| Age | Commit message (Collapse) | Author |
|---|
|
The clocks are not dependent on the target but only on the SoC.
Therefore, convert the CONFIG_TARGET_x macros to the corresponding
CONFIG_ARCH_x. This will allow other targets to automatically use the
common code. Otherwise every new target would have to add itself to the
"#if defined(CONFIG_TARGET_x) || .." macros.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Erratum A-050382 states that the eDMA ICID programmed in the eDMA_AMQR
register in DCFG is not correctly forwarded to the SMMU.
The workaround consists in programming the eDMA ICID in the eDMA_AMQR
register in DCFG to 40.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
LX2160A chips have 4 sata controllers. Add missing base addresses for
SATA3 and SATA4.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
If SEC FW support is not enabled (ARMV8_SEC_FIRMWARE_SUPPORT=n), below
compilation error appears
arch/arm/include/asm/arch-fsl-layerscape/fsl_icid.h:169:4: error:
'CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT' undeclared here (not in a function)
Fix it by wrapping with CONFIG_IS_ENABLED().
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
These macros should only be used when CONFIG_FSL_CAAM is present.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
If the secure world reset handlers are used (via CONFIG_PSCI_RESET),
then do not use the layerscape-specific implementation.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
This allows the use of PSCI calls to trusted firmware to
initiate reset and poweroff events with CONFIG_PSCI_RESET and
CONFIG_ARM_PSCI_FW. This is desirable, for example, if the target
board has implemented a custom reset or poweroff procedure in EL3.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Hook buck12_reg to vtm avs supply
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Add tps65941 node and dependent wkup_i2c0 node needed for AVS class 0 support
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Link the vdd-supplies for the voltage domains under the VTM node. Also,
enable the node under SPL. This will enable the AVS class 0 support on
am65x-evm board.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached
to i2c0 bus. Add device node for this so that it can be controlled via
a regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Enable wkup_i2c0 as this is needed for voltage control.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Initialize avs class 0
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Initialize AVS class 0 so that mpu voltage rail is
programmed to the AVS class 0 compensated value.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
|
|
As part of disabling caches MMU as well gets disabled. But MMU is not
available on all armv7 cores like R5F. So disable MMU only if it is
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The default implementation of ERR_PTR/PTR_ERR maps errno values at the
and of the address range (e.g. -EINVAL/-22 gets 0xFFFFFFEA).
For socfpga gen5 SPL, this doesn't really work, as the heap is nearly
at the end of the 32 bit address range.
This patch adjusts the ERR_PTR_OFFSET to map errno values into the range
of the Boot ROM, which should not be used for valid pointers.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Provide optimized memcpy_{from,to}io() and memset_io(). This is required
when moving large amount of data to and from IO regions such as IP
registers or accessing memory mapped flashes.
Code is borrowed from Linux Kernel v5.4.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
add u-boot specific dtsi file for socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Also, add me as board maintainer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add phy-reset-gpios to reset phy
Add board_phy_config to configure phy
Enable DM_ETH
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Drop assigned clocks for clk node, this will break boot on i.MX8MM EVK
board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
When CONFIG_$(SPL_)CLK not defined, the clock controller device
not exist, so to avoid boot failure for platform not have
CONFIG_$(SPL_)CLK, add a check.
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Support pinctrl/clk/sdhc, include ddr4 timing data.
Log:
U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
CPU: Freescale i.MX8MNano rev1.0 at 24 MHz
Reset cause: POR
Model: NXP i.MX8MNano DDR4 EVK board
DRAM: 2 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add dtsi for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add cfg file for i.MX8MN DDR4
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No ROM INFO structure on iMX8MN, use new ROM API to get boot device
from ROM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has its own get_boot_device, so restrict with i.MX8MQ and
i.MX8MM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN follow same logic as i.MX8MM, so use spl_board_boot_device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add pin header for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN does not have LVTTL, it has a PE property
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add a dummy cpu type and support get_cpu_rev for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MN kconfig entry
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191104
-------------------
- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
|
|
- Various CPSW related improvements, DTS resync
|
|
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
|
|
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Move code for writing FCB/DBBT pages to a separate function
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
