| Age | Commit message (Collapse) | Author |
|---|
|
Expanded OCM TLB to allow access to 64K OCM as well as 256K of
internal SRAM.
Adjusted internal SRAM initialization to match updated user
manual recommendation.
OCM & ISRAM are now mapped as follows:
physical virtual size
ISRAM 0x4_0000_0000 0xE300_0000 256k
OCM 0x4_0004_0000 0xE304_0000 64k
A single TLB was used for this mapping.
Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Added include/asm-ppc/ppc4xx-isram.h and moved internal SRAM and
L2 cache DCRs from ppc440.h to this new header.
Also converted these DCR defines from lowercase to uppercase and
modified referencing modules to use them.
Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Depending on the configuration jumper "SATA SELECT", U-Boot disabled
either one PCIe node or the SATA node in the device tree blob. This
patch removes the unnecessary and even confusing warning, when the node
is not found at all.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].
The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
add CMD_DATA_SIZE macro to enable it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Affected boards:
db64360
db64460
katmai
taihu
taishan
yucca
cpc45
cpu87
eXalion
elppc
debris
kvme080
mpc8315erdb
integratorap
ixdp425
oxc
pm826
pm828
pm854
pm856
ppmc7xx
sc3
sc520_spunk
sorcery
tqm8272
tqm85xx
utx8245
Removed initialization of the driver from net/eth.c
Also, wrapped contents of pci_eth_init() by CONFIG_PCI.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch cleans up the 440SPe PCIe register usage. Now only defines
from the include/asm-ppc/4xx_pcie.h are used.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch reworks the 440GX interrupt handling so that the common 4xx
code can be used. The 440GX is an exception to all other 4xx variants
by having the cascading interrupt vectors not on UIC0 but on a special
UIC named UICB0 (UIC Base 0). With this patch now, U-Boot references
the 440GX UICB0 when UIC0 is selected. And the common 4xx interrupt
handling is simpler without any 440GX special cases.
Also some additional cleanup to cpu/ppc4xx/interrupt.c is done.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.
Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4aadf08826f6c31270f1eecd27964fd
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch disables the square wave output of the M41T62 RTC used on
Canyonlands & Glacier. Here the explanation:
The serial real-time clock part used in the design is an
STMicro M41T62. This part has a full-time 32KHz square wave
output that is connected to the TmrClk input to the
processor. The default state for this square wave output is
enabled so the output runs continuously when the board is
powered normally and also from the battery. The TmrClk input
to the processor goes to ground when the power is removed
from the board/processor, and therefore the running square
wave output is driving ground which drains the battery quickly.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:
include/configs/amcc-common.h
This header now includes all common configuration options/defines which
are removed from the board specific headers.
The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.
Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
* spi_cs_activate(): Activates the chipselect for a given slave
* spi_cs_deactivate(): Deactivates the chipselect for a given slave
* spi_cs_is_valid(): Determines if the given bus/chipselect
combination can be activated.
Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)
To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.
Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.
spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.
This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.
I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.
But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?
Changed in v4:
- Build fixes for various boards, drivers and commands
- Provide common struct spi_slave definition that can be extended by
drivers
- Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
- Make default bus and mode build-time configurable
- Override default SPI bus ID and mode on mx32ads and imx31_litekit.
Changed in v3:
- Add opaque struct spi_slave for controller-specific data associated
with a slave.
- Add spi_claim_bus() and spi_release_bus()
- Add spi_free_slave()
- spi_setup() is now called spi_setup_slave() and returns a
struct spi_slave
- soft_spi now supports four SPI modes (CPOL|CPHA)
- Add bus parameter to spi_setup_slave()
- Convert the new i.MX32 SPI driver
- Convert the new MC13783 RTC driver
Changed in v2:
- Convert the mpc8xxx_spi driver and the mpc8349emds board to the
new API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
|
|
This patch removes the used testdram() implementations of the board
that are maintained by myself.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.
This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:
csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG
I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch changes the kilauea and kilauea_nand (for NAND booting)
board port to not use a board specific DDR2 init routine anymore. Now
the common code from cpu/ppc4xx is used.
Thanks to Grant Erickson for all his basic work on this 405EX early
bootup.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch (Part 2 of 2):
* Rolls up a suite of changes to enable correct primordial stack and
global data handling when the data cache is used for such a purpose
for PPC40x-variants (i.e. CFG_INIT_DCACHE_CS).
* Related to the first, unifies DDR2 SDRAM and ECC initialization by
eliminating redundant ECC initialization implementations and moving
redundant SDRAM initialization out of board code into shared 4xx
code.
* Enables MCSR visibility on the 405EX(r).
* Enables the use of the data cache for initial RAM on
both AMCC's Kilauea and Makalu and removes a redundant
CFG_POST_MEMORY flag from each board's CONFIG_POST value.
- Removed, per Stefan Roese's request, defunct memory.c file for
Makalu and rolled sdram_init from it into makalu.c.
With respect to the 4xx DDR initialization and ECC unification, there
is certainly more work that can and should be done (file renaming,
etc.). However, that can be handled at a later date on a second or
third pass. As it stands, this patch moves things forward in an
incremental yet positive way for those platforms that utilize this
code and the features associated with it.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
When SATA is selected (via jumper J6) we need to disable the first PCIe
node in the device tree, so that Linux doesn't initialize it. Otherwise
the Linux SATA driver will fail to detect the devices.
The same goes the other way around too. So if PCIe is selected we need
to disable the SATA node in the device tree.
This is because PCIe port 0 and SATA on 460EX share the same pins
(multiplexed) and we have to configure in U-Boot which peripheral is
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch fixes the canyonlands config.mk file to enable correct
out-of-tree builds. Thanks to Wolfgang Denk for spotting this.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds fdt (flattened device tree) support to the AMCC
Acadia eval board. This increases the image size and it doesn't
fit anymore into 256kByte. Since we didn't want to remove features
from the configuration, we decided to increase the U-Boot image size
(add one flash sector).
Also changed the default environment definition to make it
independent of such changes.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add support for booting with a device tree blob. This is needed to boot
ARCH=powerpc kernels. Also add support for setting the eth0 mac address
via the ethaddr variable.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Since we didn't want to remove features from the configuration, we
decided to increase the U-Boot image size (add one flash sector).
Also changed the default environment definition to make it
independent of such changes.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
