| Age | Commit message (Collapse) | Author |
|---|
|
commit 20f14714169 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
|
|
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Enable sdmmc node in SPL and add it to boot order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tags:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
Since commit 999a78d5cf00 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110")
dtc warns about:
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000
Fix this by adding a node for the tzic interrupt controller.
Copied from "<Linux>/arch/arm/boot/dts/imx53.dts"
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:
In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2
Add HAS_CAAM configuration to avoid this error.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
MX6UL contains features that MX6ULL doesn't support.
Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS.
The motivation for doing this change is that MX6UL supports CAAM and
MX6ULL does not.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
"ethernet" node fix-up for device tree happens before Linux boot.
There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
FLIS IP since now gets its own ACPI ID.
Drop PRP0001 workaround in favour of official ACPI HID.
Corresponding kernel commit dabd4bc6de2b
pinctrl: intel: merrifield: Introduce ACPI device table
in the pin control subsystem tree [1] targeting v4.16.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=dabd4bc6de2b
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
|
|
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
|
|
|
|
Using writel causes a "Synchronous Abort". Invert the arguments.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
|
|
Update README file to note LS2088A and LS1088A don't support booting
from NAND flash.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Rockchip release bl31.elf file for armv8 SoCs like rk3399, rk3328,
the elf have more than one section, we need to decode it first and
packed them into u-boot.itb with its file. This script is to generate
the its script.
Need default bl31.elf in root directory of U-Boot source and dtb
as parameter.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Only rk3399 atf need ROCKCHIP_SPL_RESERVE_IRAM. This commit updates
its default setting to 0 so that other SoCs do not need to define it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.
The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.
Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The efi linker script includes sections needed for the dynamic linker.
However, in our EFI application environment we don't have a dynamic linker.
So let's remove them. That way we save on 4k padding and reduce the file
size of the hello world efi binary from ~4k to ~1k.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
|
|
Add missing zynq_board_read_rom_ethaddr() prototype reported by sparse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This is the same patch as was done earlier.
Please look at Linux patch:
"arm64: zynqmp: Use only earlycon bootargs instead of full one"
(sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable USB3.0 and SATA phy for zcu102 boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Setup proper dependency in Kconfig for SPL_CLK.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This reference is needed for pinctrl driver where some signals can be
routed directly to platform management unit (PMU).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
|
|
Using "cpu_pos_mask()" function to detect the real online cpus,
and discard the needless cpu nodes on kernel dts.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This area of the image contains symbols whose values are filled in by
binman. If this feature is not used, the table is empty.
Add this to the ARM SPL link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
And use 'imply' liberally.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
