summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2015-04-16sandbox: Update device tree 'reg' properties for I2C and SPISimon Glass
We should have a size value for these. Add one in each case. This will be needed for PCI. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-16x86: Add support for panther (Asus Chromebox)Simon Glass
Support running U-Boot as a coreboot payload. Tested peripherals include: - Video (HDMI and DisplayPort) - SATA disk - Gigabit Ethernet - SPI flash USB3 does not work. This may be a problem with the USB3 PCI driver or something in the USB3 stack and has not been investigated So far this is disabled. The SD card slot also does not work. For video, coreboot will need to run the OPROM to set this up. With this board, bare support (running without coreboot) is not available as yet. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-16x86: Support machines with >4GB of RAMSimon Glass
Some systems have more than 4GB of RAM. U-Boot can only place things below 4GB so any memory above that should not be used. Ignore any such memory so that the memory size will not exceed the maximum. This prevents gd->ram_size exceeding 4GB which causes problems for PCI devices which use DMA. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-16ti: dwc3: Enable clocks in enable_basic_clocks() in hw_data.cKishon Vijay Abraham I
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY) changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between the two dwc3 controllers present in dra7xx/am43xx and enabled these clocks in enable_basic_clocks() in hw_data.c. However these clocks continued to be enabled in board files/driver files for dwc3 host mode functionality causing compilation break with few configs. Fixed it here by making all the clocks enabled in enable_basic_clocks() and removing it from board files/driver files here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-16Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2015-04-15sunxi: Complete i2c support for each supported platformPaul Kocialkowski
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms even have up to 5. This adds support for every controller on each supported platform, which is especially useful when using expansion ports on single-board- computers. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15i2c: mvtwsi: Support for up to 4 different controllersPaul Kocialkowski
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI controller. However, other platforms using MVTWSI may come with more: this is the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found on the same chip. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: usbc: Wait for vbus to fall after disabling itHans de Goede
When u-boot boots the board may be powering vbus, we turn off vbus in sunxi_usbc_request_resources, if we are too quick with reading vusb-detect after this we may see a residual charge and assume we've an external vusb connected even though we do not. So when we see an external vusb wait a bit and try again. Without this when dealing with a pmic controller vbus and doing "reset" on the u-boot console the musb host will only init once every other boot, because the other boot it thinks an external vbus is present, this commit fixes this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15sunxi: usbc: Initialize vusb value on request_resourcesHans de Goede
On boards which use the pmic to enable/disable vbus on the otg port, the vbus value is not reset to 0 on reset, as reset only resets the SoC and not the pmic, so explicitly set vbus to 0 on init (request_resources) by moving the gpio_direction_output call into request_resources. For consistency also move the gpio_direction_input call for vbus-detect into request_resources. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15sunxi: Complete mmc pin mux for each supported platform, configured with KconfigPaul Kocialkowski
Sunxi platforms have different possible mmc pin mux setups (except for mmc0), which are different across platforms. This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig options. This is especially relevant when a second (in addition to mmc0) port is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: GPIO pin mux hardware-feature-specific function index definesPaul Kocialkowski
Each hardware feature exposed through the GPIO pin mux is usually using the same function index (for a given port), so there is no need to define one value per pin: one value per hardware feature per port is sufficient, avoids duplication and makes everything easier to understand. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: common VBUS detection logic in usbcPaul Kocialkowski
VBUS detection could be needed not only by the musb code (to prevent host mode), but also by e.g. gadget drivers to start only when a cable is connected. In addition, this allows more flexibility in vbus detection, as it could easily be extended to other USBC indexes. Eventually, this would help making musb support independent from a hardcoded USB controller index (0). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: usb: Drop AXP-sepcific VBUS detection and drive logicPaul Kocialkowski
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB code has to use GPIO in every case and let sunxi_gpio do the heavy lifting. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15power: axp221: Virtual VBUS detect and enable GPIOs to replace separate logicPaul Kocialkowski
This converts the VBUS detection and enable logic to GPIO instead of separate axp functions and checks that have to be used aside usual GPIO functions. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: gpio: Indentation fixPaul Kocialkowski
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-14board: ti: AM43xx: added USB initializtion codeKishon Vijay Abraham I
Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in am43xx board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14board: ti: DRA7: added USB initializtion codeKishon Vijay Abraham I
Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in dra7xx board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14include: asm: types: add resource_size_t typeKishon Vijay Abraham I
Added resource_size_t type in order to get rid of the following compilation error whiel building dwc3 gadget. include/linux/ioport.h:19:2: error: unknown type name ‘resource_size_t’ Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14arm: asm: dma-mapping: added dma_free_coherent APIKishon Vijay Abraham I
Added dma_free_coherent corresponding to the dma_alloc_coherent in dma-mapping.h in order to free memory allocated using dma_alloc_coherent. This API is used in dwc3 driver. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14include: asm: dma-mapping: get rid of the compilation warning in udc-coreKishon Vijay Abraham I
Fixed the following warning here. "warning: ‘dma_alloc_coherent’ defined but not used" while compiling udc-core Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14ARM: AM43xx: Enable clocks for USB OTGSS and USB PHYKishon Vijay Abraham I
Enabled clocks for dwc3 controller and USB PHY present in AM43xx. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14ARM: DRA7: Enable clocks for USB OTGSS and USB PHYKishon Vijay Abraham I
Enabled clocks for dwc3 controller and USB PHY present in DRA7. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14ARM: bcm2835: use phys_to_bus() for mboxStephen Warren
When we communicate with the VideoCore to perform property mailbox transactions, that is a DMA operation as far as the property buffer is concerned. Use phys_to_bus() on that buffer. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14ARM: bcm2835: implement phys_to_bus/bus_to_physStephen Warren
The BCM283[56] contain both a L1 and L2 cache between the GPU (a/k/a VideoCore CPU?) and DRAM. DMA-capable peripherals can also optionally access DRAM via this same L2 cache (although they always bypass the L1 cache). Peripherals select whether to use or bypass the cache via the top two bits of the bus address. An IOMMU exists between the ARM CPU and the rest of the system. This controls whether the ARM CPU's accesses use or bypass the L1 and/or L2 cache. This IOMMU is configured/controlled exclusively by the VideoCore CPU. In order for DRAM accesses made by the ARM core to be coherent with accesses made by other DMA peripherals, we must program a bus address into those peripherals that causes the peripheral's accesses to use the same set of caches that the ARM core's accesses will use. On the RPi1, the VideoCore firmware sets up the IOMMU to enable use of the L2 cache. This corresponds to addresses based at 0x40000000. On the RPi2, the VideoCore firmware sets up the IOMMU to disable use of the L2 cache. This corresponds to addresses based at 0xc0000000. This patch implements U-Boot's phys_to_bus/bus_to_phys APIs according to those rules. For full details of this setup, please see Dom Cobley's description at: http://lists.denx.de/pipermail/u-boot/2015-March/208201.html http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/215038 https://www.mail-archive.com/u-boot@lists.denx.de/msg166568.html Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-13break build if it would produce broken binaryPavel Machek
Add an error in known-bad case so that we don't produce broken and hard to debug binaries. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-04-13ARM: rpi: add a couple more revision IDsStephen Warren
According to Gordon Henderson's WiringPi library, there are some more Pi revision IDs out there. Add support for them. http://git.drogon.net/?p=wiringPi;a=blob_plain;f=wiringPi/wiringPi.c;hb=5edd177112c99416f68ba3e8c6c4db6ed942e796 At least ID 0x13 is out in the wild: Reported-by: Chee-Yang Chau <cychau@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-11ARM: fix arch/arm/Makefile for TegraMasahiro Yamada
Since commit 79d75d752717 (ARM: move -march=* and -mtune= options to arch/arm/Makefile), all the Tegra boards are broken because the SPL is built for ARMv7. Insert Tegra-specific code to arch/arm/Makefile to set compiler flags for an earlier ARM architecture. Note: The v1 patch for commit 79d75d752717 *was* correct when it was submitted. Notice it was originally written for multi .config configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for Tegra U-Boot Main/SPL, respectively. But, until it was merged into the mainline, commit e02ee2548afe (kconfig: switch to single .config configuration) had been already applied there. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Stephen Warren <swarren@nvidia.com> Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
2015-04-11arm: armada-xp: Fix SPL for AXP by using save_boot_params_retStefan Roese
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced a different method to return from save_boot_params(). The SPL support for AXP has been pulled and changing to this new method is now required for SPL to work correctly. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-04-10Merge git://git.denx.de/u-boot-arcTom Rini
2015-04-10arc: fix separate compilation of start.oAlexey Brodkin
While testing "arc: make sure _start is in the beginning of .text section" I haven't done proper clean-up of built binaries and so missed another tiny bit that lead to the following error: --->8--- LD u-boot arc-linux-ld.bfd: cannot find arch/arc/lib/start.o Makefile:1107: recipe for target 'u-boot' failed make: *** [u-boot] Error 1 --->8--- Fix is trivial: put "start.o" in "extra-y". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-10Merge branch 'master' of git://git.denx.de/u-boot-fdtTom Rini
2015-04-10arc: make sure _start is in the beginning of .text sectionAlexey Brodkin
This is important to have entry point in the beginning of .text section because it allows simple loading and execution of U-Boot. For example pre-bootloader loads U-Boot in memory starting from offset 0x81000000 and then just jumps to the same address. Otherwise pre-bootloader would need to find-out where entry-point is. In its turn if it deals with binary image of U-Boot there's no way for pre-bootloader to get required value. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-10fdt: nios: Fix warning in ft_cpu_setup()Simon Glass
This function should not return a value. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Thomas Chou <thomas@wytron.com.tw>
2015-04-10lpc32xx: add support for board work_92105Albert ARIBAUD \(3ADEV\)
Work_92105 from Work Microwave is an LPC3250- based board with the following features: - 64MB or 128MB SDR DRAM - 1 GB SLC NAND, managed through MLC controller. - Ethernet - Ethernet + PHY SMSC8710 - I2C: - EEPROM (24M01-compatible) - RTC (DS1374-compatible) - Temperature sensor (DS620) - DACs (2 x MAX518) - SPI (through SSP interface) - Port expander MAX6957 - LCD display (HD44780-compatible), controlled through the port expander and DACs This board has SPL support, and uses the LPC32XX boot image format. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add LPC32xx SSP support (SPI mode)Albert ARIBAUD \(3ADEV\)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add GPIO supportAlbert ARIBAUD \(3ADEV\)
This driver only supports Driver Model, not legacy model. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: i2c: add LPC32xx I2C interface supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: mtd: nand: add MLC NAND controllerAlbert ARIBAUD \(3ADEV\)
The controller's Reed-Solomon ECC hardware is used except of course for raw reads and writes. It covers in- and out-of-band data together. The SPL framework is supported. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add Ethernet supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10Merge branch 'u-boot/master'Albert ARIBAUD
2015-04-09ARM: mx5: add support for USB armory boardAndrej Rosano
Add support for Inverse Path USB armory board, an open source flash-drive sized computer based on Freescale i.MX53 SoC. http://inversepath.com/usbarmory Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Chris Kuethe <chris.kuethe@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-By: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-09ARM: mx5: move to a standard arch/board approachAndrej Rosano
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the commit: 89ebc82137bebb11a8191f8b9cbf08f2533ae8bc Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-07am33xx/ddr.c: Fix regression on DDR2 platformsTom Rini
Back in fc46bae a "clean up" was introduced that intended to reconcile some of the AM335x codepaths based on how AM43xx operates. Unfortunately this introduced a regression on the DDR2 platforms. This was un-noticed on DDR3 (everything except for Beaglebone White) as we had already populated sdram_config correctly in sequence. This change brings us back to the older behavior and is fine on all platforms. Tested on Beaglebone White, Beaglebone Black and AM335x GP EVM Reported-by: Matt Ranostay <mranostay@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-06dts: peach_pi: Add DT properties needed for displayAjay Kumar
Add backlight enable GPIO, and delay needed for panel powerup via FIMD DT node. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06dts: peach_pit: Add SLP and RST GPIO properties in parade DT nodeAjay Kumar
Now that parade driver supports reading SLP and RST GPIO from DT, specify the same in parade DT node. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06dts: exynos54xx: Add samsung, pwm-out-gpio property to FIMD nodeAjay Kumar
Now that the exynos_fb driver supports handling backlight GPIO via DT, specify pwm output property via FIMD DT node. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06Exynos5: Fix rpll_sdiv to support both peach-pit and peach-pi panelsAjay Kumar
The existing setting for rpll_sdiv generates 70.5Mhz RPLL video clock to drive 1366x768 panel on peach_pit. This clock rate is not sufficient to drive 1920x1080 panel on peach-pi. So, we adjust rpll_sdiv to 3 so that it generates 141Mhz pixel clock which can drive peach-pi LCD. This change doesn't break peach-pit LCD since 141/2=70.5Mhz, i.e FIMD divider at IP level will get set to 1(the required divider setting will be calculated and set by exynos_fimd_set_clock()) and hence peach-pit LCD still works fine. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06arm: exynos: add display clocks for Exynos5800Ajay Kumar
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5800 needed by exynos video driver. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06Exynos: Clock: Fix exynos5_get_periph_rate for I2C.Guillaume GARDET
Commit 2e82e9252695a612ab0cbf40fa0c7368515f6506 'Exynos: Clock: Cleanup soc_get_periph_rate' introduced a bug in I2C config. This patch makes cros_ec keyboard working again on Samsung Chromebook (snow). Changes in V2: reorder lines as requested by Joonyoung Shim. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Reviewed-by: Simon Glass <sjg@chroimum.org> Tested-by: Simon Glass <sjg@chroimum.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>