| Age | Commit message (Collapse) | Author |
|---|
|
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Fix VI_I2C clock source type. Will be needed by VI_I2C driver.
Also added use of INTERNAL_ID macro in two places, needed to keep
the id returned to 8 bits.
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.
Adds call to board_cleanup_before_linux to facilitate this.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
Enable pre console buffer for rk3399 platform.
This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3399
platform boards.
Buffer address used for pre console is 0x0f200000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
|
|
VOP display endpoint pipeline configuration differs
between rk3288 vs rk3399.
These VOP pipeline configuration depends on how the
different display interfaces connected in sequence to
IN and OUT ports like for,
RK3288:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_hdmi: endpoint@1 {
reg = <1>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_lvds: endpoint@2 {
reg = <2>;
remote-endpoint = <&lvds_in_vopb>;
};
vopb_out_mipi: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi_in_vopb>;
};
};
RK3399:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_mipi: endpoint@1 {
reg = <1>;
remote-endpoint = <&mipi_in_vopb>;
};
vopb_out_hdmi: endpoint@2 {
reg = <2>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_mipi1: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi1_in_vopb>;
};
vopb_out_dp: endpoint@4 {
reg = <4>;
remote-endpoint = <&dp_in_vopb>;
};
};
here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399.
The rockchip vop driver often depends on this determined endpoint
number and stored in vop_mode. So based on this vop_mode the bpp
and pin polarity would configure on detected display interface.
Since, the existing driver using rk3288 vop mode settings enabling
the same will result wrong display interface configuration for rk3399.
Add the patch for fixing these vop modes for rk3399.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
|
|
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Add PHY reset GPIO on AV96 ethernet PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
|
|
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
|
|
The eMMC uses different pinmux for the top four data lines, use such
a pinmux, otherwise it takes a very long time until the test for 8bit
operation times out. And this is the correct pinmux per schematic too.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch and enable SDR104 operation.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The sdmmc1_dir_pins_a: sdmmc1-dir-0 layout changed in commit 35a54d41d9d4
("ARM: dts: stm32mp1: sync device tree with v5.2-rc4") such that pins{};
became pins1{};pins2{};, however the SPL extras were not updated to reflect
that change. Fix this.
This fixes booting from SD1 X9 slot on the AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 35a54d41d9d4 ("ARM: dts: stm32mp1: sync device tree with v5.2-rc4")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-arc
This last minute pull-request is intended to fix some drivers
when used on ARC boards. The problem was introduced by
https://gitlab.denx.de/u-boot/u-boot/-/commit/07906b3dad157bd58411664bcc6a2a7976d5e0a9
What happened while doing one pretty simple improvement to make
U-Boot port more flexible and portable (by switching accessors from
assembly-written to plain C version) we implicitly added 2 problems:
1. Downgraded accessors from being volatile which signalled to
the compiler that it's now possible to do all kinds of optimizations
which may easily include merge of subsequent byte reads/writes into
word operations. Which is OK for accessing mormal memory but
breaks operation of peripherals if we access its memory-mapped regs
in such a "creative" manner.
2. As a part of assembly-written implementation we had compiler barriers
in form of the following construction 'asm volatile("" : : : "memory")',
and we dropped it in C implemntation. This in its turn enabled compiler
to mess with instruction ordering. Guess what it gives us in the end :)
So with all that we had in some corner-cases veeery funny instruction flows
generated. And in particular it broke DW SPI functionality when we were
writing large amount of data. Funny enough our tests which were writing
small amount of data still worked and only by the chance we caught that
breakage and unrolled that quite interesting loop of unexpected
problems.
The road to hell is paved with good intentions. Amen :)
|
|
We add memory barriers for __raw_readX / __raw_writeX accessors same
way as it is done for readX and writeX accessors as lots of U-boot
driver uses __raw_readX / __raw_writeX instead of proper accessor
with barrier.
It will save us from lot's of debugging in the future and it is OK
as U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not
super fast as we only being executed once.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
We must use compiler barriers in C-version read/write IO accessors
before and after operation (read or write) so it won't be reordered
by compiler.
Fixes commit 07906b3dad15 ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
We must use 'volatile' in C-version read/write IO accessors
implementation to avoid merging several reads (writes) into
one read (write), or optimizing them out by compiler.
Fixes commit 07906b3dad15 ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
- mpc8xxx GPIO, SPI bugfixes
- Add VxWorks to FIT images
- macb ethernet driver bugfix
|
|
Prepare for supporting setting different speeds in mpc8xxx_spi.c.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
|
|
|
|
- Fixes for Gen 2 V2H Blanche
|
|
Enable QSPI for Agilex SoC devkit.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add save_boot_params() to save reset status value from bootrom.
Bootrom will clear the status register in reset manager and stores the
reset status value in shared memory. Bootrom stores shared data at last
2KB of onchip RAM.
This function save reset status provided by bootrom to rst_mgr_status.
More information about reset status register value can be found in reset
manager register description.
When running in debugger without bootrom, r0 to r3 are random values.
So, skip save the value when r0 is not bootrom shared data address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add OCRAM size macro for Gen5 and Arria 10.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
- Fixes env variable for layerscape platforms, disable hs200.
- Fixes board fixup, mux setting, enable gic, fspi on lx2160a, Fixes I2C
DM Warning on ls1043a, ls1046a
- Fixes RGMII port on ls1046ardb, ls1046ardb and DM_USB Warning on
ls1012afrdm, ls1021aiot
|
|
- SPL SPI support R40, H6 (Andre)
- eMMC boot part on a64-olinuxino (Petr)
|
|
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Enable IIC3 to permit access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Since commit 79030a486128 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot.
-Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This path allows to set the cntfrq register of targeted cpu.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
