| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Remove blackfin specific implementation of the generic serial API when
early print macro is defined.
In BFIN_BOOT_BYPASS mode, don't call generic serial_puts, because
early print in bypass mode is running before code binary is relocated
to the link address.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Add softswitch_output command for bf609-ezkit to enable softswitches.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
The early serial should not be configured again in initcode() for BYPASS
boot mode and in start() for the other LDR boot modes.
In BYPASS boot mode, the start up code is located in Nor flash address other
than the DRAM address defined in link script. The code embedded string can't
be addressed by its compile time symbol. Calculate it according to the flash
offset.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Calculate the early uart clock from the system clock registers set by
the bootrom other than the predefine uboot clock macros.
Split the early baudrate setting function and the normal baudrate
setting one.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Define core 1 L1 code sram start address.
Add function to enable core 1 for BF609 and BF561.
Add config macro to allow customer to run core 1 in uboot init code on core 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Newer gcc versions will sometimes use a Preg when "r" constraints, but
that'll fail if we use an Ireg in the assignment. So force the code
to always use a Dreg.
This also fixes early boot crashes for older Blackfin parts when compiled
with gcc-4.5. This version ends up selecting the same register for the
input and output variables which corrupts the output assignment triggering
an exception.
P2 = 0xffe02008; /* EVT2 */
R0 = RETS;
CALL 1f;
RTN;
1: P2 = RETS; <-- BAD
RETS = R0;
[P2] = P2; <-- BAD
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Othersize, the bf609 memory dma halts after being enabled.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Unifies the openrisc boards linker scripts into a common one.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
|
|
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
fdt_initrd add additional information to DTB about initrd
addresses which are later used by kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Prepare place for new patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Include this header to get access to link symbols, which are otherwise
removed.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
|
|
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
cpu.c:288:2:
warning: implicit declaration of function 'reset_85xx_watchdog'
[-Wimplicit-function-declaration]
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
For T4/B4, the clockgen node compatible string is updated to version 2.
Add clock-frequency setting for this new version.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
B4420/B4860 PCIE can not work because of the wrong definition of
the PCIE register offset in the file:
arch/powerpc/include/asm/immap_85xx.h
Add the judgement of B4420/B4860 to make the register offset to:
#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Set the device tree property associated with the mpic source
frequency. The frequency is used for mpic timer.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.
Also removed unnecessary static global variables.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
|
The prt_mpc512x_clks() function isn't referenced
anywhere and its prototype is wrong. Remove it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Make nios2's board.c checkpatch clean.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Make microblaze's board.c checkpatch clean.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
|
|
This allows passing of entire scripts to sandbox with the -c argument,
which is useful for testing. Commands can be delimited with a newline
or semicolon.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
In many cases, pointers to memory are passed around, and these pointers
refer to U-Boot memory, not host memory. This in itself is not a
problem.
However, in a few places, we cast that pointer back to a ulong (being
a U-Boot memory address). It is possible to convert many of these cases
to avoid this. However there are data structures (e.g. struct
bootm_headers) which use pointers. We could with a lot of effort adjust
the structs and all code that uses them to use ulong instead of pointers.
This seems like an unacceptable cost, since our objective with sandbox
is to minimise the impact on U-Boot code while maximising the features
available to sandbox.
Therefore, create a map_to_sysmem() function which converts from a
pointer to a U-Boot address. This can be used sparingly when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
This patch adds SPL booting support (NOR flash) for the
PPC4xx platforms.
This SPL booting (Falcon mode) will be used by the upcoming
lcd4_lwmon5 board port (lwmon5 variant).
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Quick manual fixup to merge the USB boot related defines and TPM related
defines.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The current code is causing errors like this on my toolchains:
/usr/x86_64-pc-linux-gnu/armv7a-cros-linux-gnueabi/binutils-bin/2.22/
ld.bfd.real: failed to merge target specific data of file /usr/lib/gcc/
armv7a-cros-linux-gnueabi/4.7.x-google/libgcc.a(_divdi3.o)
Use do_div() to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
The intention of the memory init code is that it should work the same with
CONFIG_SYS_GENERIC_BOARD and without. This is tricky because dram_init()
is called prior to relocation with generic board (matching other archs)
and after relocation without generic board.
Adjust the init sequence so that dram_init() is not called in the generic
board case, which seems like the easiest fix for now. Also ensure that
relocation addresses are still calculated.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
A comparison of registers between our internal NV U-Boot and
u-boot-tegra/next showed some discrepancies in the MSELECT
clock divisor programming. T20 doesn't have a MSELECT clk src reg.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
T114 needs the SYSCTR0 counter initialized so the TSC can be
read by the kernel. Do it in the bootloader since it's a write-once
deal (secure/non-secure mode dependent).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
Without this change, kernel fails at calling function cache_clean_flush
during kernel early boot.
Aprocryphally, intended for T114 only, so I check for a T114 SoC.
Works (i.e. dalmore 3.8 kernel now starts printing to console).
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
A start vector fix was added by AneeshV for OMAP4 (commit 0d479b53),
and caused the old monilithic Tegra builds to hang due to an undefined
instruction trap. Previously, the code needed to run on both the
AVP (ARM7TDI) and A9, and the AVP doesn't have a CP15 register.
I corrected this in commit 6d6c0bae w/#ifndef CONFIG_TEGRA, but
now that we use SPL, and boot the AVP w/o any ARMv7 code, I can
revert my change, and make Aneesh's change apply to Tegra.
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically
to any other Tegra30.
An alternative would be to simply remove the SKU checking from
tegra_get_chip_type(); most use of the value most likely simply wants
to know the current chip, not the specific SKU. Or, the function could
be split into separate tegra_get_chip() and tegra_get_sku() for the
cases where differentiation really is required.
I wonder whether tegra_get_chip_type() should printf() whenever any
unkown chip/SKU is found, although perhaps the function is called so
early that the printf() wouldn't actually make it to the UART anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
