| Age | Commit message (Collapse) | Author |
|---|
|
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Update DDR configuration with the latest update:
- PUBL_regs: DXnGCR[0]= according to ddr_width to disable Byte
lane 2/3 in 16bit
- fix LPDDR2/3 timing_calc to step RL/WL in relaxed
timings mode
- remove LPDDR3 RL3 (optional) support vs MR0[7]
because MR0[7] can't be read instead always apply
worse RL/WL for LPDDR3 when freq < 166MHz)
- change MR3 to 48ohm drive for LPDDR2/3
- change default ZPROG[7:4] = 0x1 for LPDDR2/3 ,
'0' is not allowed even when ODT not used
- use DQSTRN for LPDDR2/3 (it was not set in PIR)
- LPDDR3: set dqsge/dwsgx gate extension to 2,2
like LPDDR2
-DDRCTRL.dfitmg0:
+ for LPDDR3 tphy_wrlat = WL (as LPDDR2)
+ improvement for relaxed mode vs RL/Wl at corner case.
For example @533MHz RL/WL (relaxed) = 9/5 for LPDDR2/3
and correction to MR2 accordingly
- DDR_PCFGQOS1_1: port1 timeout relaxed from 0x00 to 0x40,
for LTDC.
- DDR_PCFGWQOS0_0: change vpr level from
11 to 12 in order to include the CPU on
the variable priority queue.
- DDR_SCHED: fix to consider 13 levels (13 levels - 1 = 0xC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Allow fractional support in DDR tools.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add the needed configurations for bootstage and
activate bootstage command.
BOOTSTAGE_REPORT is not activated by default.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
In initf_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us() before timer_init(); that cause crash for stm32mp1.
This patch solve the issue without changing the initialization sequence.
See also commit 97d20f69f53e ("Enable CONFIG_TIMER_EARLY with bootstage")
for other solution when DM is activated for TIMER.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Activate bootcount and use TAMP register to store the count value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Use SGI0 interruption and TAMP_BACKUP_MAGIC_NUMBER
to synchronize the core1 boot sequence requested by
core0 in psci_cpu_on():
- a initial interruption is needed in ROM code after
RCC_MP_GRSTCSETR_MPUP1RST (psci_cpu_off)
- the ROM code set to 0 the 2 registers
+ TAMP_BACKUP_BRANCH_ADDRESS
+ TAMP_BACKUP_MAGIC_NUMBER
when magic is not egual to
BOOT_API_A7_CORE0_MAGIC_NUMBER
This patch solve issue for cpu1 restart in kernel.
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Reorder the include files in alphabetic order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Use Kconfig to activate CONFIG_PREBOOT (empty by default).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add arch stm32mp for ENV migration step and drop more
items from include/configs/xxx.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch moves the the config SYS_MALLOC_LEN to
Kconfig as it is already done for zynq arch in
commit 01aa5b8f0503 ("Kconfig: Move config
SYS_MALLOC_LEN to Kconfig for zynq")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Move the ecc addr from driver to dts.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
LS1028AQDS Development System is a high-performance
computing, evaluation, and development platform that supports
LS1028A QorIQ Architecture processor.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Ls1028a SoC is based on Layerscape Chassis Generation 3.2
architecture with features:
2 ARM v8 Cortex-A72 cores, CCI400, SEC, DDR3L/4, LCD, GPU, TSN
ENETC, 2 USB 3.0, 2 eSDHC, 2 FlexCAN, 2 SPI, SATA, 8 I2C controllers,
6 LPUARTs, GPIO, SAI, qDMA, eDMA, GIC, TMU etc.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
The LX2160A integrated 6 PCIe Gen4 controllers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
The LS2080A has 8GB region for each PCIe controller, while the
other platforms have 32GB.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
- Update MPC83xx platform support to current best practices, etc.
|
|
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
|
|
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Add a U-Boot specific dts file, which encapsulates the needed
modifications to the Gazerbeam Linux device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Import the Linux device tree for the Gazerbeam board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
To support OF_EMBED, the MPC83xx architecture has to define the "_end"
symbol to correctly access the appended DT.
Fortunately, MPC8xx already defines the symbol, and the linker script is
quite similar to that of MPC83xx, so copy this approach for MPC83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Lots of stuff in processor.h was taken verbatim from the Linux kernel.
It was never synced, so most of it was removed or changed in the kernel
since it was imported.
Remove all the stuff that is unused in the current U-Boot sources;
should anybody feel the need to re-sync with the kernel, they can do it
later on.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
For a lot of inline assembly calls in the mpc8xxx and mpc83xx
directories, we already have convenient pre-defined helper functions,
but they're not used, resulting in hard-to-read code.
Use these helper functions where ever possible and useful.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
ppcDWstore/ppcDWload are hardly used by any board, but since they're
implemented in start.S, they're always present in every U-Boot image,
even if they're not needed.
Re-implement these fuctions in C with inline assembly, so that the
compiler can decide when to actually include them.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Don't use the legacy method of initializing the ethernet controller on
MPC83xx when DM is active.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
The fsl-esdhc driver can be used for the SDHC functionality on MPC83xx,
but it needs some additional definitions.
Add a clock.h file, so we can use the driver for MPC83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_LCRR_* settings to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the SPCR setting to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the arbiter configuration to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the system IO configuration setting to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate CONFIG_SYS_IMMR to Kconfig for MPC83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Mirate the HID configuration settings to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
The MPC85xx GPIO driver was converted to handle a broader range of SoCs.
Prepare the MPC83xx code for usage of this driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Replace the hard-coded CONFIG_SYS_NS16550_CLK value for the FDT fixup
with the previously introduced get_serial_clock function
This will make it possible to activate DM for serial devices on MPC83xx
later on.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
DM serial drivers on PowerPC determine their clock frequency via the
get_serial_clock function. This function is not Implemented yet for
MPC83xx.
This patch Implements the function so that DM serial drivers work on
MPC83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
The MPC8308 has two I2C controllers, but no PCI controller.
Fix the register map layout for this SoC.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_HIGH_BATS variable to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
