| Age | Commit message (Collapse) | Author |
|---|
|
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
TFABOOT support includes:
- ls1043ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN and QE address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
freescale.com domain is no longer reachable, so switch the
maintainers' emails to nxp.com domain instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This board has soldered DDR chips. To reduce the SPL image size,
use static DDR setting instead of dynamic DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
|
|
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Optimize board-specific cpo for erratum A-009942 on b4860qds,
ls1043aqds, ls1043ardb, ls1046aqds, ls1046ardb, ls2080ardb,
t102xqds, t102xrdb, t1040qds, t104xrdb, t208xqds, t208xrdb,
t4qds, t4rdb boards.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
sec_init() which was earlier called in misc_init_r()
is now done in board_init() before PPA init as SEC
block will be used during PPA image validation.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Update maintainers for secure boot targets.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This patch updates clk_adjust to actual value for boards with
T-series and LS-series SoCs to match the setting of clk_adjust
in latest ddr driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity
by setting relative bit in SCFG_INTPCR register, because AQR105
interrupt is low active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
gd->env_addr will be initialized in env_init() in
common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined.
So no need to do it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The current 'cpld reset' will just write global_rst register
but couldn't switch to NOR boot if the board's switches are
for NAND/SD boot. So need to write rcw source registers for
NOR boot as well.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
QE-HDLC and USB multi-use the pins, modify the pin-muxing code
for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins
to QE-HDLC, if not, assgin it to USB
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Pin-muxing code should be in config_board_mux, move USB muxing
config to config_board_mux.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Change RCW for SD boot and NAND boot.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.
Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.
gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This patch also expose the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing
in the MAINTAINERS file, so add them for completeness.
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
|
