summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2013-11-04blackfin: Move machine specific gpio_port_t structure back to blackfin arch ↵Steven Miao
folder. The gpio register mappings are different among blackfin processors. Signed-off-by: Steven Miao <realmz6@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-11-04blackfin: fix a warning in arch/blackfin/cpu/cpu.cMasahiro Yamada
This commit fixes: cpu.c:107: warning: ‘noreturn’ function does return Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-11-01ARM: OMAP5: DDR3: Change io settingsSRICHARAN R
The change from 0x64656465 to 0x64646464 is to remove the weak pull enabled on DQS, nDQS lines. This pulls the differential signals in the same direction which is not intended. So disabling the weak pulls improves signal integrity. On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being supplied a VREF! This was clearly a mistake. The second change improves the robustness of the interface and was specifically seen to cure corruption observed at high temperatures on some boards. With the above two changes better memory stability was observed with extended temperature ranges around 100C. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-11-01dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah
UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am335x: Enable CONFIG_OMAP_WATCHDOG supportTom Rini
There is a board-specific portion for calling watchdog enable itself, in main U-Boot. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini
Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01blackfin: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Sonic Zhang <sonic.zhang@analog.com>
2013-11-01m68k: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Jason Jin <Jason.jin@freescale.com>
2013-11-01x86: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org>
2013-11-01nios2: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Thomas Chou <thomas@wytron.com.tw>
2013-11-01nds32: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-10-31mips: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-10-31microblaze: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Michal Simek <michal.simek@xilinx.com>
2013-10-31openrisc: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2013-10-31avr32: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com>
2013-10-31sh: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-31sparc: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2013-10-31sh: Do not include start.o in lib$(CPU).oMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-31sparc: fix a link errorMasahiro Yamada
Before this commit, arch/sparc/lib/Makefile used both COBJS and COBJS-y. And it missed to add COBJS-y into OBJS. This means bootm.o was never compiled even if CONFIG_CMD_BOOTM=y Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2013-10-31ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/Masahiro Yamada
This patch moves S5PC, EXYNOS specific directory entries from the toplevel Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-10-31ARM: omap: move OMAP specific code under arch/arm/Masahiro Yamada
This patch moves OMAP specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
2013-10-31ARM: tegra: move Tegra specific code under arch/arm/Masahiro Yamada
This patch moves Tegra specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/*/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <TWarren@nvidia.com>
2013-10-31powerpc: convert makefiles to Kbuild styleMasahiro Yamada
Note: arch/powerpc/cpu/mpc8260/Makefile is originally like follows: ---<snip>--- START = start.o kgdb.o COBJS = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \ ---<snip>--- COBJS-$(CONFIG_ETHER_ON_SCC) = ether_scc.o ---<snip>--- $(LIB): $(OBJS) $(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o) The link rule `$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)' is weird. kbdg.o is not included in $(OBJS) but linked into $(LIB) and $(LIB) is not dependent on kgdb.o. (Broken dependency tracking) So, START = start.o kgdb.o shoud have been START = start.o SOBJS = kgdb.o That is why this commit adds kgdb.o to obj-y, not to extra-y. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de>
2013-10-31sandbox: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2013-10-31ARM: imx-common: convert makefiles to Kbuild styleMasahiro Yamada
Multiple targets are included in arch/arm/imx-common/Makefile In order to refactor it, we need to tweak Makefile and spl/Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31ARM: mxs: Enable DCDC converter for battery bootMarek Vasut
In case the board detected sufficient voltage for battery boot, make sure the DCDC converter is ON and the board is not running only from linregs, otherwise an instability will be observed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31mx6: Remove PAD_CTL_DSE_120ohm from i.MX6DL's IPU1_DI0_PIN4 pinOtavio Salvador
This removes the PAD_CTL_DSE_120ohm as done for i.MX6Q's IPU1_DI0_PIN4 pin definition and makes it aligned with 3.0.35-4.1.0 and 3.12 mainline kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-10-31mx5: lowlevel_init: Remove unused macroFabio Estevam
setup_wdog macro is not used anywhere, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-10-31ARM: mx5: Enable L2 cacheFabio Estevam
Enable L2 cache for improving the system performance. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31ARM: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31arm720t: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31arm920t: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31arm926ejs: convert makefiles to Kbuild styleMasahiro Yamada
Note1: In arch/arm/cpu/arm926ejs/spear/Makefile START := start.o was changed extra-$(CONFIG_SPL_BUILD) := start.o because spear/start.o is only used for SPL. Note2: START := start.o was missing from arch/arm/cpu/arm926ejs/mxs/Makefile. This commit simply adds extra-$(CONFIG_SPL_BUILD) := start.o Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31armv7: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31DWMMC: SMDK5420: Disable SMU for eMMCRajeshwari Shinde
SMDK5420 has a new Security Management Unit added for dwmmc driver, hence, configuring the control registers to support booting via eMMC. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-24fsl/mpc85xx: define common serdes_clock_to_string functionValentin Longchamp
This allows to share some common code for the boards that use a corenet base SoC. Two different versions of the function are available in fsl_corenet_serdes.c and fsl_corenet2_serdes.c files. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix t1040qds.c] Acked-by: York Sun <yorksun@freescale.com>
2013-10-24mpc8xxx: set x2 DDR3 refresh rate if SPD config requires itValentin Longchamp
If the DDR3 module supports industrial temperature range and requires the x2 refresh rate for that temp range, the refresh period must be 3.9us instead of 7.8 us. This was successfuly tested on kmp204x board with some MT41K128M16 DDR3 RAM chips (no module used, chips directly soldered on board with an SPD EEPROM). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix minor conflicts in fsl_ddr_dimm_params.h, lc_common_dimm_params.c, common_timing_params.h] Acked-by: York Sun <yorksun@freescale.com>
2013-10-24mpc8xxx: call i2c_set_bus_num in __get_spdValentin Longchamp
This is necessary with the new I2C subystem that was introduced lately. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2013-10-24powerpc: cast bi_memsize to ulong for %ld usageValentin Longchamp
When exporting the new memsize without reserved PRAM area, the -Wformat option produces a warning since %ld is used for snprintf and bi_memsize is phys_size_t. This patch removes this warning for all PRAM PowerPC boards. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2013-10-24powerpc/usb:Differentiate USB controller base addressramneek mehresh
Introduce different macros for storing addresses of multiple USB controllers. This is required for successful initialization and usage of multiple USB controllers inside u-boot Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-10-24powerpc/usb:Define CONFIG_USB_MAX_CONTROLLER_COUNT for all 85xx socsramneek mehresh
CONFIG_USB_MAX_CONTROLLER_COUNT macro recently defined for initializing all USB controllers on a given platform. This macro is defined for all 85xx socs Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-10-22Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2013-10-21Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2013-10-20usb: add enum usb_init_type parameter to usb_lowlevel_initTroy Kisky
This parameter will later be used to verify OTG ports. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20usb: am437x: Add support for am437x xhci USB hostDan Murphy
Add the support for the am437x xhci usb host. The xHCI host on AM437 is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy
Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20usb: omap: Move the xhci-omap header file to common locationDan Murphy
Moving the xhci-omap header to a more global location so that other code can reference this code. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20usb: new board-specific USB init interfaceMateusz Zalega
This commit unifies board-specific USB initialization implementations under one symbol (usb_board_init), declaration of which is available in usb.h. New API allows selective initialization of USB controllers whenever needed. Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20mx6: iomux: add GPR1 defines for use with nitrogen6xTroy Kisky
Select GPIO1 as the USB OTG ID pin for Nitrogen6x Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20OMAP5: USB: Add OMAP xHCI file and headerDan Murphy
Add the OMAP file for the xHCI Host controller This code will initilialize the proper components within the OMAP5 to enable the xHCI host controller. Signed-off-by: Dan Murphy <dmurphy@ti.com>
generated by cgit (git 2.34.1) at 2025-01-01 11:32:46 +0000