summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2020-02-09arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental ↵Lukasz Majewski
disablement The 'enable-active-high' DTS property configures GPIO so it is active with HIGH state (by default it is low). The 'regulator-boot-on' property indicates that the regulator was enabled in the 'earlier' stage - i.e. bootloader/firmware. In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in very early SPL code, so it shouldn't be modified at latter stages. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-02-09board: toradex: Add Verdin iMX8M Mini supportIgor Opaniuk
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-09arm: dts: imx8mm-pinfunc: sync latest linux-next pin func headerMarcel Ziswiler
Synchronise with latest linux-next kernel pin func header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-07board: presidio-asic: Add basic G3 engr. development board supportAlex Nemirovsky
Add basic Presidio G3 engineering board support Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07gpio: do not include <asm/arch/gpio.h> for Cortina CAxxxx SoCsJason Li
The Cortina CAxxxx GPIO driver maintains DM_GPIO support across different CPU ISA in the CAxxxx Soc Family; Not just ARM. Therefore, it is not desirable to split out and maintain separete gpio header file for each CPU architecture. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Jason Li <jason.li@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07mpc8xx: Expose show_regs()Tom Rini
To match the other PowerPC platforms the function show_regs() must not be marked static but instead be an exposed global function. Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Christophe Leroy <christophe.leroy@c-s.fr>
2020-02-07arm: dts: mediatek: add ethernet and sgmii dts node for mt7622MarkLee
This patch add eth and sgmii dts node for mt7622 to support ethernet Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
2020-02-06Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Gen 5 and Watchdog fixes
2020-02-05Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for ls1028a, add DM-I2C support, update secure boot header offset
2020-02-05Merge tag 'rpi-next-2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - DFU support file operations lager then the default max size - add dfu support to dwc2 for bcm2835 - enable DFU for RPi4 - Fix RPi4 memory map to include the genet device - add driver for the genet ethernet device - enable network support in RPi4 config
2020-02-05ddr: altera: Add DDR2 support to Gen5 driverMarek Vasut
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated by Quartus are named differently than the DDR3 ones, use anon unions to store them in the same structures, without growing their size. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-02-05watchdog: designware: Convert to DM and DT probingMarek Vasut
Convert the designware watchdog timer driver to DM and add DT probing support. Perform minor coding style clean up, like drop superfluous braces. These ought to be no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
2020-02-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Various minor fixes for x86 - Switch to ACPI mode on Intel edison - Support run-time configuration for NS16550 driver - Update coreboot and slimbootloader serial drivers to use NS16550 run-time configuration - ICH SPI driver fixes to hardware sequencing erase case - Move ITSS from Apollo Lake to a more generic location - Intel GPIO driver bug fixes - Move to vs2017-win2016 platform build host for Azure pipelines
2020-02-04dm: arm64: ls1012a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04armv8: fsl-layerscape: spl: fix build error when DM_I2C is enabledBiwen Li
Fix below SPL build error when DM_I2C is enabled, - arch/arm/cpu/armv8/built-in.o: In function `board_init_f: arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all' arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `i2c_init_all' make[2]: *** [spl/u-boot-spl] Error 1 make[1]: *** [spl/u-boot-spl] Error 2 make: *** [sub-make] Error 2 arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f': arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit declaration of function 'i2c_init_all'; did you mean 'misc_init_r'? [-Wimplicit-function-declaration]` Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: lx2160a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LX2160A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LS1028A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: fix interrupt propertiesMichael Walle
Sync the interrupt properties with the ones from Linux. Also use the constants provided by the dt-bindings header. Please note, that there are actual changes/fixes in the irq flags. U-Boot won't use the interrupt properties anyway. It's just to be consistent with the Linux device tree. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: ls1028a: use the new flexspi driverMichael Walle
Also align the fspi node with the kernel one. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04x86: itss: Remove apl-prefixWolfgang Wallner
The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so remove the apl-prefix of the implemented functions/structures/... Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: itss: Add a Kconfig option to enable/disable ITSS driverWolfgang Wallner
Add a Kconfig option to support enabling/disabling the inclusion of the ITSS driver depending on the platform. Atuomatically select the ITSS driver when building for Apollo Lake. Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: squashed in http://patchwork.ozlabs.org/patch/1232761/] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: Move itss.c from Apollo Lake to a more generic locationWolfgang Wallner
The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so move it to a common location within arch/x86. Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: conditionally build itss.c] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04arm: dts: k3-j721e-main: Add Support for gpio0Faiz Abbas
Add the main_gpio0 node. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable I2C expander for SPLVignesh Raghavendra
IO expanders are required to power cycle SD card. So enable the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Add I2C GPIO expanderVignesh Raghavendra
Add I2C GPIO expander required to power cycle MMC/SD Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e: Add I2C nodesVignesh Raghavendra
J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main domain. Add DT nodes for the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral modeVignesh Raghavendra
Enable USB0 in peripheral mode so that it be used for DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFUVignesh Raghavendra
Add support to download SYSFW into internal RAM via DFU in DFU boot mode. Prepare a DFU config entity entry dynamically using buffer address allocated for SYSFW and start DFU gadget to get SYSFW. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFUVignesh Raghavendra
J721e does not support USB Host MSC boot, but only supports DFU boot. Since BOOT_DEVICE_USB is often used for host boot mode and BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to BOOT_DEVICE_DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04x86: Move itss.h from Apollo Lake to the generic x86 include directoryWolfgang Wallner
The code in this file is not specific to Apollo Lake. According to coreboot sources (where this code comes from), it is common to at least: * Apollo Lake * Cannon Lake * Ice Lake * Skylake Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: apl: Add the term "Interrupt Timer Subsystem" to ITSS filesWolfgang Wallner
ITSS stands for "Interrupt Timer Subsystem", so add that term to the description of the relevant files. Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: limit the fs segment to the pointer sizeMasahiro Yamada
The fs segment is only used to get the global data pointer. If it is accessed beyond sizeof(new_gd->arch.gd_addr), it is a bug. To specify the byte-granule limit size, drop the G bit, so the flag field is 0x8093 instead of 0xc093, and set the limit field to sizeof(new_gd->arch.gd_addr) - 1. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: fixed the comments about FS segement] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: use invd instead of wbinvd in real mode start codeMasahiro Yamada
I do not know why the boot code immediately after the system reset should write-back the cache content. I think the cache invalidation should be enough. I tested this commit with qemu-x86_defconfig, and it worked for me. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: serial: Use NS16550_DYNAMIC in Slim BootloaderPark, Aiden
Slim Bootloader provides serial port info in its HOB to support both IO or MMIO serial ports, but it's controlled by SYS_NS16550_MEM32 or SYS_NS16550_PORT_MAPPED in U-Boot. To support both serial port configurations dynamically at runtime, Slim Bootloader serial driver leverages NS16550_DYNAMIC. Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: remove the obsolete comments for data->type] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: Move coreboot over to use the coreboot UARTSimon Glass
Use this UART to improve the compatibility of U-Boot when used as a coreboot payload. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-04x86: Update coreboot serial table structSimon Glass
Since mid 2016, coreboot has additional fields in the serial struct that it passes down to U-Boot. Add these so we are in sync. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-02-03ARM: socfpga: Drop last use of socfpga_reset_managerMarek Vasut
This particular chunk of code was not updated, likely due to the order in which the patches were posted and applied. Fix this missing part. Fixes: bb25aca13433 ("arm: socfpga: Convert reset manager from struct to defines") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2020-02-01Merge tag 'u-boot-rockchip-20200130' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Support redundant boot for rk3399 - Support binman for rockchip platform - Update ram driver and add ddr4 support for rk3328
2020-01-31Merge tag 'uniphier-v2020.04-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier UniPhier SoC updates for v2020.04 (2nd) Denali NAND driver changes: - Set up more registers in denali-spl for SOCFPGA - Make clocks optional - Do not assert reset signals in the remove hook - associate SPARE_AREA_SKIP_BYTES with DT compatible - switch to UCLASS_MTD UniPhier platform changes: - fix a bug in dram_init() - specify loadaddr for "source" command
2020-02-01ARM: uniphier: set gd->ram_base correctlyMasahiro Yamada
gd->ram_base is not set at all if the end address of the DRAM ch0 exceeds the 4GB limit. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01mtd: rawnand: denali_dt: use UCLASS_MTD instead of UCLASS_MISCMasahiro Yamada
UCLASS_MTD is a better fit for NAND drivers. Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile drivers/mtd/mtd-uclass.c Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig of this platform enables NAND_DENALI_DT. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2020-02-01ARM: uniphier: remove adhoc reset deassertion for the NAND controllerMasahiro Yamada
Now that the reset controlling of the Denali NAND driver (denali_dt.c) works for this platform, remove the adhoc reset deassert code. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-30rockchip: rk3308: add alias for emmc/sdmmcKever Yang
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30ram: rk3328: update lpddr3 settingYouMin Chen
update lpddr3 setting for fix init fail about "col error". Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30ram: rk3328: add support ddr4 initYouMin Chen
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init. Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: Add Single boot image (with binman, pad_cat)Jagan Teki
All rockchip platforms support TPL or SPL-based bootloader in mainline with U-Boot proper as final stage. For each stage we need to burn the image on to flash with respective offsets. This patch creates a single boot image component using - binman, for arm32 rockchip platforms - pad_cat, for arm64 rockchip platforms. This would help users to get rid of burning different boot stage images. The new image called 'u-boot-rockchip.bin' which can burn into flash like: ₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64 This would support all rockchip platforms, except rk3128 since it doesn't support for SPL yet. Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Cc: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30arm: dts: rk3188: Add rk3188-u-boot.dtsiJagan Teki
Add U-Boot specific dtsi file for rk3188 SoC. This would help to add U-Boot specific dts nodes, properties which are common across rk3188. Right now, the file is empty, will add required changes in future patches. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30arm: dts: rk3036: Add rk3036-u-boot.dtsiJagan Teki
Add U-Boot specific dtsi file for rk3036 SoC. This would help to add U-Boot specific dts nodes, properties which are common across rk3036. Right now, the file is empty, will add required changes in future patches. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: rk3399: Add bootcount supportJagan Teki
Add bootcount support for Rockchip rk3399. The bootcount value is preserved in PMU_SYS_REG0 register, this would help to support redundent boot. Once the redundant boot triggers, the altboot command will look for extlinux-rollback.conf on particular bootable partition which supposed to be a recovery partition where redundant boot required. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30rockchip: Add common reset causeJagan Teki
Add cpu reset cause in common cpu-info file. This would help to print the reset cause for various resets. Right now it support rk3288, rk3399. rest of rockchip platforms doesn't have reset cause support ye but this code is more feasible to extend the same. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
generated by cgit (git 2.34.1) at 2025-01-05 21:43:46 +0000