summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2019-01-28arm: dts: imx7s-warp: Import Linux warp7 dtsBryan O'Donoghue
This patch imports the Linux kernel warp7 dts as at upstream kernel commit cf76c364a1e1. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28arm: dts: imx7: Correct spelling mistake in GPIO nameBryan O'Donoghue
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once corrected we can import the latest kernel DTS unmodified. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-01-28imx8: cpu: restrict checking ROM passover info for revAPeng Fan
Passover info only for revA. move get_cpu_rev out of CONFIG_CPU to avoid build failure when using get_cpu_rev in SPL. Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again in normal U-Boot stage. Also if still checking passover info in normal U-Boot stage, need to make the passover code executed after arch_cpu_init_dm. So to make it easy and clean, only execute the code for SPL stage. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: Check the PL310 version for applying errataYe Li
Apply errata based on PL310 version instead of compile time. Also set Prefetch offset to 15, since it improves memcpy performance by 35%. Don't enable Incr double Linefill enable since it adversely affects memcpy performance by about 32MB/s and reads by 90MB/s. Tested with 4K to 16MB sized src and dst aligned buffer. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Ye Li <ye.li@nxp.com>
2019-01-28ARM: imx: fix: Provide correct enum values for ONENAND/NOR boot recognitionLukasz Majewski
According to "Table 5-1. Boot Device Select" (page 335, i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017) the BOOT_CFG1[3] have following values (regarding EIM booting): 0 - NOR flash and 1 - ONENAND This commit provides correct identification of the boot medium for IMX6Q boards booting from NOR memory (MCCMON6 is one of them). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-28dm: arm: imx: migrate cx9020 to CONFIG_DM_MMCPatrick Bruenn
Enable esdhc1/2 device nodes for cx9020 and build with CONFIG_DM_MMC=y Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28arm: imx: Add esdhc1/2 nodes to imx53.dtsiPatrick Bruenn
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y They are copied from Linux 4.20 Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28imx: Fix potential lmb memory overwritten by stackYe Li
At default, u-boot reserves the memory from SP - 4KB to DRAM end for lmb in arch_lmb_reserve. So lmb won't allocate any memory from it. But we found the 4K gap for SP is not enough now, because some FDT updating operations are added in our u-boot before jumping to kernel, which needs larger stack. This causes the lmb allocated memory is overwritten by stack. Fix the issue by implementing the board_lmb_reserve to reserve from SP - 16KB to memory end for lmb. Signed-off-by: Ye Li <ye.li@nxp.com>
2019-01-28imx: build flash.bin for i.MX8Peng Fan
Build flash.bin for i.MX8 when SPL enabled. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: mkimage_fit_atf: introduce BL33_BASE_ADDRPeng Fan
Introduce BL33_BASE_ADDR, then we could reuse this script for i.MX8QXP. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28dts: imx8qxp-mek: introduce u-boot dtsiPeng Fan
Introduce u-boot dtsi for i.MX8QXP MEK board. we do not introduce a common dtsi for SoC, because different board has different requirement on which needs to be enabled in SPL DM. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28spl: imx8: add spl boot devicePeng Fan
Add spl_boot_device for i.MX8, also add BOOT_DEVICE_MMC2_2 for spl_boot_mode. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28arm: imx: build mach-imx for i.MX8Peng Fan
To enable SPL for i.MX8, we could reuse code in arch/arm/mach-imx. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8: scu: use dedicated MU for SPLPeng Fan
SPL runs in EL3 mode, except MU0_A, others are not powered on, and could not be used. However normal U-Boot use MU1_A, so we could not reuse the one in dts. And we could not replace the one in dts with MU0_A, because MU0_A is reserved in secure world. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8qxp: add SUPPORT_SPL optionPeng Fan
Enable SUPPORT_SPL option for i.MX8QXP, then we could enable SPL. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28arm: dts: imx7: colibri: add usdhci peripherals to device treeStefan Agner
Add usdhci peripherals to device tree. This allows to use DM_MMC for Colibri iMX7 devices. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2019-01-28arm: dts: imx7: colibri: split dt for raw NAND and eMMC devicesStefan Agner
In preparation of adding CONFIG_DM_MMC support use separate device trees for raw NAND and eMMC devices. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-01-28mx7: Do not call lcdif_power_down() in the SPL caseFabio Estevam
Like it was done on imx6 in commit 9236269de57d ("imx: mx6: Fix implementantion reset_misc") Do not call lcdif_power_down() in the SPL case to fix the following build error: LD spl/u-boot-spl MKIMAGE u-boot.img arch/arm/mach-imx/built-in.o: In function `reset_misc': /home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down' scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx: Add PHYTEC phyBOARD-i.MX6UL-SeginMartyn Welch
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063). CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Board: PHYTEC phyCORE-i.MX6UL I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC0 Working: - Eth0 - i2C - MMC/SD - NAND - UART (1 & 5) - USB (host & otg) Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-01-28imx: hab: Convert non-NULL IVT DCD pointer warning to an errorBreno Matheus Lima
The following NXP application notes and manual recommend to ensure the IVT DCD pointer is Null prior to calling HAB API authenticate_image() function: - AN12263: HABv4 RVT Guidelines and Recommendations - AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using HABv4 - CST docs: High Assurance Boot Version 4 Application Programming Interface Reference Manual Commit ca89df7dd46f ("imx: hab: Convert DCD non-NULL error to warning") converted DCD non-NULL error to warning due to the lack of documentation at the time of first patch submission. We have warned U-Boot users since v2018.03, and it makes sense now to follow the NXP recommendation to ensure the IVT DCD pointer is Null. DCD commands should only be present in the initial boot image loaded by the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error if a DCD pointer is present in an image being authenticated by calling the HAB RVT API. Older versions of HAB will process and run DCD if it is present, and this could lead to an incorrect authentication boot flow. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-01-24Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-01-24Merge tag 'mpc85xx-for-v2019.04-rc1' of git://git.denx.de/u-boot-mpc85xxTom Rini
mpc85xx config.mk: Add support for -msingle-pic-base
2019-01-24ARM: zynq: Remove unused GEM addressesMichal Simek
With DM in place there is no need to have GEM addresses in headers. None is using them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Remove unused GEM addressesMichal Simek
With DM in place there is no need to have GEM addresses in headers. None is using them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24zynq: Kconfig: extend the bootstrap malloc() poolAnton Gerasimov
Most of the memory is being consumed by device binding code, more space needed for other data structures. Z-turn board has already hit the limit, others may follow soon. Measuring only the memory consumed in device_bind_common, I've got the following results (in decimal): root_driver: 108 mod_exp_sw: 108 amba: 120 serial@e0000000 aka uart0: 112 serial@e0001000 aka uart1: 88 spi@e000d000 aka qspi: 120 sdhci@e0100000 aka mmc0: 455 sdhci@e0100000.blk: 208 slcr@f8000000: 96 clkc@100: 72 (total) 1487 = 0x5cf of 0x600 Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24topic-miamiplus: Run CPU at 800MHz for speedgrade-2Mike Looijmans
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz. Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Move SoC sources to mach-zynqmpMichal Simek
Similar changes was done for Zynq in past and this patch just follow this pattern to separate cpu code from SoC code. Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/* And also fix references to these files. Based on "ARM: zynq: move SoC sources to mach-zynq" (sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup proper SPI dependencyMichal Simek
Select DM_SPI/DM_SPI_FLASH for the whole SoC. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24ARM: zynqmp_r5: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: versal: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Fix mmc node names to be in sync with kernelSiva Durga Prasad Paladugu
This patches renames sd nodes in dts to be in line with kernel. This patch also modifies the references for the same in code. It checks mmc first to have no time penalty for new DT node names based on left-to-right expression evaluation. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Do not protect zynqmp_pmufw_version()Michal Simek
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version() but also FPGA code is calling this function which is possible to use without actual CLK_ZYNQMP firmware driver to be enabled. This patch enables the case where only fixed-clock CLK setup is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-23mpc85xx: Add support for -msingle-pic-baseJoakim Tjernlund
-msingle-pic-base is a new gcc(from 4.6) option for ppc and it reduces the size of my u-boot with about 4-5 KB. While at it, add -fno-jump-tables too to save a few more bytes. e5500 core: size u-boot.bef text data bss dec hex filename 473043 23772 307104 803919 c444f u-boot.bef size u-boot.aft text data bss dec hex filename 453195 23772 307104 784071 bf6c7 u-boot.aft e500 core: size u-boot.bef text data bss dec hex filename 292998 17868 24968 335834 51fda u-boot.bef size u-boot.aft text data bss dec hex filename 288002 17868 24968 330838 50c56 u-boot.aft Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-23MSCC: Add board support for Serval SoC family.Horatiu Vultur
Add board support and configuration for Jaguar2 SoC family. The detection of the board type is based on the phy ids. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-23MSCC: Add device tree for Serval pcb106 boardHoratiu Vultur
Add device tree based on evaluation board pcb106. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-23MSCC: add device tree for Serval pcb105 boardHoratiu Vultur
Add device tree based on evaluation board pcb105. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-23MSCC: Add support for Serval SoC family.Horatiu Vultur
As Ocelot, Servalt, Luton and Jaguar2, this family of SoCs are found in Microsemi Switches solution. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-23MSCC: Add board support for Servalt SoC familyHoratiu Vultur
Add board support, configuration and DTS for Servalt SoC family. Currently there is one board in this family. Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-23MSCC: Add support for Servalt SoC family.Horatiu Vultur
As Ocelot, Luton and Jaguar2, this family of SoCs are found in Microsemi Switches solution. Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-23MIPS: mscc: ocelot: Add ethernet nodes for OcelotGregory CLEMENT
Import Ethernet related nodes from Linux Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2019-01-22nds32: dts: Fix mmc node compatible stringRick Chen
In the two commits: cf3922dddc44a968685b535f2af195f1e51f4a7b mmc: ftsdc010_mci: Sync compatible with DT mmc node c14e90e8445e7b1c3531b4bdeb778c47bd6570eb riscv: dts: Sync DT with Linux Kernel ftsdc010_mci's compatible has been modified as "andestech,atfsdc010" for RISC-V synchronization. But ae3xx.dts and ag101p.dts which are used for nds32 adp-ae3xx and adp-ag101p platforms did not be modified correctly at that time. It will cause mmc detection failure. Fix it here. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
2019-01-22nds32: Fix boot fail issue when build with elf-mculib.Rick Chen
Add -mcmodel=large can let elf-mculib have the same default behavior just like linux-glibc. And it help to pass U-Boot booting sequence. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
2019-01-22nds32: Generate SW fpu instruction.Rick Chen
Force it to generate SW fup instruction. It help to avoid bugs when running on no-HW-fpu board, but compile with v3f which support HW fpu instruction. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
2019-01-22nds32: Remove gcc unused optionRick Chen
-G0 is an old option, not support now, So remove it. It can help to fix compile error when build with nds32 pre-build toolchain. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
2019-01-21Merge git://git.denx.de/u-boot-marvellTom Rini
- Sync Armada-38x dts with Linux 4.20 from Chris - Misc changes and enhancements to Turris Mox (v4) from Marek - Reserve PSCI area for Armada 8k from Heinrich - New Allied Telesis x530 board (Armada-385) from Chris - Misc minor changes (defconfig etc)
2019-01-21ARM: mvebu: add support for Allied Telesis x530Chris Packham
This is a range of stackable network switches. The SoC is Armada-385 and there are a number of variants with differing network port configurations. The DP variants are intended for a harsher operating environment so they use a different i2c mux and fit industrial-temp parts. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm64: dts: marvell: armada-ap806: reserve PSCI areaHeinrich Schuchardt
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any attempt to access it from U-Boot leads to an immediate crash. So let's make the same memory reservation as the vendor device tree. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Support 1 GB version of Turris MoxMarek Behún
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB or 1 GiB. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: dts: Fix Turris Mox device treeMarek Behún
DTC issues a warning because #address-cells and #size-cells properties are not set in the mdio node. Also add ethernet1 alias. Also add RTC node. Also fix USB3 regulator startup delay time. Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the speed value is not used byt the comphy driver for PCI Express, but should be 5 GHz nonetheless). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-27 14:10:33 +0000