summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2016-04-08powerpc: mpc85xx: Enable pre-relocation malloc for MPC85xxmario.six@gdsys.cc
To enable DM on MPC85xx, we need pre-relocation malloc, which is implemented in this patch. We also make sure that the IVORs are always 4-aligned on e500 to prevent alignment exceptions caused by code changes in start.S. Signed-off-by: Mario Six <mario.six@gdsys.cc> Cc: York Sun <york.sun@nxp.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06spi: kirkwood_spi: Add support for multiple chip-selects on MVEBUStefan Roese
Currently only chip-select 0 is supported by the kirkwood SPI driver. The Armada XP / 38x SoCs also use this driver and support multiple chip selects. This patch adds support for multiple CS on MVEBU. The register definitions are restructured a bit with this patch. Grouping them to the corresponding registers. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-04-04Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-04-04ARM64: zynqmp: Select SYS_CONFIG_NAME via KconfigMichal Simek
This option enable adding new platform suport just by adding defconfig and DTS file which will target generic configuration for SoC. Make no sense to extend Kconfig just create a pointer between DTS and configuration file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04microblaze: Remove !OF_CONTROL code for timer and interruptMichal Simek
OF_CONTROL is enabled by default that's why this is dead code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04microblaze: Read information about timer/interrupts from DTMichal Simek
Read information about timer and interrupts from DT. This is the first small step to move timer and intc to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04net: gem: Allow to set the MAC from an EEPROMJoe Hershberger
Provide board specific option how to read MAC address from ROM. Do it in generic way to be reusable by differnet boards. If this is not enough board specific functions can be created. Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04arm: mvebu: Don't enable d-cache on A375Stefan Roese
Armada 375 still has some problems with d-cache enabled in the ethernet driver (mvpp2). So lets keep the d-cache disabled until this is solved. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-04-04arm: mvebu: Add basic support for Armada 375 eval board db-88f6720Stefan Roese
This patch adds basic support for the Marvell A375 eval board. Tested are the following interfaces: - I2C - SPI - SPI NOR - Ethernet (mvpp2), port 0 & 1 Currently the A375 SerDes and DDR3 init code is not intergrated. So the SPL U-Boot is not fully functional. Right now, this A375 mainline U-Boot can only be used by chainloading it via the original Marvell U-Boot. This can be done via this command: => tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000 Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-04-04arm: mvebu: Add basic support for the Marvell Armada 375 SoCStefan Roese
This patch adds basic support for the Armada 375. Please note that currently the SerDes and DDR3 init code for the A375 is not included / enabled. This will be done in a later, follow-up patch. Right now, this A375 mainline U-Boot can only be used by chainloading it via the original Marvell U-Boot. This can be done via this command: => tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000 Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-04-01board: Add Qualcomm Dragonboard 410C supportMateusz Kulikowski
This commit add support for 96Boards Dragonboard410C. It is board based on APQ8016 Qualcomm SoC, complying with 96boards specification. Features (present out of the box): - 4x Cortex A53 (ARMv8) - 2x USB Host port - 1x USB Device port - 4x LEDs - 1x HDMI connector - 1x uSD connector - 3x buttons (Power, Vol+, Vol-/Reset) - WIFI, Bluetooth with integrated antenna - 8GiB eMMC U-Boot boots chained with fastboot in 64-bit mode. For detailed build instructions see readme.txt in board directory. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01arm: Add support for Qualcomm Snapdragon familyMateusz Kulikowski
First supported chip is APQ8016 (that is compatible with MSM8916). Drivers in SoC code: - Reset controller (PSHOLD) - Clock controller (very simple clock configuration for MMC and UART) Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01spmi: Add sandbox test driverMateusz Kulikowski
This patch adds emulated spmi bus controller with part of pm8916 pmic on it to sandbox and tests validating SPMI uclass. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-04-01usb: Rename ehci-fsl.h to ehci-ci.hMateusz Kulikowski
Most of ehci-fsl header describe USB controller designed by Chipidea and used by various SoC vendors. This patch renames it to a generic header: ehci-ci.h Contents of file are not changed (so it contains several references to freescale SoCs). Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01sniper: Change vendor name from lge to lg, matching devicetree vendor prefixPaul Kocialkowski
This moves the sniper board from the lge to lg, in order to match the devicetree vendor prefix already defined in the kernel. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01arm: spl: Align default board_init_f comment with codeAndreas Dannenberg
The default board_init_f() implementation performs a call to board_init_r() as the last step of the sequence. Fix the comment for this function to reflect the actual execution flow. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2016-04-01rpi: BCM2837 and Raspberry Pi 3 32-bit supportStephen Warren
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with the CPU complex swapped out for a quad-core ARMv8. This can operate in 32- or 64-bit mode. 32-bit mode is the current default selected by the VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of U-Boot for the Raspberry Pi 3. >From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a change in usage of the SoC UARTs. On all previous Pis, the PL011 was the only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a UART to connect to the SoC. By default, the PL011 is used for this purpose since it has larger FIFOs than the other "mini" UART. However, this can be configured via the VideoCore firmware's config.txt file. This patch hard-codes use of the mini UART in the RPi 3 port. If your system uses the PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot port instead. A future change might determine which UART to use at run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed together. The mini UART has some limitations. One externally visible issue in the BCM2837 integration is that the UART divides the SoC's "core clock" to generate the baud rate. The core clock is typically variable, and under control of the VideoCore firmware for thermal management reasons. If the VC FW does modify the core clock rate, UART communication will be corrupted since the baud rate will vary from the expected value. This was not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To work around this, the VideoCore firmware can be told not to modify the SoC core clock. However, the only way this can happen and be thermally safe is to limit the core clock to a low/minimum frequency. This leaves performance on the table for use-cases that don't care about a UART console. Consequently, use of the mini UART console must be explicitly requested by entering the following line into config.txt: enable_uart=1 A recent version of the VC firmware is required to ensure that the mini UART is fully and correctly initialized by the VC FW; at least firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on core clock See: https://github.com/raspberrypi/firmware/issues/572". Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01ARM: bcm2835: expand Kconfig target descriptionsStephen Warren
This adds an explanation of which Raspberry Pi models each target option supports. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01ARM: bcm2835: move CONFIG_BCM283* to KconfigStephen Warren
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01ARM: keystone2: Add missing privilege ID settingsNishanth Menon
Add missing Privilege ID settings for KS2 SoCs. Based on: K2H/K: Table 6-7. Privilege ID Settings from SPRS866E (Nov 2013) http://www.ti.com/lit/ds/symlink/66ak2h14.pdf (page 99) K2L: Table 7-7. Privilege ID Settings from SPRS930 (April 2015) http://www.ti.com/lit/ds/symlink/66ak2l06.pdf (page 71) K2E: Table 7-7. Privilege ID Settings from SPRS865D (Mar 2015) http://www.ti.com/lit/ds/symlink/66ak2e05.pdf (page 75) K2G: Table 3-16. PrivIDs from SPRUHY8 (Jan 2016) http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf (page 238) Overall mapping: -------+-----------+-----------+-----------+--------- PrivID | KS2H/K | K2L | K2E | K2G -------+-----------+-----------+-----------+--------- 0 | C66x 0 | C66x 0 | C66x 0 | C66x 0 1 | C66x 1 | C66x 1 | Reserved | ARM 2 | C66x 2 | C66x 2 | Reserved | ICSS0 3 | C66x 3 | C66x 3 | Reserved | ICSS1 4 | C66x 4 | Reserved | Reserved | NETCP 5 | C66x 5 | Reserved | Reserved | CPIE 6 | C66x 6 | Reserved | Reserved | USB 7 | C66x 7 | Reserved | Reserved | Reserved 8 | ARM | ARM | ARM | MLB 9 | NetCP | NetCP | NetCP | PMMC 10 | QM_PDSP | QM_PDSP | QM_PDSP | DSS 11 | PCIe_0 | PCIe_0 | PCIe_0 | MMC 12 | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP 13 | Reserved | Reserved | PCIe_1 | Reserved 14 | HyperLink | PCIe_1 | HyperLink | Reserved 15 | Reserved | Reserved | TSIP | Reserved -------+-----------+-----------+-----------+--------- NOTE: Few of these might have default configurations, however, since most are software configurable, it is better to explicitly configure the system to have a known default state. Without programming these, we end up seeing lack of coherency on certain peripherals resulting in inexplicable failures (such as USB peripheral's DMA data not appearing on ARM etc and weird workarounds being done by drivers including cache flushes which tend to have system wide performance impact). By marking these segments as shared, we also ensure SoC wide coherency is enabled. Reported-by: Bin Liu <b-liu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01ARM: keystone2: Refactor MSMC macros to avoid #ifdefferyNishanth Menon
MSMC segment Privilege ID is not consistent accross the keystone2 SoCs. As the first step to ensure complete SoC wide coherency setup, lets refactor the macros to remove the #if-deffery around the code which obfuscates which IDs are actually enabled for which SoC. As a result of this change the PCIe configuration is moved after the msmc configuration is complete, but that should ideally have no functional impact. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01arm: clang: Update support slightlyTom Rini
- Move most of the flags required into LLVM_RELFLAGS to test at build time instead of requiring them to be passed in. - Update doc/README.clang to reflect this - Switch to rpi_2 as the example as it's closer to working out of the box than rpi is. Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-01Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-04-01sunxi: Add Pine64+ supportSiarhei Siamashka
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of running AArch64 code and thus is the first of its kind for the sunxi target. This patch adds a defconfig and device tree chunks for it. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [agraf: Change patch description] Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Add support for Allwinner A64 SoCsSiarhei Siamashka
The Allwinner A64 SoC is used in the Pine64. This patch adds all bits necessary to compile U-Boot for it running in AArch64 mode. Unfortunately SPL is not ready yet due to legal problems, so we need to boot using the binary boot0 for now. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [agraf: remove SPL code, move to AArch64] Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Explicitly cast u32 pointer conversionsAlexander Graf
Some parts of the sunxi code cast explicitly between u32 values and pointers. This is not a problem in practice, because all 64bit SoCs today only use the lower 32 bits for their phyical address space. But we need to make sure that the compiler is sure this is not an accident as well. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Depend SPL configs on SUPPORT_SPLAlexander Graf
We currently depend SPL config options on specific machine types which doesn't scale. Fortunately there's already a kconfig variable that tells us whether we want to build SPL code at all, so just depend them on this. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Move cpu independent code to mach directoryAlexander Graf
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while most of it is just generic code that could as well be used on an AArch64 SoC. Move all files that are not really tied to armv7 into a new mach-sunxi directory. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Enable USB nodes for H8Homlet v2Chen-Yu Tsai
This provides the minimal changes to the H8Homlet v2 dts to enable USB in U-boot. It is not what will be submitted to the kernel. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Enable USB on Cubietruck PlusChen-Yu Tsai
This provides the minimal changes to the Cubietruck Plus dts to enable USB in U-boot. It is not what will be submitted to the kernel. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01sunxi: Add USB and R_PIO nodes to sun8i-a83t.dtsiChen-Yu Tsai
This provides the minimal changes to the A83T dtsi to enable USB in U-boot. It is not what will be submitted to the kernel. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01cosmetic: Fix typos "privide"Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: rename function names ph1_* to uniphier_*Masahiro Yamada
Eliminate the "ph1"_ prefixes from function names because "uniphier_" describes the SoC familiy better. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: add pin-mux settings for NAND, eMMC, SD of PH1-sLD3Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: enable eMMC on PH1-sLD3 reference boardMasahiro Yamada
On PH1-sLD3, eMMC and NAND are assigned to different I/O pins. Both devices can be enabled at the same time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: adjust dram_init() and dram_init_banksize() for ARM64Masahiro Yamada
Currently, these functions assume #address-cells and #size-cells are both one. Fix them to support 64bit DTB. Also, I am fixing a buffer overrun bug while I am here. The array size of gd->bd->bd_dram is CONFIG_NR_DRAM_BANKS. The number of iteration in the loop should be limited by that CONFIG. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: dts: uniphier: add NAND pinmux nodeMasahiro Yamada
This will be used to set up pin-muxing for the NAND controller. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: dts: uniphier: add clock-frequency to serial nodes of LD11/LD20Masahiro Yamada
Since no clock driver is implemented for peripherals in U-Boot yet, this property is needed for the serial driver to set up the divisor register. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-31sunxi: clk: Fix USB PHY clock macros for A83TChen-Yu Tsai
The A83T has 3 PHYs, the last one being HSIC, which has 2 clocks. Also there is only 1 OHCI. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31sunxi: usb_phy: Add support for A83T USB PHYsChen-Yu Tsai
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host, 1 for USB HSIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31sunxi: Print soc-id from sram controller for sun8i boardsHans de Goede
As the need for various magic sram pokes has shown this maybe useful info to have. e.g. this shows one of my a23 tablets having an id of 1661 rather then the usual 1650 for the a23. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-31sunxi: Add conditional magic sram poke for A33Hans de Goede
I noticed that for certain SoC versions boot0 does a magic poke when build for A33. I'm not aware of this actually being necessary anywhere, but better safe then sorry. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-29Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-03-29Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-03-29ARM: tegra210: set PLLE_PTS bit when enabling PLLEStephen Warren
This bit needs to be set for system suspend/resume to work. This setting will be documented in an updated TRM at some time in the future. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-03-29armv8/ls2080ardb: Enable VID supportRai Harninder
This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8/ls1043aqds: dts: Set SPI mode for DSPIQianyu Gong
Clock phase and polarity for DSPI flash need to be set. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8: fsl-layerscape: Add LS1023A SVRMingkai Hu
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8: fsl-layerscape: Fix LS1043A SVR registerMingkai Hu
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8: fsl-lsch3: Disable SMMU during secure bootSaksham Jain
During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs to be put in bypass mode in uboot to enable CAAM transcations to pass through. For non-secure boot, SP BootROM doesn't enable SMMU, which is in bypass mode out of reset. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-26 07:29:41 +0000