice.shen@atmel.com>
generated by cgit (git 2.34.1) at 2025-01-06 23:21:49 +0000