| Age | Commit message (Collapse) | Author |
|---|
|
Corrected the ranges table of the IFC node.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The unit-address should be the same as the I2C address of the device.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable ERRATUM_A009942 workaround for B-series and T-series platforms.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
|
|
Add missing L3 cache flush functionality which absence prevents
Linux kernel from normal boot in case the L3 cache is enabled
by ATF.
The L3 cache is named the "last level" cache in order to keep
the terminology similar to the ATF code.
This cache should not be disabled by u-boot since the Linux
kernel cannot activate it, so it is activates at ATF stage.
However the cache flush is required for preventing data corruption
after disabling the MMU and the data cache before passing control
to the loaded Linux image.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
The spi1 on CP1 is aliased as spi0 since this is the way
the driver enumerates it.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This is a user configurable option, but "select BLK" forces users to
enable it.
Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Sync with the latest kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Just a cosmetic cleanup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This will be used to store the return value of readl().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This function is not used anymore. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is not used anymore. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is not used anymore. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0
Commit-notes
When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c
I have a issue because gd->arch.timer_rate_hz = 0
For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.
But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.
For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.
static init_fnc_t init_sequence_f[] = {
....
arch_cpu_init_dm,
mark_bootstage, /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
defined(CONFIG_SPARC)
timer_init, /* initialize timer */
#endif
.......
To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...
It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC
and I don't sure of impact for other function called
(board_early_init_f for example....)
=> This patch solve issue only in timer armv7
get_boot_us() can be called everytime without div by 0 issue
(gd->arch.timer_rate_hz is not used)
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing
changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
|
|
|
|
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Series-to: sjg, agraf@suse.de
Series-cc: uboot
Series-version: 4
Series-changes: 2
- make ceva_init_sata static
- Move SATA_CEVA to defconfig
- Initalized max_lun and max_id platdata
Series-changes: 3
- Extend Kconfig help description
- sort dm.h
- Remove SPL undefinition from board file
- Fix Kconfig dependecies
|
|
Some Altera Quartus generated files have long lines that are split with a '\' at
the end of the line. It also wOn Windows, rites files in DOS format, which can
confuse some of the processing scripts in this file. This patch solves both issues.
Signed-off-by: Bill Randle <bill.randle@gmail.com>
Cc: Marek Vasut <marex@denx.de>
|
|
Valid Altera SoCFPGA preloader image must contain special data at
offsets 0x40, 0x44, 0x48 and valid instructions at address 0x4c or
0x50. These addresses are by default used by U-Boot's vector table
and a piece of reset handler, thus a valid preloader corrupts those
addresses slightly. While this works most of the time, this can and
does prevent the board from rebooting sometimes and triggering this
issue may even depend on compiler.
The problem is that when SoCFPGA performs warm reset, it checks the
addresses 0x40..0x4b in SRAM for a valid preloader signature and
header checksum. If those are found, it jumps to address 0x4c or
0x50 (this is unclear). These addresses are populated by the first
few instructions of arch/arm/cpu/armv7/start.S:
ffff0040 <data_abort>:
ffff0040: ebfffffe bl ffff0040 <data_abort>
ffff0044 <reset>:
ffff0044: ea000012 b ffff0094 <save_boot_params>
ffff0048 <save_boot_params_ret>:
ffff0048: e10f0000 mrs r0, CPSR
ffff004c: e200101f and r1, r0, #31
ffff0050: e331001a teq r1, #26
Without this patch, the CPU will enter the code at 0xffff004c or
0xffff0050 , at which point the value of r0 and r1 registers is
undefined. Moreover, jumping directly to the preloader entry point
at address 0xffff0000 will also fail, because address 0xffff004.
is invalid and contains the preloader magic.
Add BOOT0 hook which reserves the area at offset 0x40..0x5f and
populates offset 0x50 with jump to the entry point. This way, the
preloader signature is stored in reserved space and can not corrupt
the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
|
|
|
|
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add the name for register space and memory space.
<0x1550000 0x10000 > is the QSPI register space.
<0x40000000 0x4000000> is the QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
Not all memory is mapped in the MMU. So we need to restrict the memory
size so that U-Boot does not try to access it. Also, the internal
registers are located at 0xf000.0000 - 0xffff.ffff. Currently only 2GiB
are mapped for system memory. This is what we pass to the U-Boot
subsystem here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
To use the PCIe driver, its controller memory and the PCIe regions need
to get mapped in the MMU. Otherwise these areas can't be accessed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
The Armada8k implements 2 CPs (communication processors) and the 2nd
CP also is equipped with a COMPHY controller. This patch now loops
over all enabled MISC devices (CP110) enabled in the DT to initialize
all CPs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
Add I2C and SPI aliases to enable usage in U-Boot. Otherwise U-Boot will
not be able to use the SPI NOR chip for environment storage and use
"i2c dev 0" to select this I2C bus.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This patch adds the COMPHY device tree configuration to the DT file for
the Marvell DB-88F8040 devel board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This patch adds the COMPHY and UTMI device tree nodes to the cp110-slave
dtsi file for the Armada 8K.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
Since the cp110 slave also has comphy DT nodes, the names need to be
renamed to avoid a name clash. Lets use the common naming scheme:
"cpm_xxx" for master and "cps_xxx" for slave.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
To enable access to the slave CP its memory needs to be added to the
MMU memory map.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
Add the latest version of the DT files from the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
|
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
|
|
Add initial DTS support for AM571-IDK evm.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Sync all am57xx based dts files with latest Linux
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
