| Age | Commit message (Collapse) | Author |
|---|
|
To normal mode, use APS switching mode.
To standy mode, use PFM switching mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
|
|
Since a clock function setup_gpmi_io_clk is implemented for GPMI
IO clock settings, change to use this common function in GPMI setup.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Add the pfuze100 initialization in power_init_board for imx6q/dl
sabreauto board.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
|
|
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Let HDMI splash screen support work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
The single file conflict below is actually trivial.
Conflicts:
board/boundary/nitrogen6x/nitrogen6x.c
|
|
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
|
|
Turn all local symbols into static in order to make sparse happy.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Tested by booting a mainline kernel via TFTP.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Use the latest DDR and clock settings as the one from Freescale BSP.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>
|
|
Currently board_eth_init() always return 0, but we should propagate the error
when cpu_eth_init() fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflicts:
drivers/serial/Makefile
|
|
There are 3 IO expanders on the mx6qsabreauto all reset by the
same GPIO, just set it to high to use the IO.
Signed-off-by: Renato Frias <b13784@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.
Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c
|
|
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.
By the way, remove some unused pad control definitions.
There is no change of behavior.
Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
IIM:
- Homogenize prg_p naming (the reference manuals are not always self-consistent
for that).
- Add missing SCSx and bank registers.
- Fix the number of banks on i.MX53.
OCOTP:
- Rename iim to ocotp in order to avoid confusion.
- Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
reference manual.
- Merge the existing spinoff gp1 fuse definition on i.MX6.
- Fix the number of banks on i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board
may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo
(MX6DL) by including the proper header.
Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd
only support MX6Q, so they include mx6q_pins.h.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
|
|
mx6qsabreauto has a AR8031 Gigabit PHY.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
