summaryrefslogtreecommitdiff
path: root/board/esd
AgeCommit message (Collapse)Author
2008-10-31ppc4xx: Update PMC440 board supportMatthias Fuchs
This patch brings PMC440 board support up to date: - fix GPIO configuration - add misc_init_f() - use better values for usbact variable - fix USB 2.0 phy reset sequence - shrink BAR2 to save PCI address space - add FDT support Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31ppc4xx: Fix PMC440 BSP commandsMatthias Fuchs
This patch fixes the PMC440 BSP commands painit and selfreset Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31ppc4xx: Fix esd loadpci commandMatthias Fuchs
This patch fixes esd's loadpci command when not all memory on adapter boards is accessable via PCI. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31ppc4xx: Clean up PMC440 headerMatthias Fuchs
-Codingstyle cleanup -Remove unused GPIO define Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31ppc4xx: Handle other board variant in PMC440 FPGA codeMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21Cleanup: fix "MHz" spellingWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-18rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-10ppc4xx: Fix USB 2.0 phy reset sequenceMatthias Fuchs
This patch fixes USB 2.0 communication issues on some DU440 boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-10ppc4xx: Add strapping mode for 667MHz CPU frequency on DU440 boardMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-10ppc4xx: Fix DU440 GPIO configurationMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12Merge branch 'Makefile-next' of git://git.denx.de/u-boot-armWolfgang Denk
2008-09-12ppc4xx: Fix SDRAM inititialization of multiple 405 based board portsStefan Roese
This patch fixes a problem introdiced with patch bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by initdram()]. The boards affected are: - PCI405 - PPChameleonEVB - quad100hd - taihu - zeus Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-10rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10rename environment.c in env_embedded.c to reflect is functionalityJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-08ppc4xx: Cleanup CPCI405 linker scriptMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-08ppc4xx: Update CPCI405 variants handlingMatthias Fuchs
This patch replaces the BOARD_REVISION variable in include/config.mk by a using a temporary include file in the platform directory. The former way does not work anymore and the latter is also used by some other boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
Conflicts: board/esd/dasa_sim/dasa_sim.c Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-03ppx4xx: Fix broken DASA_SIM boardMatthias Fuchs
This patch adds initdram() to DASA_SIM boards that has been removed accidentally by a previous commit. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Remove reference to common/lists.o from some esd linker scriptsStefan Roese
This patch removes some direct references to common/lists.o from some esd linker scripts. This is necessary because the lists source was moved and is not in the "common" directory anymore. Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Remove obsolete or unused functions from some esd boardsMatthias Fuchs
This patch removes initdram() and testdram() from most esd 405 platforms. Some boards also have an empty dummy implementation of misc_init_f(). This is also removed. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Remove obsolete initdram() function from VOM405 boardMatthias Fuchs
This patch removed the obsolete initdram() function from VOM405 platform file. Some minor cleanup. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Cleanup VOM405 linker scriptMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Cleanup PLU405 platform fileMatthias Fuchs
This patch - wraps some long lines - removes unused/obsolete functions: misc_init_f() and initdram() Signed-off-by: Matthias Fuchs <mf@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Cleanup PLU405 linker scriptMatthias Fuchs
Signed-off-by: Matthias Fuchs <mf@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03ppc4xx: Increase U-Boot size to 384kB for PLU405 boardsMatthias Fuchs
Signed-off-by: Matthias Fuchs <mf@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-02Moved initialization of TULIP Ethernet controller to board_eth_init()Ben Warren
Affected boards: cu824 bab7xx adciop dasa_sim mousse mpc8540eval musenki mvblue pcippc2/pcippc6 sbc8240 stxssa Removed initialization of the driver from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Moved initialization of NS8382X Ethernet controller to board_eth_init()Ben Warren
Affected boards: bc3450 cpci5200 mecp5200 pf2000 icecube o2dnt pm520 sandpoint8245 total5200 tqm5200 Removed initialization of the driver from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-08-19Clean up usage of icache_disable/dcache_disableKumar Gala
There is no point in disabling the icache on 7xx/74xx/86xx parts and not also flushing the icache. All callers of invalidate_l1_instruction_cache() call icache_disable() right after. Make it so icache_disable() calls invalidate_l1_instruction_cache() for us. Also, dcache_disable() already calls dcache_flush() so there is no point in the explicit calls of dcache_flush(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-13drivers/mtd/nand: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-12Fixing coding style issuesWilliam Juul
- Fixing leading white spaces - Fixing indentation where 4 spaces are used instead of tab - Removing C++ comments (//), wherever I introduced them Signed-off-by: William Juul <william.juul@tandberg.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12Update MTD to that of Linux 2.6.22.1William Juul
A lot changed in the Linux MTD code, since it was last ported from Linux to U-Boot. This patch takes U-Boot NAND support to the level of Linux 2.6.22.1 and will enable support for very large NAND devices (4KB pages) and ease the compatibility between U-Boot and Linux filesystems. This patch is tested on two custom boards with PPC and ARM processors running YAFFS in U-Boot and Linux using gcc-4.1.2 cross compilers. MAKEALL ppc/arm has some issues: * DOC/OneNand/nand_spl is not building (I have not tried porting these parts, and since I do not have any HW and I am not familiar with this code/HW I think its best left to someone else.) Except for the issues mentioned above, I have ported all drivers necessary to run MAKEALL ppc/arm without errors and warnings. Many drivers were trivial to port, but some were not so trivial. The following drivers must be examined carefully and maybe rewritten to some degree: cpu/ppc4xx/ndfc.c cpu/arm926ejs/davinci/nand.c board/delta/nand.c board/zylonite/nand.c Signed-off-by: William Juul <william.juul@tandberg.com> Signed-off-by: Stig Olsen <stig.olsen@tandberg.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-01Fix compilation error for TASREGTsiChung Liew
TASREG is ColdFire platform, the include ppc4xx.h in board/esd/common/flash.c causes conflict. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-07-14Code cleanup: fix old style assignment ambiguities like "=-" etc.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-13ppc4xx: Remove redundant ft_board_setup() functions from some 4xx boardsStefan Roese
This patch removes some ft_board_setup() functions from some 4xx boards. This can be done since we now have a default weak implementation for this in cpu/ppc4xx/fdt.c. Only board in need for a different/custom implementation like canyonlands need their own version. Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-10ppc4xx: Fix printf format warnings now visible with the updated format checkStefan Roese
This patch fixes ppc4xx related printf format warning. Those warnings are now visible since patch dc4b0b38d4aadf08826f6c31270f1eecd27964fd [Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is really helpful. Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-02Cleanup out-or-tree building for some boards (.depend)Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-12Change initdram() return type to phys_size_tBecky Bruce
This patch changes the return type of initdram() from long int to phys_size_t. This is required for a couple of reasons: long int limits the amount of dram to 2GB, and u-boot in general is moving over to phys_size_t to represent the size of physical memory. phys_size_t is defined as an unsigned long on almost all current platforms. This patch *only* changes the return type of the initdram function (in include/common.h, as well as in each board's implementation of initdram). It does not actually modify the code inside the function on any of the platforms; platforms which wish to support more than 2GB of DRAM will need to modify their initdram() function code. Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc MPC8641HPCN. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03ppc4xx: Remove superfluous dram_init() call or replace it by initdram()Stefan Roese
Historically the 405 U-Boot port had a dram_init() call in early init stage. This function was still called from start.S and most of the time coded in assembler. This is not needed anymore (since a long time) and boards should implement the common initdram() function in C instead. This patch now removed the dram_init() call from start.S and removes the empty implementations that are scattered through most of the 405 board ports. Some older board ports really implement this dram_init() though. These are: csb272 csb472 ERIC EXBITGEN W7OLMC W7OLMG I changed those boards to call this assembler dram_init() function now from their board specific initdram() instead. This *should* work, but please test again on those platforms. And it is perhaps a good idea that those boards use some common 405 SDRAM initialization code from cpu/ppc4xx at some time. So further patches welcome here. Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-21Big white-space cleanup.Wolfgang Denk
This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-14Fix config files for out-of-tree buildingWolfgang Denk
Several board/<...>/config.mk files include dynamically built (by the Makefile) config files but used the wrong file name of $(TOPDIR)/board/$(BOARDDIR)/config.tmp instead if the correct $(OBJTREE)/board/$(BOARDDIR)/config.tmp The bug is nasty because the build result is correct for the (normal) in-tree builds, and because 'sinclude' is used no errors get raised even for out-of-tree build tests. But out-of-tree builds use an incomplete and thus usually incorrect configuration... Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-25ppc4xx: Add bootcount limit handling for APC405 boardsMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Small coding style cleanup for the latest esd patchesStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2008-04-22ppc4xx: Update CPU strapping for PMC440 boardsMatthias Fuchs
This patch removes the temporary 'test' strapping option of the sbe command. The '667' strapping option now uses a PLB/PCI divider of 3. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Remove unused APC405 strataflash driverMatthias Fuchs
The APC405 board support has been migrated to use the common CFI flash driver. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Update APC405 board supportMatthias Fuchs
- enable esd's auto_update mechanism - fix LCD support on latest hardware revision (uses other LCD controller) - support alternative flash layout on rev. 1.8 boards - coding style cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: update esd's common auto_update code for 405 boardsMatthias Fuchs
- Coding style cleanup (long lines) - improve handling of protected flash regions - remove dead code Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Update esd's common LCD code for 405 boardsMatthias Fuchs
- Coding style cleanup (long lines) - Add s1d13505 support - Make some functions return a result code instead of void Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Update FPGA image for APC405 boardsMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-22ppc4xx: Update bootlogo for APC405 boardsMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
generated by cgit (git 2.34.1) at 2024-12-27 22:31:10 +0000