| Age | Commit message (Collapse) | Author |
|---|
|
Synchronize Altera Arria 10 DT sources with Linux 4.16.3 as of commit
ef8216d28a5920022cddcb694d2d75bd1f0035ca
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
Sort the Makefile entries, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
The A10 clock manager parsed DT bindings generated by Quartus the
bsp-editor to configure the A10 clocks. Sadly, those DT bindings
changed at some point. The clock manager patch used the old ones,
this patch replaces the bindings parser with one for the new set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
Pull the serial port configuration from DT and use DM serial instead
of having the serial configuration in two places, DT and board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
Shuffle the default Kconfig entries around so it is not such a mess.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
This was never used, is not used anywhere and is just in the way
by adding annoying ifdeffery. Get rid of it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
This commit adds support for DDC and HSC boards from
K+P in u-boot.
Console output:
U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: WDOG
Model: K+P iMX53
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Module EEPROM:
ID: TQMa53-CB.0401
SN: 63152762
MAC: 00:0b:64:03:14:2a
BBoard:40x0 Rev:10
Net: eth0: ethernet@63fec000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit also provides the default values of the emulated MC34708 PMIC
internal registers content.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
MX6DL Mamoj boards has Freescale PFUZE100 PMIC, add support
for it through DM_PMIC dt definition.
pmic log:
Reviewed-by: Stefano Babic <sbabic@denx.de>
========
=> pmic list
| Name | Parent name | Parent uclass @ seq
| pfuze100@08 | i2c@021f8000 | i2c @ 3
=> pmic dev pfuze100@08
dev: 0 @ pfuze100@08
=> pmic dump
Dump pmic: pfuze100@08 registers
0x00: 10 00 00 21 00 01 3f 01 00 7f 00 00 00 00 00 81
0x10: 00 00 3f 00 00 00 00 00 00 00 00 10 00 00 00 00
0x20: 2b 2b 2b 08 c4 00 00 00 00 00 00 00 00 00 2b 2b
0x30: 2b 08 c4 00 00 72 72 72 08 d4 00 00 2c 2c 2c 08
0x40: e4 00 00 2c 2c 2c 08 e4 00 00 6f 6f 6f 08 f4 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 48 00 00 00 10 06 1e 1e 17 10
0x70: 1a 1f 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
i.MX6DL Mamoj has i2c3 and i2c4 buses, add support
through DM_I2C with dt definition.
i2c log:
Reviewed-by: Stefano Babic <sbabic@denx.de>
=======
=> i2c bus
Bus 2: i2c@021a8000
Bus 3: i2c@021f8000
=> i2c dev 2
Setting bus to 2
=> i2c speed 400000
Setting bus speed to 400000 Hz
=> i2c probe
Valid chip addresses: 20 51 53
=> i2c md 53 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
=> i2c md 51 0xff
00ff: a8 08 40 50 09 43 46 52 42 18 80 8e ae a9 d0 53 ..@P.CFRB......S
=> i2c dev 3
Setting bus to 3
=> i2c speed 100000
Setting bus speed to 100000 Hz
=> i2c probe
Valid chip addresses: 08 40 48 4B
=> i2c md 08 0xff
00ff: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
Add initial support for i.MX6DL BTicino Mamoj board.
Mamoh board added:
- SPL
- SPL_DM
- SPL_OF_CONTROL
- DM for U-Boot proper
- OF_CONTROL for U-Boot proper
- eMMC
- FEC
- Boot from eMMC
- Boot from USB SDP
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Build dtb's based on SOC type instead building arch type.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6UL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Move usdhc2 node along with pinctrl to imx6ul-isiot.dts
from imx6ul-isiot-emmc.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6QDL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Import the dts files from Linux 4.17 and enable device tree control in
u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
These files are taken verbatim from the Linux kernel 4.17
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The SION pin must be set for proper operation of I2C when DM is enabled.
When legacy I2C is used, this bit is set implicitly in the u-boot code:
arch/arm/include/asm/arch-mx5/iomux-mx53.h:92:
MX53_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x368, 0x040, 4 |
IOMUX_CONFIG_SION, 0x820, 0, NO_PAD_CTRL),
The Linux kernel uses similar approach with:
arch/arm/boot/dts/imx53-tqma53.dtsi:182:
MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000
After applying this patch it is possible to have the I2C working with DM
on imx53 devices:
MX53_PAD_KEY_ROW3__I2C2_SDA (0x1ee | IMX_PAD_SION)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Those DTS nodes has been ported from Linux kernel (v4.16)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
It makes sense to select the MP multi processor option at the same time we
select the other SMP options needed for SMP capable i.MX6 SoCs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
|
|
Also remove the #ifdef's from clock.h since the Kconfig values defaults
the to old default values in clock.h.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
nds2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nds32 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
|
|
nds32 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nds32
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
|
|
nios2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nios2 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
|
|
nios2 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nios2
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
|
|
riscv bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
riscv bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
riscv bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
x86 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
Add PWM definition to sun50i-a64.dtsi
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
|
|
This commit adds basic support for PWM found on Allwinner A64.
It can be used for pwm_backlight driver (e.g. for Pinebook)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
|
|
Add Kconfig for MVGBE and update boards to select this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Move sys_env_device_rev_get() from the ddr training code to
sys_env_lib.c (which currently resides with the serdes code). This
brings sys_env_device_rev_get() into line with sys_env_device_id_get()
and sys_env_model_get().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
PEX_CFG_DIRECT_ACCESS was defined in ddr3_hws_hw_training_def.h despite
only being used in the serdes code. Move this definition to ctrl_pex.h
where all the other PEX defines are. Also remove the duplicate
definition of PEX_DEVICE_AND_VENDOR_ID which is already defined in
ctrl_pex.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This adds support for the CPU watchdog found on Marvell Armada 37xx
SoCs.
There are 4 counters which can be set as CPU watchdog counters.
This driver uses the second counter (ID 1, counting from 0)
(Marvell's Linux also uses second counter by default).
In the future it could be adapted to use other counters, with
definition in the device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.
Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The drivers are based on Linux driver by Gregory Clement.
The TBG clocks support only the .get_rate method.
- since setting rate is not supported, the driver computes the rates
when probing and so subsequent calls to the .get_rate method do not
read the corresponding registers again
The peripheral clocks support methods .get_rate, .enable and .disable.
- the .set_parent method theoretically could be supported on some clocks
(the parent would have to be one of the TBG clocks)
- the .set_rate method would have to try all the divider values to find
the best approximation of a given rate, and it doesn't seem like
this should be needed in U-Boot, therefore not implemented
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
