| Age | Commit message (Collapse) | Author |
|---|
|
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a new sun6i machine that supports UART and MMC.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef
around mmc and smp code, drop MACH_TYPE]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: commit message was "ARM: sunxi: Setup the A31 UART0 muxing"]
[wens@csie.org: reorder #ifs by SUN?I]
[wens@csie.org: replace magic numbers with GPIO definitions]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
UART0 is the default debug/console UART on the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This patch adds the basic clocks support for the Allwinner A31 (sun6i)
processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
This includes changes from the following commits from u-boot-sunxi:
a92051b ARM: sunxi: Add sun6i clock controller structure
1f72c6f ARM: sun6i: Setup the UART0 clocks
5f2e712 ARM: sunxi: Enable pll6 by default on all models
2be2f2a ARM: sunxi-mmc: Add mmc support for sun6i / A31
12e1633 ARM: sun6i: Add initial clock setup for SPL
1a9c9c6 ARM: sunxi: Split clock code into common, sun4i and sun6i code
0b194ee ARM: sun6i: Properly setup the PLL LDO in clock_init_safe
b54c626 sunxi: avoid sr32 for APB1 clock setup.
68fe29c sunxi: remove magic numbers from clock_get_pll{5,6}
c89867d sunxi: clocks: clock_get_pll5 prototype and coding style
501ab1e ARM: sunxi: Fix sun6i PLL6 settings
37f669b ARM: sunxi: Fix macro names for mmc and uart reset offsets
61de1e6 ARM: sunxi: Correct comment for MBUS1 register in sun6i clock definitions
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: styling fixes reported by checkpatch.pl]
[wens@csie.org: drop unsupported SPL code block and unused gpio.h header]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The A31 has a new module called PRCM, or Power, Reset Control Module.
This module controls clocks and resets for RTC block modules, and also
PLL biasing in the main clock module.
This patch adds the register definitions, and also enables the clocks
and resets for the RTC block PIO (pin controller) and P2WI (push-pull
2 wire interface) which is used to talk to the PMIC.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: spacing fixes reported by checkpatch.pl]
[wens@csie.org: Use setbits helper in PRCM init function]
[wens@csie.org: rephrase commit message to explain what the hardware
supports and what we actually enable]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
A31 has several new and changed memory address. This patch adds them.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
We have already defined macros for pull-up/down values in the
GPIO header. Use them instead of magic numbers when configuring
the UART pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This commit converts UniPhier on-chip serial driver to driver model.
Since UniPhier SoCs do not have Device Tree support, some board files
should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories.
(Device Tree support for UniPhier platform is still under way.)
Now the base address and master clock frequency are passed from
platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and
CONFIG_SYS_UNIPHIER_UART_CLK should be removed.
Tested on UniPhier PH1-LD4 ref board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This makes use of the existing device tree node to use driver model
for the serial console.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add more information so that U-Boot can find the address of the serial port.
Also fix the reg-shift value.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This code doesn't follow the normal approach of having its arch-specific
definitions in an arch-specific directory. Add a new arch-specific file
and make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for this by reserving a block of memory below global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
To permit information to be passed from the early U-Boot code to
board_init_f() we cannot zero the global_data in board_init_f(). Instead
zero it in the start-up code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This code generates warnings with recent gcc versions. We really don't need
the clobber specification, so just drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These ended up in arch/arm/dts/dt-bindings temporarily, but in fact the
correct place is now include/dt-bindings. Move them to be consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
|
|
Provide suitable platform data for am33xx boards, so that these boards can
use driver model for serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Provide suitable platform data for am33xx boards, so that these boards can
use driver model for GPIO access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.
Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Select serial0 as the console.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
|
|
|
|
Without the private libgcc, we need a full multilib toolchain with
different libgcc or multiple toolchains to build all BE/LE and
hard-float/soft-float variants of MIPS boards. That is not feasible.
This commit allows us to build all the MIPS boards with a single
kernel.org toolchain:
https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/
x86_64-gcc-4.9.0-nolibc_mips-linux.tar.xz
This change sounds reasonable for most users. If necessary,
you can disable this option via "make menuconfig" or friends.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
|
|
The motivation of this commit is to change CONFIG_USE_PRIVATE_LIBGCC
to a boolean macro so we can move it to Kconfig.
In the current implementation, there are two forms of syntax
for this macro:
- CONFIG_USE_PRIVATE_LIBGCC=y
- CONFIG_USE_PRIVATE_LIBGCC=path/to/private/libgcc
The latter is only used by x86 architecture.
With a little bit refactoring, it can be converted to the former.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Fix the following checkpatch issues:
CHECK: No space is necessary after a cast
\#39: FILE: arch/arm/include/asm/arch-am33xx/mux.h:39:
+#define PAD_CTRL_BASE 0x800
+#define OFFSET(x) (unsigned int) (&((struct pad_signals *) \
CHECK: Avoid CamelCase: <CONTROL_PADCONF_JTAG_nTRST>
\#284: FILE: arch/arm/include/asm/arch-omap3/mux.h:284:
+#define CONTROL_PADCONF_JTAG_nTRST 0x0A1C
ERROR: space required after that ',' (ctx:VxV)
\#446: FILE: arch/arm/include/asm/arch-omap3/mux.h:446:
+#define MUX_VAL(OFFSET,VALUE)\
^
Cc: Raphael Assenat <raph@8d.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
|
|
The cm-t35 board support covers both cm-t3530 and cm-t3730 boards.
Mention both boards in the Kconfig option prompt.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Add ddr3 commands:
test <start_addr in hex> <end_addr in hex> - test DDR from start\n
address to end address\n
ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n
compare DDR data of (size) bytes from start address to end
address\n
ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n
in DDR data at <addr>, the command will read a 32-bit data\n
from <addr>, and write (data ^ bit_err) back to <addr>\n
Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used
for ddr3 commands and for now it's not needed any more.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds the DDR3 ECC support to enable ECC in the DDR3
EMIF controller for Keystone II devices.
By default, ECC will only be enabled if RMW is supported in the
DDR EMIF controller. The entire DDR memory will be scrubbed to
zero using an EDMA channel after ECC is enabled and before
u-boot is re-located to DDR memory.
An ecc_test environment variable is added for ECC testing.
If ecc_test is set to 0, a detection of 2-bit error will reset
the device, if ecc_test is set to 1, 2-bit error detection
will not reset the device, user can still boot the kernel to
check the ECC error handling in kernel.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Add functions to set/get SES PMAX values of Pivilege ID pair.
Also add msmc module definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The EDMA3 controller’s primary purpose is to service data transfers
that you program between two memory-mapped slave endpoints on the device.
Typical usage includes, but is not limited to the following:
- Servicing software-driven paging transfers (e.g., transfers from external
memory, such as SDRAM to internal device memory, such as DSP L2 SRAM)
- Servicing event-driven peripherals, such as a serial port
- Performing sorting or sub-frame extraction of various data structures
- Offloading data transfers from the main device DSP(s)
- See the device-specific data manual for specific peripherals that are
accessible via the EDMA3 controller
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
For K2E and K2L SoCs clock output from PASS PLL has to be enabled
after NETCP domain and PA module are enabled. So create new function
for that and call it after PA module is enabled.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The Keystone2 Edison SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Keystone2 Edison SoC uses the same keystone navigator, but
uses different NETCP PktDMA definitions. This patch adds
required definitions.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
With MAC_PHY sgmii configuration, u-boot checks PHY link status before
sending each packet. Increasing MDIO frequency increases overall tftp
speed. We set it to maximum 2.5MHz.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds Keystone II Lammar (K2L) EVM board support.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patches enables the On-chip Shared Ram clock domain for K2L SoC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The initialization of PLLs is a part of board specific code, so
move it appropriate places.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds Keystone II Lamar (K2L) SoC specific definitions
to support MSMC cache coherency.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds clock definitions and commands to support Keystone II
K2L SOC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds hardware definitions specific to Keystone II
Lamar (K2L) SoC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
