| Age | Commit message (Collapse) | Author |
|---|
|
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Update DDR IO register values.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
A generic is_dra72x cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Updating EMIF registers to enable HW leveling
on DRA72-evm.
Also updating the timing registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Updating EMIF registers to enable HW leveling
on DRA7-evm.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
Drop the code that doesn't use driver model for USB.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We plan to enable device tree in SPL by default. Before doing this,
explicitly disable it for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The 4KB padding doesn't seem necessary since we don't normally adjust the
control device tree file within U-Boot. Also drop the memory table space.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Support this function so we can use Chrome OS verified boot with sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is used before jumping to U-Boot, but in that case we don't
always want to disable caches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
Somehow this change was dropped in the various merges. I noticed when I
came to turn off the non-driver-model support for Tegra. We need to make
this change (and deal with any problems) before going further.
Change-Id: Ib9389a0d41008014eb0df0df98c27be65bc79ce6
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
|
|
|
|
This fixes ethernet no longer working on boards which use a gpio to enable
the phy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This commit cleanup MAX77686 regulator node by:
- remove the sub-nodes of unconnected regulators
- remove the "regulator-compatible" properties of all regulators
This prevents printing init errors for the regulators,
with duplicated name strings.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
With the rename the MAINTAINER file was not updated. Fix it and the
'Chrombook' typo in Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a hook to allows boards to add their own init to board_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
There are some missing entries in the tables. Add them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This is required in order to avoid instability when running from caches
after the kernel starts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
A harmless but confusing warning is displayed when looking up the
DisplayPort PLL. Correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a simple function to enable external clocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Enable the EC and keyboard, using the SPI bus.
The EC driver requires a particular format and a deactivation delay. Also
U-Boot does not support interrupts.
For now, adjust the device tree to comply. At some point we should tidy
this up to support interrupts and make tegra and exynos use the same setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
max_freq in print_cpuinfo is used only with
imx6.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Add IOMUX for the pad used as USB pen. This needs to be driven low for
the Iris and Viola boards where it is pulled up high by default. This is
required for the USB host functionality to work on these boards. Use the
board specific weak initialisation function, to drive the pin low which
would be called on "usb start".
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
|
|
Add device tree files for Freescale Vybrid platform and
Toradex Colibri VF50, VF61 modules.
Device tree files are taken from upstream Kernel.
Removed the stuff which are not used/supported yet in U-Boot.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
Add iomux definitions for DSPI second instance.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
Inorder to use the pins as GPIO, apart from setting the alt-function,
pinmuxing need to be done, this patch adds pinmux entries of
few GPIOs.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
Add GPIO driver support to Freescale VF610
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
|
|
Add and use a proper dts for the ga10h a33 based tablet, as
submitted upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
|
|
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2 ,
this gives us a proper dtsi file for the A33 rather then abusing
sun8i-a23.dtsi for this.
And this replaces our minimal (dummy) sun7i-a20-mk808c and
sun8i-a33-astar-mid756 dts files with proper ones.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been
using the same defconfig (and dts on the kernel side) for both models.
Unfortunately this does not work for the otg controller, on the M9 this
is routed to a micro-usb connector on the outside, while as on the
A1000G-quad it is connected to an usb to sata bridge.
This commit adds a new defconfig for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Before this commit the code for determining the disconnect threshold was
checking for sun4i or sun6i assuming that those where the exception and
that newer SoCs use a disconnect threshold of 2 like sun7i does.
But it turns out that newer SoCs actually use a disconnect threshold of 3
and sun5i and sun7i are the exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes for sun4i - sun7i, and
changes the disconnect threshold for sun8i to match what Allwinner uses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
