summaryrefslogtreecommitdiff
path: root/board/amcc
AgeCommit message (Collapse)Author
2007-04-18ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROMStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-02ppc4xx: Change SysACE address on KatmaiStefan Roese
With this new base address of the Xilinx SystemACE controller the Linux driver will be easier to adapt, since it can now be mapped via the "normal" ioremap() call. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-03-31ppc4xx: Update Katmai bootstrap commandStefan Roese
Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB is selected. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31ppc4xx: Fix "bootstrap" command for Katmai boardStefan Roese
The board specific "bootstrap" command is now fixed and can be used for the AMCC Katmai board to configure different CPU/PLB/OPB frequencies. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24Merge with /home/stefan/git/u-boot/acadiaStefan Roese
2007-03-24[PATCH] Add 4xx GPIO functionsStefan Roese
This patch adds some 4xx GPIO functions. It also moves some of the common code and defines into a common 4xx GPIO header file. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24[PATCH] Small Sequoia cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24[PATCH] Clean up 40EZ/Acadia supportStefan Roese
This patch cleans up all the open issue of the preliminary Acadia support. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-21Code cleanup. Update CHANGELOGWolfgang Denk
2007-03-21Merge with /home/stefan/git/u-boot/acadiaStefan Roese
2007-03-21[PATCH] Add AMCC Acadia (405EZ) eval board supportStefan Roese
This patch adds support for the new AMCC Acadia eval board. Please note that this Acadia/405EZ support is still in a beta stage. Still lot's of cleanup needed but we need a preliminary release now. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-16[PATCH] Use dynamic SDRAM TLB setup on AMCC Ebony eval boardStefan Roese
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the DDR memory are dynamically programmed matching the total size of the equipped memory (DIMM modules). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Fix file mode of sequoia.cStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Clear Sequoia/Rainier security engine reset bitsJohn Otken john@softadvances.com
Signed-off-by: John Otken john@softadvances.com <john@softadvances.com>
2007-03-08Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-03-08Merge with /home/stefan/git/u-boot/yucca-ddr2Stefan Roese
2007-03-08[PATCH] Update AMCC Luan 440SP eval board supportStefan Roese
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR inititializition. This includes DDR auto calibration and support for different DIMM modules, instead of the fixed setup used in the earlier version. This patch also enables the cache in FLASH for the startup phase of U-Boot (while running from FLASH). After relocating to SDRAM the cache is disabled again. This will speed up the boot process, especially the SDRAM setup, since there are some loops for memory testing (auto calibration). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08[PATCH] Update AMCC Yucca 440SPe eval board supportStefan Roese
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR inititializition. This includes DDR auto calibration and support for different DIMM modules, instead of the fixed setup used in the earlier version. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Small AMCC Katmai 440SPe updateStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-07Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-03-07[PATCH] Use dynamic SDRAM TLB setup on AMCC Ocotea eval boardStefan Roese
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the DDR memory are dynamically programmed matching the total size of the equipped memory (DIMM modules). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-06[PATCH] Speed optimization of AMCC Sequoia/Rainier DDR2 setupStefan Roese
As provided by the AMCC applications team, this patch optimizes the DDR2 setup for 166MHz bus speed. The values provided are also save to use on a "normal" 133MHz PLB bus system. Only the refresh counter setup has to be adjusted as done in this patch. For this the NAND booting version had to include the "speed.c" file from the cpu/ppc4xx directory. With this addition the NAND SPL image will just fit into the 4kbytes of program space. gcc version 4.x as provided with ELDK 4.x is needed to generate this optimized code. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-01[PATCH] Update AMCC Katmai 440SPe eval board supportStefan Roese
This patch updates the recently added Katmai board support. The biggest change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2 driver. Please note, that still some problems are left with some memory configurations. See the driver for more details. Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-20[PATCH] Clean up Katmai (440SPe) linker scriptStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-20[PATCH] Add support for the AMCC Katmai (440SPe) eval boardStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-30Merge with /home/sr/git/u-boot/denx-merge-srWolfgang Denk
2007-01-30[PATCH] Merge Yosemite & Yellowstone board portsStefan Roese
Now the AMCC eval boards Yosemite (440EP) and Yellowstone (440GR) share one config file and all board specific files. This way we don't have to maintain two different sets of files for nearly identical boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-19Minor code cleanup.Wolfgang Denk
2007-01-18[PATCH] Add support for AMCC Taishan PPC440GX eval boardStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-15Merge with /home/hs/SC3/u-bootWolfgang Denk
Some code cleanup.
2007-01-13[PATCH] Update Yellowstone (440GR) to display board rev and PCI bus speedStefan Roese
Now the board revision and the current PCI bus speed are printed after the board message. Also the EBC initialising is now done via defines in the board config file. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-13[PATCH] Update Yosemite (440EP) to display board rev and PCI bus speedStefan Roese
Now the board revision and the current PCI bus speed are printed after the board message. Also the EBC initialising is now done via defines in the board config file. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-13[PATCH] Update Sequoia (440EPx) to display board rev and PCI bus speedStefan Roese
Now the board revision and the current PCI bus speed are printed after the board message. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-05[PATCH] Clear PLB4A0_ACR[WRP] on Sequoia (440EPx)Stefan Roese
This fix will make the MAL burst disabling patch for the Linux EMAC driver obsolete. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-05[PATCH] Add DDR2 optimization code for Sequoia (440EPx) boardStefan Roese
This code will optimize the DDR2 controller setup on a board specific basis. Note: This code doesn't work right now on the NAND booting image for the Sequoia board, since it doesn't fit into the 4kBytes for the SPL image. Signed-off-by: Stefan Roese <sr@denx.de>
2006-12-22[PATCH] Fix sequoia flash autodetection (finally correct)Stefan Roese
Now 32MByte and 64MByte FLASH is know to work and other configurations should work too. Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-10Merge with /home/stefan/git/u-boot/denxStefan Roese
2006-10-23Fix sequoia separate object direcory building problems.Marian Balakowicz
2006-10-09Move "ar" flags to config.mk to allow for silent "make -s"Wolfgang Denk
Based on patch by Mike Frysinger, 20 Jun 2006
2006-10-09Coding style cleanupWolfgang Denk
2006-10-07Add CONFIG_BOARD_RESET to configure board specific reset functionStefan Roese
Patch by Stefan Roese, 07 Oct 2006
2006-10-04Fix TLB setup for Ocotea boardStefan Roese
Patch by Stefan Roese, 30 Sep 2006
2006-10-04Fix reset problem in sequoia sdram init codeStefan Roese
Patch by Stefan Roese, 23 Sep 2006
2006-09-13Add support for AMCC Rainier PPX440GRx eval boardStefan Roese
Patch by Stefan Roese, 13 Sep 2006
2006-09-12Add NAND environment support for PPC440EPx Sequoia NAND boot configStefan Roese
Patch by Stefan Roese, 12 Sep 2006
2006-09-07Add support for AMCC Sequoia PPC440EPx eval boardStefan Roese
- Add support for PPC440EPx & PPC440GRx - Add support for PPC440EP(x)/GR(x) NAND controller in cpu/ppc4xx directory - Add NAND boot functionality for Sequoia board, please see doc/README.nand-boot-ppc440 for details - This Sequoia NAND image doesn't support environment in NAND for now. This will be added in a short while. Patch by Stefan Roese, 07 Sep 2006
2006-09-04Merge with /home/m8/git/u-bootWolfgang Denk
2006-09-01Add support for a saving build objects in a separate directory.Marian Balakowicz
Modifications are based on the linux kernel approach and support two use cases: 1) Add O= to the make command line 'make O=/tmp/build all' 2) Set environement variable BUILD_DIR to point to the desired location 'export BUILD_DIR=/tmp/build' 'make' The second approach can also be used with a MAKEALL script 'export BUILD_DIR=/tmp/build' './MAKEALL' Command line 'O=' setting overrides BUILD_DIR environent variable. When none of the above methods is used the local build is performed and the object files are placed in the source directory.
2006-08-29PCIe endpoint support for AMCC Yucca 440SPe boardStefan Roese
Patch by Tirumala R Marri, 26 Aug 2006
generated by cgit (git 2.34.1) at 2024-12-29 04:34:09 +0000