summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2017-01-18Merge git://git.denx.de/u-boot-samsungTom Rini
2017-01-18ARM: dts: exnyos4210-universl_c210: add i2c_5 and pmic nodesJaehoon Chung
Add the i2c_5 node and pmic as its child node. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-01-18ARM: dts: exynos4: use the node's name for i2cJaehoon Chung
Use the node's name for i2c. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-01-18board: samsung: goni: fix the pmic's name for gettingJaehoon Chung
For Getting from uclass, use the "max8998-pmic" as name. It also needs to change the dt-node's name as "max8998-pmic". Otherwise, it doesn't find the pmic device. Because it's only searching for 'max8998_pmic'. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-01-18ARM: uniphier: move SBC and Support Card init code to U-Boot properMasahiro Yamada
Initialize SBC and Support Card in U-Boot proper instead of SPL. We may run different firmware (ex. ARM Trusted Firmware) before U-Boot, and basic SoC initialization may be done there. In that case, SPL may not be used. The motivation for preparing SBC and Support Card in SPL was to use LED for early debugging, but this is not mandatory to boot SoCs. With this commit, LED will be unavailable in SPL, but we can use a debug serial instead. So, this change will not be a big deal. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18ARM: uniphier: refactor spl_init_board()Masahiro Yamada
Merge init-*.c into a single file using a table of callbacks because the initialization flow is almost common among SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18ARM: uniphier: refactor board_init()Masahiro Yamada
The code here is cluttered due to the switch statement. Introduce a table of callbacks to clean up the initialization code across SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: make BCU init into void functionMasahiro Yamada
These functions never fail, so no need to return a value. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: refactor Support Card init codeMasahiro Yamada
Splitting reset assertion (support_card_reset) and deassertion (support_card_init) is not adding much value any more. Handle all the initialization of Support Card in support_card_init(), then remove support_card_reset(). Also, detect_num_flash_banks() can have a static qualifier. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: refactor SBC init codeMasahiro Yamada
Merge sbc-admulti.c and sbc-savepin.c into a single file to avoid code duplication. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: refactor MEMCONF init codeMasahiro Yamada
Currently, memconf-sld3.c and memconf-pxs2.c duplicate the code. There are 3 patterns in terms of MEMCONF init: - DRAM 2 channels: LD4, sLD8, Pro4, Pro5, LD11 - DRAM 3 channels: sLD3 - DRAM 3 channels (Ch2 is disable by MEMCONF[21]): Pxs2, LD20 All of them can be moved into a single file by a little more refactoring. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: split out UMC clock enableMasahiro Yamada
The clock enable bits for UMC are more SoC-specific than for the other hardware blocks. Separate the UMC clocks and the other clocks for better code reuse across SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: uniphier: remove unneeded argument of uniphier_ld20_pll_init()Masahiro Yamada
At first, we thought the LD20 PLL setting would be board dependent, but this argument turned out unneeded after all. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17ARM: dts: uniphier: add UniPhier specific compatible to eMMC nodeMasahiro Yamada
The "cdns,sd4hc" is a fallback of the IP. Add the SoC-specific compatible string. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-15Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2017-01-15Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2017-01-15spi: Zap cf_qspi driver and related codeJagan Teki
Dropped becuase - driver not used any board. - no dm conversion. Cc: Angelo Dureghello <angelo@sysam.it> Cc: Richard Retanubun <richardretanubun@ruggedcom.com> Signed-off-by: Jagan Teki <jagan@openedev.com> Acked-by: Angelo Dureghello <angelo@sysam.it>
2017-01-15sunxi: dts: OrangePi Zero: add Ethernet nodeAndre Przywara
The OrangePi Zero can happily use the EMAC along with its integrated PHY to use Ethernet (for TFTP booting, for instance). Add the emac node to the board .dts by copying it from the OrangePi One DT. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-15sunxi: add proper device tree for Orange Pi Zero boardsIcenowy Zheng
Add a proper device tree file for Orange Pi Zero boards from Xunlong, which come with a Allwinner H2+ SoC (similar to H3). Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-15sunxi: enable H3 EMAC for the nanopi neoJelle van der Waa
The nanopi already had the CONFIG_SUN8I_EMAC=y enabled in it's defconfig file, but was missing the &emac the device tree entry. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-14davinci: spl: use bootcfg to select boot deviceFabien Parent
Right now the SPL is trying to load u-boot based on defines, i.e. one has to define CONFIG_SPL_NAND_SIMPLE to boot from NAND, or CONFIG_SPL_SPI_LOAD to boot from SPI FLASH, etc... This prevent us from having a single SPL image that is able to boot from all media, and one need to build an image for each medium. This commit is replacing the #ifdef that select the boot medium by reading the value of the boot pins (via the BOOTCFG register). Now a single SPL image will be able to read from the boot pin to know which device should be used to load u-boot. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-14armv8: fix #if around spin-table code in start.SOded Gabbay
Using CONFIG_IS_ENABLED() doesn't work in SPL. This patch replaces the only occurrence of CONFIG_IS_ENABLED() in start.S to a regular #if defined(). It also adds "&& !defined(CONFIG_SPL_BUILD)" to that #if statement because the spin-table code can't currently work in SPL, and the spin-table file isn't even compiled in SPL. Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
2017-01-14arm: omap-common: add secure ROM signature verify index for AM33xxAndrew F. Davis
On AM33xx devices the secure ROM uses a different call index for signature verification, the function and arguments are the same. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-01-14arm: Re-sync asm/mach-types.h with Linux Kernel v4.9Tom Rini
This re-syncs the MACH_TYPE_xxx values from the Linux Kernel v4.9 release. In addition this removes all of the machine_arch_type and machine_is_xxx logic that is unused in U-Boot. This removal removes a large number of otherwise unused CONFIG values from the list to be converted. Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Adam Ford <aford173@gmail.com>
2017-01-11rockchip: rk3288: set isp/vop qos priority levelNickey Yang Nickey Yang
Isp-camera preview image will be broken when dual screen display mode. This patch set isp/vop qos level higher to solve this problem. We have verified this patch on rk3288-miniarm board. Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
2017-01-11arm64: rk3399: update rockchip_get_cru APIKever Yang
rk3399 has two clock-controller: cru and pmucru, update the rockchip_get_crui() API, and rockchip_get_clk() do not used for other module. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-01-11dts: arm64: rk3399: add max-frequency for sdhciKever Yang
Add 'max-frequency' for sdhci node for clock init. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11rockchip: Fix veyron-minnie's Kconfig descriptionMartin Michlmayr
The veyron-minnie Kconfig referred to jerry by mistake. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Simon Glass <sjg@chromium.org>
2017-01-11rockchip: dts: popmetal: add usb host power supply nodeKever Yang
The popmetal board using a HOST_VBUS_DRV gpio signal to control the USB host port 5V power, add a fix regulator and pinctrl for it, and enable the USB host1 controller with the vbus-supply. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-11SPL: Adjust more debug prints for ulong entry_pointTom Rini
With entry_point now being an unsigned long we need to adapt the last two debug prints to use %lX not %X. Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-11Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2017.03 - ATF handoff - DT syncups - gem: Use wait_for_bit(), add simple clk support - Simple clk driver for ZynqMP - Other small changes
2017-01-11mmc: move more driver config options to KconfigMasahiro Yamada
Move (and rename) the following CONFIG options to Kconfig: CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI) CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS) CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC) CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS) CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA) CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI) They are the same option names as used in Linux. This commit was created as follows: [1] Rename the options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g ' [2] Commit the changes [3] Create entries in driver/mmc/Kconfig. (copied from Linux) [4] Move the options with the following command tools/moveconfig.py -y -r HEAD \ MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI [5] Sort and align drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-10Merge git://git.denx.de/u-boot-dmTom Rini
2017-01-10mips: Use common _AC macro now.Tom Rini
MIPS no longer needs to have its own version of this macro now. Fixes: 2a6713b09b8d ("move UL() macro from armv8/mmu.h into common.h") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-10Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2017-01-10ARM64: zynqmp: Generate handoff structure for ATFMichal Simek
Xilinx ATF extending options for passing images from BL2(FSBL) to BL31. U-Boot SPL is FSBL replacement that's why it should generate handoff structure the same. Support only one entry which is U-Boot in EL2 itself. When FIT image is adopted structure generate should be data driven. Currently ATF is placing this structure at the beggining of OCM which is rewriting early parts of ATF which should be unused at that time. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynqmp: Make SYS_VENDOR configurableMike Looijmans
Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Fix i2c node's compatible stringMoritz Fischer
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core which fixes some silicon bugs that needed software workarounds in Version 1.0 that was used on Zynq systems. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10net: zynq_gem: Use clock driver for ZynqMPSiva Durga Prasad Paladugu
Enable and use the clock driver routine defined in clock driver toset required clock appropriately. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Add idle state for ZynqMPStefan Krsmanovic
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0 idle state is added in this patch. References to the idle-states node are added in all CPU nodes. Time values: entry/exit latencies and min-residency, needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0 and Extended StateID format. Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: Will Wong <willw@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Fix usb nodes for dc1 and dc2Michal Simek
Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Add missing earlycon for ep108Michal Simek
Just sync between version. Others zynqmp boards have this setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-10ARM64: zynqmp: clk: Add the clock for watchdogShubhrajyoti Datta
The watchdog clock node is missing. Add the same. This solves the below error. cdns-wdt fd4d0000.watchdog: input clock not found cdns-wdt: probe of fd4d0000.watchdog failed with error -2 Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source propertySudeep Holla
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynq: Remove spi-max-frequencyMichal Simek
spi-max-frequency for spi bus depends on devices which are connected to it. Remove this parameter from dtsi file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-09am33xx: board: init usb ether gadget for rndis supportMugunthan V N
Add usb ether gadget device with usb_ether_init() when CONFIG_DM_ETH and CONFIG_USB_ETHER are defined. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-08am335x: configs: Use ISW_ENTRY_ADDR to set SPL_TEXT_BASEAndrew F. Davis
The SPL load address changes based on boot type in HS devices, ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs for similar reasons. Add this same logic for AM33xx devices. Also make the default value for ISW_ENTRY_ADDR correct for GP devices based on SoC, HS devices already pick the correct value in their defconfig. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-01-08arm: mach-omap2: Fix secure file generationAndrew F. Davis
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was not generated but generate an unsigned one anyway, first fix this warning to say that it was generated but not secured. When the user then exports TI_SECURE_DEV_PKG after getting this warning, and tries to re-build, 'make' will detect the build artifacts as unchanged and so assume they do not need to be re-generated. This causes it to fail to sign the files and it will pack unsigned files into the final image, even though TI_SECURE_DEV_PKG is now correctly defined and working. Fix this by using FORCE on the targets causes them to be re-run even if the dependent files have not changed. This then causes another issue. We currently rename the signed dtb files to overwrite the non-signed ones. We do this so the 'mkimage' tool gives the packaged dtb sections the correct name. If we do not rename the files then SPL will not find them during boot. Fix this by renaming the dtb files by appending _HS to the end of the filename, after the ".dtb", this causes them to still be named correctly in the FIT blob. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-01-04Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2017-01-04powerpc: mpc85xx: Move macro CONFIG_SYS_PPC64 to KconfigYork Sun
Use Kconfig option SYS_PPC64 instead. Signed-off-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-25 17:15:12 +0000