| Age | Commit message (Collapse) | Author |
|---|
|
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
False multi-bit ECC errors will be reported by the eSDHC buffer which
can trigger a reset request.
We disable all ECC error checking on SDHC.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the needed defines and code to utilize the common 8xxx srio init
code to setup LAWs and modify device tree if we have SRIO enabled on a
board.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe
controllers for SRIO.
We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.
We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.
Introduced the following standard defines for board config.h:
CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available
(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)
[ These mimic what we have for PCI and PCIe controllers ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
This change does the following:
- Adds printing of negotiated link width. This information can be
useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
Previously boards that did not implement it would print unsightly
output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
clear that the "base address XYZ" value refers to the base address of
the internal processor PCIe registers and not a standard PCI BAR
value.
- Changes "PCIE" output to the standard "PCIe"
Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06
After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus. Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.
Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
We set the L1 dache register with a bogus register value. Need to be
using 'r3' instead of 'r0'.
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add spaces to cause the informational prints to line up with
the ones from init_func_ram() in board.c. Output now looks like
this:
....
DRAM: Detected 4096 MB of memory
This U-Boot only supports < 4G of DDR
You could rebuild it with CONFIG_PHYS_64BIT
DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off)
....
The prints from lbc_sdram_init() have also been modified to line
line up and changed to start with "LBC SDRAM" instead of the
confusing "SDRAM".
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This config option is for an erratum workaround; rename it to be more
clear. Also, drop it from config files don't need it and were
undefining it.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
sdram_init() is used to initialize sdram on the lbc. Rename it
accordingly.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts. Most
of the initdram() functions were identical, with 2 common differences:
1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others. I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.
2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document. It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled. This seems bad.
The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some platforms might want to override the default wimge=0 for
DDR. Add CONFIG_SYS_PPC_DDR_WIMGE for those platforms to use.
This will initially only be used by TQM85xx, but could be
useful for other boards or testing going forward. Note that
the name of this define is not 85xx-specific. WIMGE is a
fairly universal concept, so any ppc platforms that require
different WIMGE settings for DDR can use the same #define.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES. This mimics the code we have in place
for the 85xx platforms.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Created a section in the Makefile for SoC specific SERDES code. Also
added P1013 SERDES (use P1022 SERDES code).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Instead of a #define use a null weak function for fsl_serdes_init
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
|
|
Patch 8ef583a0 [miiphy: convert to linux/mii.h] introduced a small
problem in the ppc4xx miiphy.c version. This patch fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Patch "Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value"
(sha1: 25ddd1fb0a2281b182529afbc8fda5de2dc16d96)
introduce GENERATED_GBL_DATA_SIZE which is sizeof aligned gd_t
(currently 0x40).
Microblaze configs used 0x40(128) because this place also contained
board info structure which lies on the top of ram.
U-Boot is placed to the top of the ram (for example 0xd7ffffff)
and bd structure was moved out of ram.
This patch is fixing this scheme with GENERATED_BD_INFO_SIZE
which swap global data and board info structures.
For example:
Current: gd 0xd7ffffc0, bd 0xd8000000
Fixed: gd 0xd7ffffc0, bd 0xd7ffff90
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Microblaze implement enable/disable interrupts through MSR
that's why disable_interrupts function should return 1 when interrupt
was enabled. Return 0 when interrupt was disabled.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Curent U-Boot can boot zImage by use the "go" command.
But this is not right method. And this method can not set command-line
to linux kernel.
zimageboot sets command-line in environment of u-boot in linux kernel,
and provides function to boot it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
The register information of SCIF/SCI was compiled
by drivers/serial/serial_sh.h.
Therefore, these are not necessary.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
|
|
In some usages of inline assembly, hard-coded registers were
specified when a scratch register should have been used instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
The following commit:
commit 882b7d726febe65579d6502c271412ecb05821d7
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Oct 20 03:41:17 2010 -0400
do_reset: unify duplicate prototypes
missed the 74xx_7xx and mpc86xx arches and the ppmc7xx board do_reset()
functions which resulted in build errors such as:
cpu.c:128: error: conflicting types for 'do_reset'
include/command.h:102: error: previous declaration of 'do_reset' was here
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
By rearranging the linker script we get support for
relocation of -fpic for free.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Ths old comment was quite screwed up. Replace it with a new version
that should be a bit more descriptive.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Guido Classen <clagix@gmail.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
This patch adds the support MFP support for Marvell ARMADA100 SoCs
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
ARMADA 100 Family processors are highly integrated SoCs
based on Sheeva_88SV331x-v5 PJ1 cpu core.
Ref: http://www.marvell.com/products/processors/applications/armada_100
SoC versions Supported:
1) ARMADA168/88AP168 (Aspen P)
2) ARMADA166/88AP166 (Aspen M)
3) ARMADA162/88AP162 (Aspen L)
Contributors:
Eric Miao <eric.y.miao@gmail.com>
Lei Wen <leiwen@marvell.com>
Mahavir Jain <mjain@marvell.com>
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
