summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2014-10-23omap3: Kconfig: fix the cm-t35 board option promptIgor Grinberg
The cm-t35 board support covers both cm-t3530 and cm-t3730 boards. Mention both boards in the Kconfig option prompt. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-23ARM: keystone: cmd_ddr3: add ddr3 commands to test ddrHao Zhang
Add ddr3 commands: test <start_addr in hex> <end_addr in hex> - test DDR from start\n address to end address\n ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n compare DDR data of (size) bytes from start address to end address\n ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n in DDR data at <addr>, the command will read a 32-bit data\n from <addr>, and write (data ^ bit_err) back to <addr>\n Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used for ddr3 commands and for now it's not needed any more. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: ecc: add ddr3 error detection and correction supportVitaly Andrianov
This patch adds the DDR3 ECC support to enable ECC in the DDR3 EMIF controller for Keystone II devices. By default, ECC will only be enabled if RMW is supported in the DDR EMIF controller. The entire DDR memory will be scrubbed to zero using an EDMA channel after ECC is enabled and before u-boot is re-located to DDR memory. An ecc_test environment variable is added for ECC testing. If ecc_test is set to 0, a detection of 2-bit error will reset the device, if ecc_test is set to 1, 2-bit error detection will not reset the device, user can still boot the kernel to check the ECC error handling in kernel. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone: msmc: extend functionality of SESVitaly Andrianov
Add functions to set/get SES PMAX values of Pivilege ID pair. Also add msmc module definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23dma: ti-edma3: introduce edma3 driverKhoronzhuk, Ivan
The EDMA3 controller’s primary purpose is to service data transfers that you program between two memory-mapped slave endpoints on the device. Typical usage includes, but is not limited to the following: - Servicing software-driven paging transfers (e.g., transfers from external memory, such as SDRAM to internal device memory, such as DSP L2 SRAM) - Servicing event-driven peripherals, such as a serial port - Performing sorting or sub-frame extraction of various data structures - Offloading data transfers from the main device DSP(s) - See the device-specific data manual for specific peripherals that are accessible via the EDMA3 controller Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone: clock: add support for K2E SoCsKhoronzhuk, Ivan
For K2E and K2L SoCs clock output from PASS PLL has to be enabled after NETCP domain and PA module are enabled. So create new function for that and call it after PA module is enabled. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: add Keystone2 K2E SoC supportKhoronzhuk, Ivan
The Keystone2 Edison SoC uses the same keystone net driver. This patch adds opportunity to use it by K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_serdes: add keystone K2E SoC supportKhoronzhuk, Ivan
Keystone2 Edison SoC uses the same keystone SerDes driver. This patch adds support for K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone2: keysonte_nav: add support for K2E SoCKhoronzhuk, Ivan
Keystone2 Edison SoC uses the same keystone navigator, but uses different NETCP PktDMA definitions. This patch adds required definitions. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: register eth PHYs on MDIO busKhoronzhuk, Ivan
As MDIO bus has been added we can register PHYs with it. After registration, the PHY driver will be probed according to the hardware on board. Startup PHY at the ethernet open. Use phy_startup() instead of keystone_get_link_status() when eth open, as it verifies PHY link inside and SGMII link is checked before. For K2HK evm PHY configuration at init was absent, so don't enable phy config at init for k2hk evm. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: generalize to be used by other sub systemsHao Zhang
SerDes driver is used by other sub systems like PCI, sRIO etc. So modify it to be more general. The SerDes driver provides common API's that can also be extended for other peripherals SerDes configurations. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: enhance to use cmu/comlane/lane specific configurationsHao Zhang
Enhance the driver to use cmu/comlane/lane specific configurations instead of 1 big array of configuration. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: create a separate SGMII SerDes driverKhoronzhuk, Ivan
This patch split the Keystone II SGMII SerDes related code from Ethernet driver and create a separate SGMII SerDes driver. The SerDes driver can be used by others keystone subsystems like PCI, sRIO, so move it to driver/soc/keystone directory. Add soc specific drivers directory like in the Linux kernel. It is going to be used by keysotone soc specific drivers. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: increase MDIO clock frequencyVitaly Andrianov
With MAC_PHY sgmii configuration, u-boot checks PHY link status before sending each packet. Increasing MDIO frequency increases overall tftp speed. We set it to maximum 2.5MHz. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: move header file from arch to ti-commonKhoronzhuk, Ivan
The header file for the driver should be in correct place. So move it to "arch/arm/include/asm/ti-common/keystone_net.h" and correct driver's external dependencies. At the same time align and correct some definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: add support for NETCP v1.5Khoronzhuk, Ivan
Currently the network driver is used only by k2hk evm board. The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e contain NETCP v1.5. So driver should be able to work with such kind of NETCP. This commit adds this opportunity. The main difference in masks and some registers, the logic is the same, so only definitions should be changed. To differentiate between versions add KS2_NETCP_V1_0 and KS2_NETCP_V1_5. Also remove unused and no more needed defines. The port number is specific for each board so move this parameter to configuration. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: remove SoC specific emac_regs structureHao Zhang
This patch removes K2HK SOC specifc emac_regs structure, it uses soc specific register offset to keep the network driver common across all the Keystone II EVMs. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: k2l-evm: add board supportHao Zhang
This patch adds Keystone II Lammar (K2L) EVM board support. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: enable OSR clock domain for K2L SoCHao Zhang
This patches enables the On-chip Shared Ram clock domain for K2L SoC. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone2: spl: move board specific codeHao Zhang
The initialization of PLLs is a part of board specific code, so move it appropriate places. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: msmc: add MSMC cache coherency support for K2L SOCHao Zhang
This patch adds Keystone II Lamar (K2L) SoC specific definitions to support MSMC cache coherency. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: clock: add K2L clock definitions and commandsHao Zhang
This patch adds clock definitions and commands to support Keystone II K2L SOC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone2: add K2L device hardware definitionsHao Zhang
This patch adds hardware definitions specific to Keystone II Lamar (K2L) SoC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: cmd_clock: generalize command usage descriptionKhoronzhuk, Ivan
The usage description of commands refers to headers of sources, that is not correct. This patch is intended to fix it. Also generalize code in order to reduce SoC dependent #ifdefs. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone: usb: add support of usb xhciWingMan Kwok
Add support of usb xhci. xHCI controls all USB speeds of the Host mode, that is, the SS through the SS PHY, as well as the HS, FS, and LS through the USB2 PHY. xHCI replaces and supersedes all previous host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not backwards compatible with any of them. The USB3SS’s USB Controller is fully compliant with xHC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23dma: keystone_nav: generalize driver usageKhoronzhuk, Ivan
The keystone_nav driver is general driver intended to be used for working with queue manager and pktdma for different IPs like NETCP, AIF, FFTC, etc. So the it's API shouldn't be named like it works only with one of them, it should be general names. The names with prefix like netcp_* rather do for drivers/net/keystone_net.c driver. So it's good to generalize this driver to be used for different IP's and delete confusion with real NETCP driver. The current netcp_* functions of keystone navigator can be used for other settings of pktdma, not only for NETCP. The API of this driver is used by the keystone_net driver to work with NETCP, so net driver also should be corrected. For convenience collect pkdma configurations in drivers/dma/keystone_nav_cfg.c. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23dma: keystone_nav: move keystone_nav driver to driver/dma/Khoronzhuk, Ivan
The keystone_nav is used by drivers/net/keystone_net.c driver to send and receive packets, but currently it's placed at keystone arch sources. So it should be in the drivers directory also. It's separate driver that can be used for sending and receiving pktdma packets by others drivers also. This patch just move this driver to appropriate directory and doesn't add any functional changes. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: keystone_nav: don't use hard addresses in netcp_pktdmaKhoronzhuk, Ivan
Use definitions in netcp_pktdma instead direct addresses. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: keystone_nav: don't use hard addresses in qm_configKhoronzhuk, Ivan
Use definitions in qm_config. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-22Merge git://git.denx.de/u-boot-dmTom Rini
2014-10-22dm: rpi: Convert GPIO driver to driver modelSimon Glass
Convert the BCM2835 GPIO driver to use driver model, and switch over Raspberry Pi to use this, since it is the only board. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2014-10-22dm: imx: i2c: Use gpio_request() to request GPIOsSimon Glass
GPIOs should be requested before use. Without this, driver model will not permit the GPIO to be used. Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-22imx: Add error checking to setup_i2c()Simon Glass
Since this function can fail, check its return value. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-10-22dm: tegra: spi: Convert to driver modelSimon Glass
This converts the Tegra SPI drivers to use driver model. This is tested on: - Tegra20 - trimslice - Tegra30 - beaver - Tegra124 - dalmore (not tested on Tegra124) Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: tegra: dts: Add aliases for spi on tegra30 boardsSimon Glass
All boards with a SPI interface have a suitable spi alias except the tegra30 boards. Add these missing aliases. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22dm: sf: sandbox: Convert SPI flash driver to driver modelSimon Glass
Convert sandbox's spi flash emulation driver to use driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22exynos: universal_c210: Move to driver model soft_spiSimon Glass
Adjust this board to use the driver model soft_spi implementation. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22dm: exynos: Convert SPI to driver modelSimon Glass
Move the exynos SPI driver over to driver model. This removes quite a bit of boilerplate from the driver, although it adds some for driver model. A few device tree additions are needed to make the SPI flash available. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22dm: sandbox: spi: Move to driver modelSimon Glass
Adjust the sandbox SPI driver to support driver model and move sandbox over to driver model for SPI. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22sandbox: dts: Add a SPI device and cros_ec deviceSimon Glass
Add a SPI device which can be used for testing SPI flash features in sandbox. Also add a cros_ec device since with driver model the Chrome OS EC emulation will not otherwise be available. Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Mark exynos5 console as pre-relocSimon Glass
We will need the console before relocation, so mark it that way. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: gpio: Convert to driver modelSimon Glass
Convert the exynos GPIO driver to driver model. This implements the generic GPIO interface but not the extra Exynos-specific functions. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Make sure that GPIOs are requestedSimon Glass
With driver model GPIOs must be requested before use. Make sure this is done correctly. (Note that the soft SPI part of universal is omitted, since this driver is about to be replaced with a driver-model-aware version) Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Tidy up GPIO headersSimon Glass
The wrong header is being included, thus requiring the code to re-declare the generic GPIO interface in each GPIO header. Fix this. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Add pinctrl settings for s5p_goniSimon Glass
These describe the GPIOs in enough detail for U-Boot's GPIO driver to operate. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Add pinctrl settings for smdkc100Simon Glass
These describe the GPIOs in enough detail for U-Boot's GPIO driver to operate. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: dts: Adjust device tree files for U-BootSimon Glass
The pinctrl bindings used by Linux are an incomplete description of the hardware. It is possible in most cases to determine the register address of each, but not in all cases. By adding an additional property we can fix this, and avoid adding a table to U-Boot for every single Exynos SOC. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: dts: Remove unused pinctrl information to save spaceSimon Glass
We don't include the pinctrl functions for U-Boot as they use up quite a bit of space and are not used. We could instead perhaps eliminate this material with fdtgrep, but so far this tool has not made it to upstream. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Bring in pinctrl dts files from Linux kernelSimon Glass
Bring in required device tree files for pinctrl from Linux v3.14. These are initially unchanged and have a number of pieces not needed by U-Boot. Note that exynos5420 is renamed to exynos54xx here since we want to support exynos5422 also. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: dts: Convert /include/ to #includeSimon Glass
We should be consistent about this. The kernel has moved to #include which breaks error reporting to some extent but does allow us to include binding files. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-30 20:31:49 +0000