summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2019-10-25dts: mtmips: add clock node for mt7628Weijie Gao
This patch adds clkctrl node for mt7628 and adds clocks property for some node. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25dts: mtmips: enable high-speed UART support for mt7628Weijie Gao
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which support baudrate up to 921600. The high-speed UART is compatible with ns16550 when baudrate <= 115200. Add compatible string to dtsi file so u-boot can use it when serial_mtk driver is built in. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25dts: mtmips: move uart property clock-frequency into mt7628an.dtsiWeijie Gao
The UART of MT7628 has fixed 40MHz input clock so there is no need to put clock-frequency in every dts files. Just put it into the common dtsi file. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25mips: bmips: switch to board defines for dtbÁlvaro Fernández Rojas
Fixes commit 344db3f, which added missing bmips dtbs depending on their SoCs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: correct name charactersÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: enable vr-3032u nand supportÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: bcm63268: add support for brcmnandÁlvaro Fernández Rojas
BCM63268 uses 4.0 HW nand controller, which is currently supported by brcmnand driver. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: bcm6362: add support for brcmnandÁlvaro Fernández Rojas
BCM6362 uses old 2.2 HW nand controller, which isn't currently supported by brcmnand driver. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: bcm6328: add support for brcmnandÁlvaro Fernández Rojas
BCM6328 uses old 2.2 HW nand controller, which isn't currently supported by brcmnand driver. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25bmips: bcm6368: add support for brcmnandÁlvaro Fernández Rojas
BCM6368 uses old 2.1 HW nand controller, which isn't currently supported by brcmnand driver. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25MIPS: add compile time definition of L2 cache sizeRamon Fried
If configuration is set to skip low level init, automatic probe of L2 cache size is not performed and the size is set to 0. Flushing or invalidating the L2 cache will fail in this case. Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0. Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
2019-10-25sunxi: set PIO voltage to hardware-detected value on startup on H6Icenowy Zheng
The Allwinner H6 SoC has a register to set the PIO banks' voltage. When it mismatches the real voltage supplied to the VCC to the PIO supply, the PIO will work improperly. The PIO controller also has a register that contains the status of each VCC rail of the PIO supplies, and it has the same definition with the configuration register. so we can just copy the content of this register to the configuration register at startup, to ensure the configuration is correct at startup stage. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> [jagan: s/__maybe__unused/__maybe_unused] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25arm: dts: sync dts for Allwinner H6Clément Péron
Sync Kernel DTS for Allwinner H6 boards. Drop /omit-if-no-ref/ keyword as it's not supported by U-boot. commit <d45331b00ddb> Linux 5.3-rc4 Signed-off-by: Clément Péron <peron.clem@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25sunxi: Fix pll1 clock calculationStefan Mavrodiev
clock_sun6i.c is used for sun6i, sun8i and sun50i SoC families. PLL1 clock sets the default system clock, defined as: sun6i: 1008000000 sun8i: 1008000000 sun50i: 816000000 With the current calculation, m = 2 and k = 3. Solving for n, this results 28. Solving back: (24MHz * 28 * 3) / 2 = 1008MHz However if the requested clock is 816, n is 22.66 rounded to 22, which results: (24MHz * 28 * 3) / 2 = 792MHz Changing k to 4 satisfies both system clocks: (24E6 * 21 * 4) / 2 = 1008MHz (24E6 * 17 * 4) / 2 = 816MHz Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)Sunil Mohan Adapa
A64 OLinuXino board from Olimex has three variants with onboard eMMC: A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In addition, there are two variants without eMMC. One without eMMC and one with SPI flash. This suggests the need for separate device tree for the three eMMC variants. The Linux kernel upstream has chosen to create and use a separate device tree for the eMMC variants instead of adding eMMC support existing device tree. These changes to Linux kernel are queued for Linux 5.4. commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)") This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux device-tree and a64-olinuxino_defconfig. Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org> [jagan: updated linux-next commit details] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25sunxi: H6: DRAM: Add support for half DQJernej Skrabec
Half DQ configuration seems to be very rare for H6 based boards/STBs, but exists nevertheless. Currently the only known product which needs this support is Tanix TX6 mini. This commit adds support for half DQ configuration. Code was tested for regressions on other configurations (OrangePi 3 1 GiB/LPDDR3, Tanix TX6 4 GiB/DDR3) and none were found. Thanks to Icenowy Zheng for help with this code. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Tested-by: thomas graichen <thomas.graichen@gmail.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Maxime Ripard <mripard@kernel.org>
2019-10-25configs: sopine-baseboard: Enable SPI-FLASHJagan Teki
SoPine has winbond SPI-FLASH, so enable the same in defconfig and add aliases for spi0 in -u-boot.dtsi Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25arm: sunxi: Enable SPI/SPI-FLASH support for A64Jagan Teki
SPI is available in Allwinner A64 SoC, so enable it globally in Kconfig. - CONFIG_SPI - CONFIG_DM_SPI - CONFIG_DM_SPI_FLASH Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-24Merge branch '2019-10-24-UFS-support'Tom Rini
- Add Universal Flash Storage (UFS) support
2019-10-24microblaze: Fix tab indentation in start.SMichal Simek
Use tab instead of spaces. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24microblaze: Unify Linux bootm processMichal Simek
Record two bootstages and add "Starting kernel" message to have standard handoff message between U-Boot and OS. Also use debug() instead of #ifdef DEBUG to clean the code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24microblaze: Fix FDT message in boot_prep_linux()Michal Simek
There is no need to show FDT message in regular flow that's why switch it to debug level. Fixes: 0905046050b0 ("microblaze: Switch to generic bootm implementation") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add support for e-a2197-00 System ControllerMichal Simek
Add support for System Controller available on e-a2197-00 base board. System is very similar to p-a2197-00 board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24ARM: zynq: Remove unused board_early_init_f()Michal Simek
board_early_init_f added by commit e6cc3b25d721 ("arm: zynq: Wire watchdog internals") is no longer needed that's why remove it also with Kconfig enabling. Fixes: ccd063e9812a ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add support for zcu216Michal Simek
zcu104/6 defconfig was used as source. Standard features are enabled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add support for m-a2197-03Michal Simek
It is based on m-a2197-01 with some changes in i2c intrastructure. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add support for m-a2197-02Michal Simek
It is based on m-a2197-01 with some changes in i2c intrastructure. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: List lpd watchdog in dtsiMichal Simek
There are use cases where lpd watchdog can be configured for APU use. By design this IP should be listed in zynqmp.dtsi to make sure that node is properly enabled by DTG. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Use power header in zynqmp.dtsiMichal Simek
Use power header and add power-domains property. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Use reset header in zynqmp.dtsiMichal Simek
Wire reset-controller and use macros from reset header. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Use backward compatible string for gemMichal Simek
Add backward compatible string for gem ("cdns,gem"). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Switch to xlnx-zynqmp-clk headerMichal Simek
Use prepared header instead of hardcoded values. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Update nand device tree node propertiesNaga Sureshkumar Relli
This patch updates the nand device tree node properties as per updated driver. Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Fix DT style for ipi mailboxMichal Simek
Remove additional empty space. Fixes: 95497afada58 ("arm64: zynqmp: add firmware and mailbox node to DT") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24ARM: dt: Also clean dtbo filesMichal Simek
dtbo files can be also generated that's why also clean them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: versal: Fix sdhci node address for versal-mini-emmc1Michal Simek
Add missing trailing 0 to mach node name address with reg property. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Turn comment to gpio-line-namesMichal Simek
Label gpio lines properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add label property to all ina226 on zcu102Michal Simek
Label property is adding capability to distiguish chips from each other when iio framework is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu102Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: dt: Add optional gpio phy reset propertiesHarini Katakam
Add gpio phy reset via I2C expander TCA6416 on board ZCU102. A warning call trace is observer in probe when this reset is called from context that can sleep. Keep this commented until that is resolved in phylib. Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: dt: Add missing DP83867 quirkHarini Katakam
The DP83867 strap control workaround is already present in Linux kernel mainline binding. All these Xilinx boards require this quirk. Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable fpd_dma for zcu104 platformsMichal Simek
Enable fpd_dma for these boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu104Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add label property to all ina226 on zcu106Michal Simek
Label property is adding capability to distiguish chips from each other when iio framework is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Fix the si570 clock frequency on zcu111Venkatesh Yadav Abbarapu
The si570 clock frequency should be 156.25MHz as per datasheet. Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Add label property to all ina226 on zcu111Michal Simek
Label property is adding capability to distiguish chips from each other when iio framework is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: dt: Delete no-1-8-v property from zcu102-rev1.0T Karthik Reddy
Currently zcu102 Rev1.0 board includes RevA sdhci dt node which has no-1-8-v property. Since Rev1.0 has level shifters delete this property to enable support for 1.8v. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-13 20:07:53 +0000